High-performance low-cost solar collectors for water treatment fabricated with recycled materials, open-source hardware and 3d-printing technologies

Photocatalysts for a sustainable future: Innovations in large-scale environmental and energy applications

The growing environmental and energy crises have prompted researchers to seek new solutions, including large-scale photocatalytic environmental remediation and the production of solar hydrogen using photocatalytic materials. To achieve this goal, scientists have developed numerous photocatalysts with high efficiency and stability. However, the large-scale application of photocatalytic systems under real-world conditions is still limited. These limitations arise at every step, including the large-scale synthesis and deposition of photocatalyst particles on a solid support, and the development of an optimal design with high mass transfer and efficient photon absorption. The purpose of this article is to provide a detailed description of the primary challenges and potential solutions encountered in scaling up photocatalytic systems for use in large-scale water and air purification and solar hydrogen production. Additionally, based on a review of current pilot developments, we draw conclusions and make comparisons regarding the main operating parameters that affect performance, as well as propose strategies for future research.

Reduction of CO2 emission through a photocatalytic process using powder and coated zeolite-supported TiO2 under concentrated sunlight irradiation

The efficiency of a novel synthetic zeolite (Ze) prepared from stone cutting sludge and a natural zeolite (clinoptilolite, Cp) as the support of TiO₂ photocatalyst was examined for the CO₂ removal under solar irradiation using a designed parabolic trough collector (PTC). The used samples were characterized using XRF, BET, SEM/EDS, and XPS analyses. The enhanced sunlight irradiation obtained by PTC increased the performance of CO₂ photocatalytic removal. The maximum CO₂ adsorption by TiO₂-Ze and TiO₂-Cp composites was 21.1% and 28.4% which increased to 61.8% and 78.9% under sunlight irradiation, respectively. The efficiency of zeolite-TiO₂ composites for CO₂ removal was approximately two times higher than zeolites and TiO₂ alone. The performance of TiO₂-Ze-coated composite with lower use of photocatalyst for CO₂ adsorption and photocatalytic removal was better than that of powder one. Regeneration of TiO₂-Ze using NaOH solution improved its removal efficiency. The adsorption behavior of CO₂ on TiO₂-Ze composite was well described by the Langmuir isotherm and the pseudo-first-order kinetic model. This work promises CO₂ reduction using natural and synthetic zeolite as an efficient photocatalyst support under solar irradiation.

Possibilities and Limitations of the Sono-Fenton Process Using Mid-High-Frequency Ultrasound for the Degradation of Organic Pollutants

Mid-high-frequency ultrasound (200-1000 kHz) eliminates organic pollutants and also generates H₂O₂. To take advantage of H₂O₂, iron species can be added, generating a hybrid sono-Fenton process (sF). This paper presents the possibilities and limitations of sF. Heterogeneous (a natural mineral) and homogeneous (Fe²⁺ and Fe³⁺ ions) iron sources were considered. Acetaminophen, ciprofloxacin, and methyl orange were the target organic pollutants. Ultrasound alone induced the pollutants degradation, and the dual competing role of the natural mineral (0.02-0.20 g L^-1) meant that it had no significant effects on the elimination of pollutants. In contrast, both Fe²⁺ and Fe³⁺ ions enhanced the pollutants' degradation, and the elimination using Fe²⁺ was better because of its higher reactivity toward H₂O₂. However, the enhancement decreased at high Fe²⁺ concentrations (e.g., 5 mg L^-1) because of scavenger effects. The Fe²⁺ addition significantly accelerated the elimination of acetaminophen and methyl orange. For ciprofloxacin, at short treatment times, the degradation was enhanced, but the pollutant complexation with Fe³⁺ that came from the Fenton reaction caused degradation to stop. Additionally, sF did not decrease the antimicrobial activity associated with ciprofloxacin, whereas ultrasound alone did. Therefore, the chemical structure of the pollutant plays a crucial role in the feasibility of the sF process.

Fabrication and Application of Photocatalytic Composites and Water Treatment Facility Based on 3D Printing Technology

Currently, the degradation of organic pollutants in wastewater by photocatalytic technology has attracted great attention. In this study, a new type of 3D printing material with photocatalytic activity was first prepared to print a water treatment equipment, and then a layer of silver-loaded TiO2 was coated on the equipment to further improve the catalytic degradation performance. The composite filaments with a diameter of 1.75 ± 0.05 mm were prepared by a melt blending method, which contained 10 wt% of modified TiO2 and 90 wt% of PLA. The silver-loaded TiO2 was uniformly coated on the equipment through a UV-curing method. The final results showed that those modified particles were uniformly dispersed in the PLA matrix. The stable printing composite filaments could be produced when 10 wt% TiO2 was added to the PLA matrix. Moreover, the photocatalytic degradation performance could be effectively improved after 5 wt% of silver loading was added. This novel facility showed good degradability of organic compounds in wastewater and bactericidal effect, which had potential applications for the drinking water treatment in the future.

Solar Water Disinfection to Produce Safe Drinking Water: A Review of Parameters, Enhancements, and Modelling Approaches to Make SODIS Faster and Safer

Solar water disinfection (SODIS) is one the cheapest and most suitable treatments to produce safe drinking water at the household level in resource-poor settings. This review introduces the main parameters that influence the SODIS process and how new enhancements and modelling approaches can overcome some of the current drawbacks that limit its widespread adoption. Increasing the container volume can decrease the recontamination risk caused by handling several 2 L bottles. Using container materials other than polyethylene terephthalate (PET) significantly increases the efficiency of inactivation of viruses and protozoa. In addition, an overestimation of the solar exposure time is usually recommended since the process success is often influenced by many factors beyond the control of the SODIS-user. The development of accurate kinetic models is crucial for ensuring the production of safe drinking water. This work attempts to review the relevant knowledge about the impact of the SODIS variables and the techniques used to develop kinetic models described in the literature. In addition to the type and concentration of pathogens in the untreated water, an ideal kinetic model should consider all critical factors affecting the efficiency of the process, such as intensity, spectral distribution of the solar radiation, container-wall transmission spectra, ageing of the SODIS reactor material, and chemical composition of the water, since the substances in the water can play a critical role as radiation attenuators and/or sensitisers triggering the inactivation process.