Novel B-doped BiOCl nanosheets with exposed (001) facets and photocatalytic mechanism of enhanced degradation efficiency for organic pollutants

Sample Fabrication of BiOCl Nanosheets with Low Specific Surface Area for Efficient Photocatalytic Degradation of Organic Wastewater

BiOCl photocatalyst with excellent performance has been prepared by a simple liquid-solid phase transition method. Three BiOCl-x (x = 0.5, 0.75, 1.0) photocatalysts were obtained by changing the amount of HCl in the preparation process. The main dominant crystal planes are (001), (002), and (003). Their forbidden bandwidths are reduced to 2.81, 2.89, and 2.84 eV. The samples were characterized by X-ray diffractometer, high-resolution field emission scanning electron microscopy, transmission electron microscopy, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, Fourier infrared spectrometry, UV-vis diffuse reflection spectrometer, and UV-vis spectrophotometer. The degradation mechanism of BiOCl-x on Rhodamine B(RhB) has been investigated by quenching experiments on active materials. ·O2- was the primary degradation agent. When the dosage of HCl was 0.75 mL, the degradation effect of RhB was the best under the same experimental conditions. In visible light, RhB was almost completely degraded within 15 min, demonstrating an excellent photocatalytic degradation efficiency.

Facile construction of copper-doped metal organic framework as a novel visible light-responsive photocatalyst for contaminant degradation

ABSTRACTMetal-organic frameworks (MOFs) with photocatalytic activity have garnered significant attentions in environmental remediation. Herein, copper-doped zeolitic imidazolate framework-7 (Cu-doped ZIF-7) was synthesized rapidly and easily using a microwave-assisted technique. Various analytical and spectroscopic methods were employed to access the framework, morphology, light absorption, photo-electrochemical and photocatalytic performance of the synthesized materials. Compared to ZIF-7, Cu/ZIF-7 (molar ratio of Cu2+ to Zn2+ is 1:1) demonstrates superior visible light absorption ability, narrower band gap, enhanced charge separation capability, and reduced electron-hole recombination performance. Under visible light irradiation, Cu/ZIF-7 serves as a Fenton-like catalyst and demonstrates exceptional activity for contaminant degradation, while virgin ZIF-7 remains inactive. With the addition of 9.8 mmol H2O2 and exposure to visible light for 30 min, 10 mg of Cu/ZIF-7 can completely decompose RhB solution (10 mg/L, 50 mL). The synergistic effect of the Cu/ZIF-7/H2O2/visible light system is attributed to visible light photocatalysis and Fenton-like reactions. Cu/ZIF-7 demonstrates excellent catalytic performance stability, with only a slight decrease in degradation efficiency from an initial 97.0% to 95.4% over four cycles. Additionally, spin-trapping ESR measurements and active species trapping experiments revealed that h+ and ·OH occupied a significant position for Rhodamine B (RhB) degradation. Degradation intermediate products of Rhodamine B have been identified using UPLC-MS, and the degradation pathways have been proposed and discussed. This work offers a facile and efficient technique for developing MOF-based visible light photocatalysts for water purification.

Enhanced Photocatalytic Degradation of Indoor Low Concentration Gaseous Formaldehyde by Asymmetric Silveriodate Composited with 2D or 3D Bismuth Oxybromide

Formaldehyde is one of the most hazardous and typical indoor VOCs air pollutants. Asymmetric AgIO3 was respectively composited with 3D hierarchically structured BiOBr and 2D BiOBr nanosheets to photodegrade gas-phase formaldehyde. Ag/AgIO3 /BiOBr(CMC) demonstrated better photocatalytic performance than Ag/AgIO3 /BiOBr owning to the role of biomass solvent sodium carboxymethyl cellulose in increasing the specific surface area, reducing the band gap and changing the dominant facets. Moreover, Ag nanoparticles coming from the reduction in AgIO3 were confirmed by XRD, SEM and XPS. The surface plasma resonance effect of Ag NPs improved the efficiency of the light quantum. Besides, different exposed facets of {010} in BiOBr(CMC) and {001} in BiOBr resulted in distinct oxygen vacancy structures.O 2 2 - could be generated via a two-electron transfer pathway on the {010} dominant facets surface in AABR-CMC, leading to the change in photolysis pathway and facilitating more · OH produced by AABR-CMC. Compared with pure AgIO3 and BiOBr or BiOBr(CMC), the photocatalytic efficiency of the composites was improved significantly. Optimal photodegradation efficiency for HCHO was achieved for AABR-75 and AABR-CMC50.

Constructing BiOBr1-xIx-y with Abundant Surface Br Vacancies for Excellent Visible-Light Photodegradation Capability of High-Concentration Refractory Contaminants

Bismuth oxybromide (BiOBr) is a promising photocatalytic semiconductor material due to its unique hierarchical structure and band structure. However, its photocatalytic applications are restricted due to its narrow visible-light absorption range and poor photooxidation capability. In this study, BiOBr1-xIx-y with rich surface Br vacancies (BrVs-rich BiOBr1-xIx-y) was created via a facile indirect substitution strategy. Benefiting from the broadened visible-light response range and reduced recombination rate of photogenerated carriers, BiOBr1-xIx-y shows excellent visible-light photodegradation ability for high-concentration refractory contaminants, such as phenol, tetracycline, bisphenol A, rhodamine B, methyl orange, and even real wastewater. At the same time, the Br vacancies can regulate the band structure of BiOBr1-xIx-y and serve as trap states to promote charge separation, thus facilitating surface photoredox reactions. An in-depth investigation of the Br vacancy effect and photodegradation mechanism was conducted. This novel study revealed the significance of Br vacancies in enhancing the photocatalytic performance of BiOBr under visible light, providing a promising strategy for improving the utilization efficiency of sunlight in wastewater treatment.

Boosting the photocatalytic CO2 reduction reaction over BiOCl nanosheet via Cu modification

The development of photocatalytic reduction of CO₂ is hindered by slow surface reaction kinetics due to the high activation barrier of CO₂ and the lack of activation centers in the photocatalyst. To overcome these limitations, this study focuses on enhancing the photocatalytic performance through incorporating Cu atoms into BiOCl. By introducing a minute amount of Cu (0.18 wt%) into BiOCl nanosheets, significant improvements were achieved, with a CO yield of 38.3 µmol g^-1 from CO₂ reduction, surpassing that of pristine BiOCl by 50%. To explore the surface dynamics of CO₂ adsorption, activation and reactions, in situ DRIFTS was employed. Theoretical calculations were further performed to elucidate the role of Cu in the photocatalytic process. The results demonstrate that the incorporation of Cu into BiOCl induces surface charge redistribution, which facilitates efficient trapping of photogenerated electrons and accelerates the separation of photogenerated charge carriers. Furthermore, Cu modification on BiOCl effectively lowers the activation energy barrier by stabilizing the COOH* intermediate, thereby turning the rate-limiting step from COOH* formation to CO* desorption and boosting the CO₂ reduction process. This work unveils the atomic-level role of modified Cu in enhancing the CO₂ reduction reaction and presents a novel concept for achieving highly efficient photocatalysts.

Bismuth-based nanostructured photocatalysts for the remediation of antibiotics and organic dyes

A serious threat to human health and the environment worldwide, in addition to the global energy crisis, is the increasing water pollution caused by micropollutants such as antibiotics and persistent organic dyes. Nanostructured semiconductors in advanced oxidation processes using photocatalysis have recently attracted a lot of interest as a promising green and sustainable wastewater treatment method for a cleaner environment. Due to their narrow bandgaps, distinctive layered structures, plasmonic, piezoelectric and ferroelectric properties, and desirable physicochemical features, bismuth-based nanostructure photocatalysts have emerged as one of the most prominent study topics compared to the commonly used semiconductors (TiO₂ and ZnO). In this review, the most recent developments in the use of photocatalysts based on bismuth (e.g., BiFeO₃, Bi₂MoO₆, BiVO₄, Bi₂WO₆, Bi₂S₃) to remove dyes and antibiotics from wastewater are thoroughly covered. The creation of Z-schemes, Schottky junctions, and heterojunctions, as well as morphological modifications, doping, and other processes are highlighted regarding the fabrication of bismuth-based photocatalysts with improved photocatalytic capabilities. A discussion of general photocatalytic mechanisms is included, along with potential antibiotic and dye degradation pathways in wastewater. Finally, areas that require additional study and attention regarding the usage of photocatalysts based on bismuth for removing pharmaceuticals and textile dyes from wastewater, particularly for real-world applications, are addressed.

Bismuth-doped g-C3N4/ZIF-8 heterojunction photocatalysts with enhanced photocatalytic performance under visible light illumination

In this work, g-C₃N₄/ZIF-8 heterojunction photocatalysts were synthesised by the process by which the metal-organic framework ZIF-8 nanoparticles were grown onto the g-C₃N₄ layer in situ. Bismuth element was doped into the as-prepared g-C₃N₄/ZIF-8 material and a new type of Bi@g-C₃N₄/ZIF-8 composite photocatalysts was manufactured, in which the doping element acts in adjusting the bandgap in the photocatalysts. The prepared photocatalysts were characterised by XRD, FESEM, TEM, FTIR, XPS, UV-VIS DRS, photoluminescence and photo-electrochemical experiments. The results show that the ZIF-8 nanoparticles grown in situ were well-formed onto the g-C₃N₄ layer, and bismuth was evenly doped into the gaps of the g-C₃N₄/ZIF-8 framework. The degradation rate of methylene blue by CNZ-1.5(Bi)-12, which was a photocatalyst composed of 12% Bi-doped with g-C₃N₄/ZIF-8 material (the mass ratio of g-C₃N₄: ZIF-8 = 1:1.5), reached 86.6% under visible light irradiation within 60 min. The free radical scavenging experiment and electron spin resonance spectroscopy showed that ∙OH was the main active substance. Bismuth doping into the photocatalytic system promotes the excitation of electrons from the valence band to the conduction band and provides a good channel for the transmission of photogenerated carriers as well. It is achieved that intensive visible light absorption, the enhanced separation efficiency of photogenerated carriers, and excellent thermal stability and high recyclability in the novel composite photocatalyst, owing to the synergistic effect of the introduced bismuth with the heterostructure of g-C₃N₄/ZIF-8. Therefore, the synthesised Bi@g-C₃N₄/ZIF-8 heterojunction photocatalysts may be used as a good photocatalyst for purifying and degrading organic matter in sewage.

In Situ Construction of BiO(ClBr)(1-x)/2Ix-n Solid Solution with Appropriate Surface Iodine Vacancies for Synergistically Boosting Visible-Light Photo-Oxidation Capability

A proposed BiO(ClBr)_(1-x)/2I_x-n solid solution containing abundant iodine vacancies has been constructed through a facile solvothermal treatment strategy. Fascinatingly, the iodine-vacancy BiO(ClBr)_(1-x)/2I_x-n solid solution exhibits an outstanding visible-light photocatalytic degradation property for the environmentally hazardous pollutants of methyl orange, tetracycline, and phenol solutions, which is credited to the synergistic effect of iodine vacancies and the solid solution. By manipulating the molar ratios of Cl, Br, and I, the band structure of the solid solution attained is controlled, enabling the samples to maximize the harvest of visible light and to possess strong oxidation features. More importantly, the construction of iodine vacancies is bound to modulate the local surface atomic structure and promotes the efficiency of the separation of photogenerated carriers. Given these, the microstructure and physicochemical and photoelectrochemical properties of the photocatalysts are fully characterized in a series. In addition, the iodine-vacancy BiO(ClBr)_(1-x)/2I_x-n solid solution has a stable crystal structure that permits favorable recyclability even after multiple cycles of degradation. This study sheds light on the significance of the simultaneous existence of vacancy and the solid solution for the enhanced performance of photocatalysts and opens up new insights for sustainable solar-chemical energy conversion.

Recent advances in bismuth oxyhalides photocatalysts and their applications

Bismuth oxyhalides photocatalysts exhibit great potential to solve the energy and environmental issues under visible light due to their unique physicochemical and optical properties. However, the photocatalytic activity of pristine bismuth oxyhalides remains unsatisfactory because of their inherent drawbacks. Up to now, many strategies have been used to improve the photocatalytic performance. In this review, the basic mechanism, unique properties and structure of bismuth oxyhalides photocatalysts have been introduced, and the common techniques of synthesis, modification, and main applications have been discussed. Finally, new insights are proposed to meet the future challenges and development of the photocatalysts, which can provide better knowledge for the advancement of the related research areas.

Halides and oxyhalides-based photocatalysts for abatement of organic water contaminants - An overview

Recently, halides (silver halides, AgX; perosvkite halides, ABX₃) and oxyhalides (bismuth oxyhalides, BiOX) based nanomaterials are noticeable photocatalysts in the degradation of organic water pollutants. Therefore, we review the recent reports to explore improvement strategies adopted in AgX, ABX₃ and BiOX (X = Cl, Br and I)-based photocatalysts in water pollution remediation. Herein, the photocatalytic degradation performances of each type of these photocatalysts were discussed. Strategies such as tailoring the morphology, crystallographic facet exposure, surface area, band structure, and creation of surface defects to improve photocatalytic activities of pure halides and BiOCl photocatalysts are emphasized. Other strategies like metal ion and/or non-metal doping and construction of composites, adopted in these photocatalysts were also reviewed. Furthermore, the way of production of active radicals by these photocatalysts under ultraviolet/visible light source is highlighted. The deciding factors such as structure of pollutant, light sources and other parameters on the photocatalytic performances of these materials were also explored. Based on this literature survey, the need of further research on AgX, ABX₃ and BiOX-based photocatalysts were suggested. This review might be beneficial for researchers who are working in halides and oxyhalides-based photocatalysis for water treatment.

g-C3N4 nanosheets functionalized yttrium-doped ZrO2 nanoparticles for efficient photocatalytic Cr(VI) reduction and energy storage applications

Novel g-C₃N₄ functionalized yttrium-doped ZrO₂ hybrid heterostructured (g-YZr) nanoparticles have been synthesized to investigate photocatalytic Cr(VI) reduction as well as electrochemical energy storage applications. The nanoparticles have been characterized to examine their structural, optical, and photocatalytic properties. XRD confirmed the incorporation of dopant ions and heterostructure development between g-C₃N₄ and doped ZrO₂. When g-C₃N₄ was doped with ZrO_2, the ability of light adsorption was greatly enhanced due to the narrow band gap. The distinctive structure of g-YZr exhibited outstanding photocatalytic Cr(VI) reduction owing to its superior surface area, which greatly prevented the charge carriers' recombination rate and exhibited superior photocatalytic performance within 90 min of solar light irradiation. Furthermore, these catalysts demonstrated similar catalytic Cr(VI) reduction activity following four repeatability tests, indicating the exceptional structural stability of g-YZr catalysts. The electrochemical performance of the electrodes revealed that g-YZr exhibited superior specific capacitance over the other electrodes owing to extra energetic sites and robust synergic effect. Enhanced specific capacitance and long cyclic stability of the hybrid heterostructures displayed their usefulness for energy storage applications.

Advances in facet-dependent photocatalytic properties of BiOCl catalyst for environmental remediation

Bismuth chloride oxide (BiOCl) is a typical V-VI-VII ternary oxide material, which is one of the widely studied metal oxides due to its unique surface, electronic and photocatalytic properties. However, the broad bandgap and the large number of photogenerated electron-hole pair complexes of BiOCl limit its photocatalytic efficiency. Since the photocatalytic performance of BiOCl is highly dependent on its exposed crystallographic facets, research attention has increasingly focused on the different structures and properties possessed by different crystallographic facets of BiOCl. This article reviews the basic principles of using different crystalline surfaces of BiOCl materials to enhance photocatalytic activity, summarizes the applications of BiOCl single-crystal catalysts and composite catalysts in the environmental field, and provides an outlook on the challenges and new research directions for future development in this emerging frontier area. It is hoped that the crystalline surface-related photocatalysis of BiOCl can be used to provide new guidance for the rational design of novel catalysts for various energy and environment-related applications.

Indirect Substitution Constructing Halogen-Vacancy BiOCl1-xIn Solid Solution with a Suitable Surface Structure for Enhanced Photoredox Performance

Photocatalytic technology has made a series of breakthroughs in environmental remediation, but the degradation performance of persistent heavy metal ions and organic pollutants is not particularly excellent. In addition, the layered structure of bismuth oxyhalides (BiOX, X = I, Br, and Cl) has been a popular material for photodegradation and photoelectrochemistry. Accordingly, with a view to construct a suitable band structure and control the surface structure, it is necessary to develop a strategy to synthesize a BiOCl_1-xI_n solid solution with halogen vacancies. In this study, halogen vacancies are in situ introduced into the BiOCl_1-xI_n solid solution through constructing chemical bonds between the hydroxyl groups in glycerol and the I ions during the growth process. The band of the halogen-vacancy BiOCl_1-xI_n solid solution is widened and active sites centered at halogen vacancies are formed in the direction favorable for the photocatalytic reaction, resulting in enhanced performance in the reduction of Cr(VI) and the oxidation of phenol. The results obtained can provide a new idea for the design of efficient photocatalysts by controlling the formation of halogen vacancies.

Progress on photocatalytic semiconductor hybrids for bacterial inactivation

Due to its use of green and renewable energy and negligible bacterial resistance, photocatalytic bacterial inactivation is to be considered a promising sterilization process. Herein, we explore the relevant mechanisms of the photoinduced process on the active sites of semiconductors with an emphasis on the active sites of semiconductors, the photoexcited electron transfer, ROS-induced toxicity and interactions between semiconductors and bacteria. Pristine semiconductors such as metal oxides (TiO₂ and ZnO) have been widely reported; however, they suffer some drawbacks such as narrow optical response and high photogenerated carrier recombination. Herein, some typical modification strategies will be discussed including noble metal doping, ion doping, hybrid heterojunctions and dye sensitization. Besides, the biosafety and biocompatibility issues of semiconductor materials are also considered for the evaluation of their potential for further biomedical applications. Furthermore, 2D materials have become promising candidates in recent years due to their wide optical response to NIR light, superior antibacterial activity and favorable biocompatibility. Besides, the current research limitations and challenges are illustrated to introduce the appealing directions and design considerations for the future development of photocatalytic semiconductors for antibacterial applications.

Facile synthesize of CdS QDs decorated Bi2MoO6/Bi2Mo3O12 heterojunction photocatalysts and enhanced performance of visible light removal of organic pollutants

In this work, the CdS quantum dots (QDs) decorated Bi₂MoO₆/Bi₂Mo₃O₁₂ (BMO) heterojunction photocatalyst (C/BMO) has been successfully synthesized using a facile two-step hydrothermal method. The as-prepared photocatalysts were characterized by XRD, FTIR, XPS, FESEM, TEM, UV-vis DRS, PL and photoelectrochemical measurements to investigate the effects of CdS(QDs) and BMO heterojunction on the structure, morphology, optical and charge carrier transmission characteristics of the photocatalysts. Narrow band gap and superior catalytic activities were found in C/BMO as compared with pure BMO. Moreover, the C/BMO photocatalyst containing twice CdS content (2-C/BMO) exhibits even higher photocatalytic activity and stability. After exposure to visible light for 30 min, the degradation rate of Rhodamine B (RhB), Methylene blue (MB) and Ofloxacin (OFX) by 2-C/BMO reached 95%, 92% and 76%, respectively. Radicals scavenging experiments and electron spin-resonance spectroscopy (ESR) investigations indicated that the superoxide radical anions (∙O2- ), hole (h⁺) and hydroxyl radicals (•OH) are the dominating active species in the photodegradation processes. ∙O2- and h⁺ are the key factors in the degradation of RhB and OFX solutions, and •OH is the major determinant in removal of MB. The process and photocatalytic mechanism on 2-C/BMO was discussed. Well absorption of visible light, effective separation of photoelectron-hole pairs and the transportation of photogenerated carriers at the interfaces of ternary semiconductor heterojunction are suggested as the key factors to enhance the photocatalytic performance of the photocatalysts.

Recent advances in bismuth oxyhalide photocatalysts for degradation of organic pollutants in wastewater

Photocatalysis has been considered as an environmental-friendly strategy for degradation of organic pollutants to the nontoxic products of H2O and CO2. Compared to metal oxide semiconductors, BiOX (X = Cl, Br and I) photocatalysts exhibit some advantages, such as, unique layered structure, good chemical stability and superior photocatalytic activity. This review provides an overview on the controllable synthesis of BiOX-based photocatalysts and their application in photodegradation of organic pollutants. Firstly, the controllable synthesis of BiOX is introduced, including hydrothermal, solvothermal, hydrolysis, precipitation, two-phase methods, ultrasonic/microwave-assisted methods, and physical methods. Then, the doping and surface modification of BiOX are summarized, including non-metal doping, metal doping, dual doping, and the modification by introducing surface terminations or carriers. In addition, the heterojunctions of BiOX/BiOY and BiOX/Bi m O n X z are introduced. At last, the promising research trends of BiOX-based photocatalysts are put forward. The main purpose is providing practical guidelines for developing high-performance BiOX photocatalysts.

Construction of a novel step-scheme CdS/Pt/Bi2MoO6 photocatalyst for efficient photocatalytic fuel denitrification

Construction of step-scheme (S-scheme) heterojunction (HJ) structures is an excellent strategy to achieve efficient photogenerated carrier separation and retain strong redox ability. Recently, the development of efficient S-scheme HJ photocatalysts for the degradation of environmental organic pollutants has attracted considerable attention. In this work, a novel S-scheme CdS/Pt/Bi2MoO6 (CPB) photocatalyst was prepared for the first time by sonochemical and solvothermal methods. By anchoring Pt nanoparticles (NPs) at the interface between CdS nanorods (NRs) and Bi2MoO6 nanosheets (NSs), the migration of photogenerated electron-hole pairs along the stepped path was achieved. The ternary CPB samples were characterized by various analytical techniques, and their photocatalytic performance was investigated by conducting simulated fuel denitrification under visible-light irradiation. It was found that the CPB-4 composites exhibited the highest pyridine degradation activity, which reached 94% after 4 h of visible-light irradiation. The superior photocatalytic performance of the CPB-4 composite could be attributed to the synergistic effect of the Pt NPs and Bi2MoO6 NRs on the photocatalytic degradation as well as to the introduction of Pt and Bi2MoO6, which led to an excellent response and large specific surface area of the CPB-4 composite. Lastly, the bridging role of the Pt NPs introduced into the S-scheme system was also notable, as it effectively improved the separation and transfer of the CdS/Bi2MoO6 interfaces for the photogenerated electron-hole pairs while retaining strong redox ability.

A critical review on bismuth oxyhalide based photocatalysis for pharmaceutical active compounds degradation: Modifications, reactive sites, and challenges

Pharmaceutical active compounds (PhACs), as a kind of widely used pharmaceutical drugs, has attracted much attention. The bismuth oxyhalides (BiOX)-based photocatalysis can remove PhACs efficiently due to its unique layered structure, optical and electronic properties. Nevertheless, the rapid recombination of photogenerated electron-hole pairs, and the inherent instability of structure have limited its practical application. In order to solve these problems, recent modification studies tend to focus on facet control, elemental doping, bismuth-rich strategies, defect engineering and heterojunction. Therefore, the objective of this review is to summarize the recent developments in multiply modified strategies for PhACs degradation. The synthesis methods, photocatalytic properties and the enhancement mechanism are elaborated. Besides, based on theoretical calculation, the reactive sites of typical PhACs attacked by different reactive oxygen species were also proposed. Subsequently, challenges and opportunities in applications are also featured which include factors, viz., dissolution of halogen ions, instability under visible light, applications of real water/wastewater, intermediates and byproducts toxicity analysis of BiOX-based photocatalysis. Finally, the perspectives of BiOX-based photocatalysis for PhACs photodegradation in actual water applications are highlighted.

Bismuth oxychloride-based materials for the removal of organic pollutants in wastewater

Various kind of organics are toxic and detrimental, resulting in eutrophication, black, odorous water and so on. Photocatalysis has been deemed to be a promising technology which can decompose different kinds of organic pollutants under visible light irradiation, finally achieving non-poisonous, harmless CO2, water and other inorganic materials. Bismuth oxychloride (BiOCl) is considered as a promising photocatalyst for the efficient degradation of organic pollutants due to its high chemical stability, unique layered structure, resistance to corrosion and favorable photocatalytic property. However, BiOCl can only absorb UV irradiation because of its wide band gap of 3.2 eV-3.5 eV that limits its photocatalytic performance. Herein, a lot of methods have been reviewed to improve its photocatalytic activity. We introduced the unique and special layered structure of BiOCl, the typical and common synthesis methods that can control the morphology, and the most important part is varies of modification routes of BiOCl and the application of BiOCl-based materials for photocatalytic degradation of organic pollutants. Besides, we summarized the crucial issues and perspectives about the application of BiOCl in pollution management.

Instantaneous oxidation of levofloxacin as toxic pharmaceutical residuals in water using clay nanotubes decorated by ZnO (ZnO/KNTs) as a novel photocatalyst under visible light source

Kaolinite nanotubes were synthesized by a simple scrolling process and decorated by ZnO nanoparticles as a novel nanocomposite (ZnO/KNTs). The synthetic ZnO/KNTs composite was characterized as an effective photocatalyst in the oxidation of levofloxacin pharmaceutical residuals in the water resources. The composite displays a surface area of 95.4 m²/g, average pore diameter of 5.8 nm, and bandgap energy of 2.12 eV. It is of high catalytic activity in the oxidation of levofloxacin in the presence of visible light source. The complete oxidation for 10 mg/L of levofloxacin was recognized after 55 min, 45 min, and 30 min with applying 30 mg, 40 mg, and 50 mg of ZnO/KNTs as catalyst dosage, respectively. Additionally, it achieved complete oxidation for 20 mg/L and 30 mg/L of levofloxacin after 45 min and 75 min, respectively using 50 mg as catalyst dosage. The degradation efficiency was confirmed by detecting the residual TOC after the treatment tests and the formed intermediate compounds were identified to suggest the degradation pathways. In addition to the oxidation pathway, the mechanism was evaluated based on the active trapping tests that proved the dominance of hydroxyl radicals as the essential active species. Finally, the ZnO/KNTs composite is of promising recyclability properties and achieved better results than several studied photocatalysts in literature.

MnCeOX with high efficiency and stability for activating persulfate to degrade AO7 and ofloxacin

An efficient MnCeO_x composite was successfully synthesized for activation of persulfate to degrade acid orange 7 (AO7) and ofloxacin. Pollutants degradation efficiencies with different catalytic systems were investigated. Results showed the performance of MnCeO_x was better than MnO_x, CeO₂ and MnO_x + CeO₂. Thus, there was a clear synergistic effect (Se) between Mn and Ce in the composite, and the Se was 73.8% for AO7 and 39.6% for ofloxacin. In addition, AO7 removal fitted 1st order reaction while ofloxacin removal fitted 2nd order reaction in MnCeO_x/persulfate system. Moreover, MnCeO_x/persulfate system showed high efficiency in pH range of 5-9. Mechanism analysis showed that SO₄^- and OH on the surface of the catalyst were the main active species, and O₂^- also played an important role in pollutants degradation. Furthermore, MnCeO_x showed high activity in actual water. Finally, the possible degradation pathway of ofloxacin was proposed according to the high performance liquid chromatography-mass spectrometry result. Overall, this study provides an efficient and stable catalyst to activate persulfate to degrade refractory pollutants.

Pd/BiOBr tetragonal platelets with controllable facets by the decoration of La dopant enabling highly efficient photocatalytic activity

Pd particles deposited on BiOBr caused instability of the crystal structure; however, La can stabilize the crystal structure during the deposition of Pd particles.

Highly dispersed BiOCl decahedra with a highly exposed (001) facet and exceptional photocatalytic performance

BiOCl has been identified to be a promising photocatalyst for the rapid photodegradation of organic pollutants, but its practical application was restricted by its limited photocatalytic activity. In this work, a highly reactive BiOCl decahedron photocatalyst with an exposed (001) facet was successfully hydrothermally synthesized via a simple hydrothermal method using bismuth nitrate (Bi(NO3)3·5H2O) and ammonium chloride (NH4Cl) as raw materials. By adjusting the dosage of NH4Cl, the BiOCl nanoplates transformed from hexahedra with quadrilateral {110} oblique facets to decahedra with octagonal {110} and {100} oblique facets. As compared to the original BiOCl nanoplates, decahedral BiOCl possesses much more oxygen-enriched surfaces and a narrowed bandgap, resulting in enhanced photocatalytic performance. The decahedral BiOCl photocatalyst achieves a high degradability of 98% for the photodegradation of RhB after 6 min of irradiation, which is much faster than that of a hexahedral BiOCl sample.