Application of lead oxide electrodes in wastewater treatment: A review

Increased energy efficiency using pulse-potential electrochemical advanced oxidation processes

The research investigated the pulse potential effect on Electrochemical Advanced Oxidation Processes (EAOPs) for benzoic acid oxidation. The current efficiency of the electrooxidation is enhanced by changing the pulse frequency and potential on electrodes. The experiments showed that there are opposing phenomena affecting energy efficiency. On the one hand, pulse potential accelerates the mass transfer of benzoic acid in an electric field. On the other hand, pulse potential increases the non-faradic current that uses energy without causing oxidation. Using the Sand equation and the electric double-layer theory, we optimized the pulse frequency and voltage amplitude to achieve the highest energy efficiency for the pulse potential EAOPs. Compared with DC (Direct current) EAOPs, the pulse potential EAOPs save 50% EE/O and have a 41 % CE for the 4_2 V cycle at 50 Hz. Therefore, pulse potential EAOPs can achieve both high pollutant degradation efficiency and low energy consumption at the same time.

Detection and treatment of mono and polycyclic aromatic hydrocarbon pollutants in aqueous environments based on electrochemical technology: recent advances

Mono and polycyclic aromatic hydrocarbons are widely distributed and severely pollute the aqueous environment due to natural and human activities, particularly human activity. It is crucial to identify and address them in order to reduce the dangers and threats they pose to biological processes and ecosystems. In the fields of sensor detection and water treatment, electrochemistry plays a crucial role as a trustworthy and environmentally friendly technology. In order to accomplish trace detection while enhancing detection accuracy and precision, researchers have created and studied sensors using a range of materials based on electrochemical processes, and their results have demonstrated good performance. One cannot overlook the challenges associated with treating aromatic pollutants, including mono and polycyclic. Much work has been done and good progress has been achieved in order to address these challenges. This study discusses the mono and polycyclic aromatic hydrocarbon sensor detection and electrochemical treatment technologies for contaminants in the aqueous environment. Additionally mentioned are the sources, distribution, risks, hazards, and problems in the removal of pollutants. The obstacles to be overcome and the future development plans of the field are then suggested by summarizing and assessing the research findings of the researchers.

Material Design Strategies for Recovery of Critical Resources from Water

Population growth, urbanization, and decarbonization efforts are collectively straining the supply of limited resources that are necessary to produce batteries, electronics, chemicals, fertilizers, and other important products. Securing the supply chains of these critical resources via the development of separation technologies for their recovery represents a major global challenge to ensure stability and security. Surface water, groundwater, and wastewater are emerging as potential new sources to bolster these supply chains. Recently, a variety of material-based technologies have been developed and employed for separations and resource recovery in water. Judicious selection and design of these materials to tune their properties for targeting specific solutes is central to realizing the potential of water as a source for critical resources. Here, the materials that are developed for membranes, sorbents, catalysts, electrodes, and interfacial solar steam generators that demonstrate promise for applications in critical resource recovery are reviewed. In addition, a critical perspective is offered on the grand challenges and key research directions that need to be addressed to improve their practical viability.

Elaboration of Highly Modified Stainless Steel/Lead Dioxide Anodes for Enhanced Electrochemical Degradation of Ampicillin in Water

Lead dioxide-based electrodes have shown a great performance in the electrochemical treatment of organic wastewater. In the present study, modified PbO2 anodes supported on stainless steel (SS) with a titanium oxide interlayer such as SS/TiO2/PbO2 and SS/TiO2/PbO2-10% Boron (B) were prepared by the sol–gel spin-coating technique. The morphological and structural properties of the prepared electrodes were characterized by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray photoelectron spectroscopy (XPS). It was found that the SS/TiO2/PbO2-10% B anode led to a rougher active surface, larger specific surface area, and therefore stronger ability to generate powerful oxidizing agents. The electrochemical impedance spectroscopy (EIS) measurements showed that the modified PbO2 anodes displayed a lower charge transfer resistance Rct. The influence of the introduction of a TiO2 intermediate layer and the boron doping of a PbO2 active surface layer on the electrochemical degradation of ampicillin (AMP) antibiotic have been investigated by chemical oxygen demand measurements and HPLC analysis. Although HPLC analysis showed that the degradation process of AMP with SS/PbO2 was slightly faster than the modified PbO2 anodes, the results revealed that SS/TiO2/PbO2-10%B was the most efficient and economical anode toward the pollutant degradation due to its physico-chemical properties. At the end of the electrolysis, the chemical oxygen demand (COD), the average current efficiency (ACE) and the energy consumption (EC) reached, respectively, 69.23%, 60.30% and 0.056 kWh (g COD)−1, making SS/TiO2/PbO2-10%B a promising anode for the degradation of ampicillin antibiotic in aqueous solutions.

Treatment of thiocyanate-containing wastewater: a critical review of thiocyanate destruction in industrial effluents

Thiocyanate is a common pollutant in gold mine, textile, printing, dyeing, coking and other industries. Therefore, thiocyanate in industrial wastewater is an urgent problem to be solved. This paper reviews the chemical properties, applications, sources and toxicity of thiocyanate, as well as the various treatment methods for thiocyanate in wastewater and their advantages and disadvantages. It is emphasized that biological systems, ranging from laboratory to full-scale, are able to successfully remove thiocyanate from factories. Thiocyanate-degrading microorganisms degrade thiocyanate in autotrophic manner for energy, while other biodegrading microorganisms use thiocyanate as a carbon or nitrogen source, and the biochemical pathways and enzymes involved in thiocyanate metabolism by different bacteria are discussed in detail. In the future, degradation mechanisms should be investigated at the molecular level, with further research aiming to improve the biochemical understanding of thiocyanate metabolism and scaling up thiocyanate degradation technologies from the laboratory to a full-scale.

Electrochemical paraquat sensor based on lead oxide nanoparticles

1,1-Dimethyl-4,4-bipyridinium dichloride known as paraquat is a popular well-known herbicide that is widely used in agriculture around the world. However, paraquat is a highly toxic chemical causing damage to vital organs including the respiratory system, liver, heart, and kidneys and death. Therefore, detection of paraquat is still necessary to protect life and the environment. In this work, an electrochemical sensor based on lead oxide nanoparticles (PbO-NPs) modified on a screen-printed silver working electrode (SPE) has been fabricated for paraquat detection at room temperature. The PbO-NPs have been synthesized by using a sparking method via two Pb metal wires. The electrochemical paraquat sensors have been prepared by a simple drop-casting of PbO-NPs solution on the surface of the SPE. The PbO-NPs/SPE sensor exhibits a linear response in the range from 1 mM to 5 mM with good reproducibility and high sensitivity (204.85 μA mM⁻¹ cm⁻²) for paraquat detection at room temperature. The PbO-NPs/SPE sensor shows high selectivity to paraquat over other popular herbicides such as glyphosate, glufosinate-ammonium and butachlor-propanil. The application of the PbO-NPs/SPE sensor is also demonstrated via the monitoring of paraquat contamination in juice and milk.

The PbO nanoparticles-based electrochemical sensor can be integrated into a smartphone for on-site field testing of paraquat with high sensitivity and selectivity.