Chemical modification of tannins from Acacia mearnsii to produce formaldehyde free flocculant

Phosphorylating Tannin in Urea System: A Simple Approach for Enhanced Methylene Blue Removal from Aqueous Media

Tannin, after lignin, is one of the most abundant sources of natural aromatic biomolecules. It has been used and chemically modified during the past few decades to create novel biobased materials. This work intended to functionalize for the first time quebracho Tannin (T) through a simple phosphorylation process in a urea system. The phosphorylation of tannin was studied by Fourier transform infrared spectroscopy (FTIR), NMR, inductively coupled plasma optical emission spectroscopy (ICP-OES), and X-ray fluorescence spectrometry (XRF), while further characterization was performed by scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDX) and thermogravimetric analysis (TGA) to investigate the morphology, composition, structure, and thermal degradation of the phosphorylated material. Results indicated the occurrence of phosphorylation, suggesting the insertion of phosphate-containing groups into the tannin structure, revealing a high content of phosphate for modified tannin (PT). This elevated phosphorus content serves as evidence for the successful incorporation of phosphate groups through the functionalization process. The corresponding PT and T were employed as adsorbents for methylene blue (MB) removal from aqueous solutions. The results revealed that the Langmuir isotherm model effectively represents the adsorption isotherms. Additionally, the pseudo-second-order model indicates that chemisorption predominantly controls the adsorption mechanism. This finding also supports the fact that the introduced phosphate groups via the phosphorylation process significantly contributed to the improved adsorption capacity. Under neutral pH conditions and at room temperature, the material achieved an impressive adsorption capacity of 339.26 mg·g-1 in about 2 h.

A quaternary ammonium salt grafted tannin-based flocculant boosts the conjugative transfer of plasmid-born antibiotic resistance genes: The nonnegligible side of their flocculation-sterilization properties

This study developed dual-function tannin-based flocculants, namely tannin-graft-acrylamide-diallyl dimethyl ammonium chloride (TGCC-A/TGCC-C), endowed with enhanced flocculation-sterilization properties. The impacts of these flocculants on proliferation and transformation of antibiotic resistance genes (ARGs) among bacteria during the flocculation-deposition process were examined. TGCC-A/TGCC-C exhibited remarkable flocculation capacities towards both Escherichia coli and Staphylococcus aureus, encompassing a logarithmic range of initial cell density (108-109 CFU/mL) and a broad pH spectrum (pH 2-11). The grafted quaternary ammonium salt groups played pivotal parts in flocculation through charge neutralization and bridging mechanisms, concurrently contributing to sterilization by disrupting cellular membranes. The correlation between flocculation and sterilization entails a sequential progression, where an excess of TGCC, initially employed for flocculation, is subsequently consumed for sterilization purposes. The frequencies of ARGs conjugative transfer were enhanced in bacterial flocs across all TGCC treatments, stemming from augmented bacterial aggregation and cell membrane permeability, elicited stress response, and up-regulated genes encoding plasmid transfer. These findings underscore the indispensable role of flocculation-sterilization effects in mediating the propagation of ARGs, consequently providing substantial support for the scientific evaluation of the environmental risks associated with flocculants in the context of ARGs dissemination during the treatment of raw water featuring high bacterial density.

A new efficient tannin-based flocculant made by a new modification idea: multiple rounds of Mannich reaction with aminated tannins as ammonia chloride

This research provided a new modification idea and made a new high-efficiency plant-based flocculant through the three rounds of reactions using tannin, formaldehyde, and ammonia chloride. Tannins as a concerned natural flocculant are mainly through a round of Mannich reaction to cationic modification now. This research provided a new cationic modification idea with the three rounds of Mannich reactions to obtain a modified tannin with a larger molecular weight and more complex structure. The synthesis and flocculation tests were conducted to study the effects of rounds of reaction, reactants ratio, reaction time of each round, and pH on the flocculation ability of the synthetically modified tannins. The increased flocculation capacity of modified tannins occurred with the increased rounds of reactions by increasing the electric neutralization and bridging capacity. The results of this research showed the increased flocculation capacity of the modified tannins with the increased ratio ((formaldehyde or ammonium chloride)/tannin). The flocculation capacity of the modified tannins is the greatest in the appropriate reaction time of each round (4 + 4 h) and pH (pH = 2). According to model fitting, the optimal synthesis condition is 1:6.094:6.094, 7.092 h, and pH = 2.476, which has been tested experimentally. The new modification idea and new high-efficiency modified tannin are very meaningful to the application of environmentally friendly flocculants and to solve the disadvantages of traditional chemical flocculants.

Creating coagulants through the combined use of ash and brine

Sludge incineration and seawater desalination are two approaches that can be used in the disposal of waste activated sludge (WAS) and for obtaining fresh water. As resource recovery from wastewater treatment and water purification is a topic of particular interest in these times, "water mining" has become a focus of research, with phosphate/P-recovery from WAS incineration ash, and extraction of useful elements from the brine of desalination being important steps in the pursuit of a circular/blue economy. However, P-recovery from ash involves removing metals, which need to be disposed of carefully, as does the brine collected. If cations in the ash and anions in the brine could be combined in order to produce coagulants/flocculants, a new circular model would be established. A preliminary experiment for this purpose has demonstrated that a liquid poly‑aluminum chloride (PAC) could be synthesized from the aluminum ion/Al³⁺ removed from the ash and the original brine. With this work, we synthesized the liquid PAC by a hydrothermal method, and the results from infrared spectrometer demonstrated that the synthesized PAC was similar to a commercial PAC. Moreover, the synthesized PAC was able to efficiently reduce the effluent turbidity of wastewater treatment plants (WWTPs), especially when compared with the commercial PAC. It is therefore important that research in this area be continued in order to improve the quality of synthesized coagulants and to produce different coagulants based on cations and anions in ash and brine.

Optimization of Microalgal Harvesting with Inorganic and Organic Flocculants Using Factorial Design of Experiments

Microalgae have a lot of potential as a source of several compounds of interest to various industries. However, developing a sustainable and efficient harvesting process on a large scale is still a major challenge. This is particularly a problem when the production of low-value products is intended. Chemical flocculation, followed by sedimentation, is seen as an alternative method to improve the energetic and economic balance of the harvesting step. In this study, inorganic (aluminum sulfate, ferric sulfate, ferric chloride) and organic (Zetag 8185, chitosan, Tanfloc SG) flocculants were tested to harvest Chlorella vulgaris in batch mode. Preliminary assays were conducted to determine the minimum dosages of each flocculant that generates primary flocs at different pH. Except for chitosan, the organic flocculants required small dosages to initiate floc formation. Additional studies were performed for the flocculants with a better performance in the preliminary assays. Zetag 8185 had the best results, reaching 98.8% and 97.9% efficiencies with dosages of 50 and 100 mg L−1, respectively. Lastly, a 24 full factorial design experiment was performed to determine the effects of the flocculant dosage, settling time, and mixing time on the Zetag 8185 harvesting efficiency. The harvesting efficiency of C. vulgaris was optimal at a dosage of 100 mg L−1 and 3 min of rapid mixing.

Tannin-based coagulants: Current development and prospects on synthesis and uses

Population growth, industrialization, urbanization, and agriculture lead to a decrease in the availability of clean water. Coagulation/flocculation is one of the most common operations in water, urban wastewater, and industrial effluents treatment systems. Usually, this process is achieved using conventional coagulants that have their performance affected by pH, are poorly biodegradable, produce a huge volume of sludge, and are associated with degenerative diseases. As a substitute for these chemicals, natural coagulants have been highly researched for the last ten/fifteen years, especially the tannin-based (TB) ones. This review paper highlights the advantages of using these greener products to treat different types of water, wastewater, and effluents, especially from dairy, cosmetics, laundries, textile, and other industries. TB coagulants can successfully remove turbidity, color, suspended solids, soluble organic (chemical/biochemical oxygen demand) and inorganic matter (total phosphate, and heavy metals), and microorganisms. TB coagulants are compatible with other treatment technologies and can be used as coagulant-aid to reduce the consumption of chemicals. TB coagulants can reduce operating costs of water treatment due to less alkalinity consumption, as pH adjustment is sometimes unnecessary, and the production of a smaller volume of biodegradable sludge. TB coagulants can be synthesized by valorizing wastes/by-products, from the bark of some specific trees and skins/pomace of different fruits and vegetables. The strengths, weaknesses, opportunities, and threats (SWOT) on TB coagulants are discussed. The progress of TB coagulants is promising, but some threats should be overcome, especially on tannin extraction and cationization. The market competition with conventional coagulants, the feasibility of application in real waters, and the reluctance of the industries to adapt to new technologies are other weaknesses to be surpassed.

A novel co-graft tannin-based flocculant for the mitigation of harmful algal blooms (HABs): The effect of charge density and molecular weight

In this study, for the first time, we developed a series of co-graft tannin-based flocculants, TA-g-P(AM-DMDAAC), with different charge densities (CDs) and molecular weights (MWs) and evaluated their algal-removal performances. The effects of TA-g-P(AM-DMDAAC) on the cell integrity of Microcystis aeruginosa and release of extracellular organic matter (EOM) and microcystin-leucine-arginine (MC-LR) in flocculation and floc storage were also studied. Results suggested that TA-g-P(AM-DMDAAC) could not only efficiently remove algal cells over a wide pH range (pH 3-11) but also EOM. CD and MW significantly affected flocculation performance and floc characteristics of TA-g-P(AM-DMDAAC). A higher CD helped achieve a higher removal efficiency of algal cells and EOM, whereas a higher MW resulted in the formation of larger and more compact flocs. Furthermore, the larger and denser flocs could better protect algal cells and reduce the release of EOM during floc storage. Notably, algal cells in the TA-g-P(AM-DMDAAC) flocs did not appear to show signs of massive rupture nor did they release EOM and MC-LR extensively for at least 20 days of storage. The abundance and easy availability of tannin resources effectively reduce the cost of preparing tannin-based flocculants. Therefore, TA-g-P(AM-DMDAAC) can have broad application prospects in the management of cyanobacteria bloom.

The use of natural organic flocculants for harvesting microalgae grown in municipal wastewater at different culture densities

Harvesting microalgae from liquid culture is a difficult issue to solve and is most commonly done through settling. However, settling is a slow process on its own and generally needs to be induced chemically or by introducing stress to the culture. Polymeric, cationic substances, such as cationised starch and chitosan, are often used for flocculation and settling. These large, positively charged molecules form large clusters with suspended particles in the liquid medium. In the present study, three natural organic flocculants (cationic starch, chitosan and acacia tannin S5T) were tested to harvest microalgal cultures grown in wastewater. Two microalgal species, one strain of Chlorella vulgaris and one strain of Scenedesmus obliquus, were cultured in municipal wastewater for different lengths of time, and settled using either cationic starch, chitosan or acacia tannin S5T. Results indicated that S5T worked with approximately the same efficiency in the two assayed species, although it requires a relatively high dosage to function (about 300 mg L^-1 ), while the other two flocculants varied from species to species.