An in vitro evaluation of the effect of polishing on the stainability of different CAD/CAM ceramic materials

The impact of Streptococcus mutans biofilms on the color stability and topographical features of three lithium disilicate ceramics

PURPOSE

Secondary caries around ceramic restorations is the most common reason for the replacement of fixed dental prostheses (FDPs). Therefore, it is important to examine the susceptibility of different ceramic materials to biofilm formation. This study aimed to evaluate biofilm development and associated roughness and color alterations in three lithium disilicate ceramics: Emax CAD (EC), Emax Press (EP), and LiSi Press (LP).

MATERIALS AND METHODS

Streptococcus mutans biofilms were grown on the three ceramics (n = 10 per group) for 7 days. Surface roughness values and color alteration were assessed before and after the biofilm using a non-contact profilometer and spectrophotometer, respectively. Biofilm growth was evaluated using colony-forming units (CFUs) and scanning electron microscope (SEM) images. The data were analyzed using one-way ANOVA and Tukey tests.

RESULTS

There was a significant (p ≤ 0.001) growth of S. mutans colonies on EC (6.75 ± 0.56) and EP (6.72 ± 0.54) specimens compared to LP, which showed no biofilm growth. The change in average surface roughness (∆Ra, nm) was significantly lower (p < 0.001) in the EC specimens (0.029 ± 0.003) compared to the EP (0.055 ± 0.012) and LP (0.041 ± 0.010). When the changes in the Rv and Rt values were investigated, no significant difference was observed among the groups. Following the biofilm challenge, the change in color (∆E00) was significantly lower (p = 0.005) in the LP group (1.68 ± 1.45) compared to the EC group (3.89 ± 1.50) and no significant difference was observed between the EP group (2.74 ± 1.01) and the other two ceramics (p ≥ 0.05).

CONCLUSION

LP ceramics exhibited superior resistance to S. mutans biofilm formation and associated changes in surface roughness and color compared to the Emax CAD and Emax Press ceramics. These findings suggest that the LiSi Press material may be more favorable to mitigate the risk of secondary caries.

Effect of polishing and bleaching on color, whiteness, and translucency of CAD/CAM monolithic materials

OBJECTIVE

To evaluate the effect of polishing and bleaching on the recovery of lightness, color, whiteness, and relative translucency parameter (RTP) in CAD/CAM materials and changes in these properties when another staining in coffee was conducted after the treatments.

MATERIALS AND METHODS

Disks of Lava Ultimate (LU), Vita Enamic (VE), IPS Empress CAD (EMP), IPS e.max CAD (EMAX), and Vita Suprinity (VS) were (1) not treated (control), (2) polished with Proxyt or (3) Ceramisté, (4) bleached with Opalescence PF or (5) Whiteness HP Blue, and (6) air polished with Clinpro Prophy Powder. CIE L*a*b* color coordinates were registered at baseline (R0), after staining with coffee for 30 min daily for 36.5 days and treatment (R1), and after another staining (R2). Differences (R1-R0 and R2-R0) in lightness (ΔL00), color (ΔE00), RTP (ΔRTP00), and whiteness (ΔWID) were evaluated by mixed repeated measures ANOVA and 95% confidence intervals (α = 0.05) and interpreted in function of their respective 50:50% PT and AT thresholds. Topography was evaluated by scanning electron microscopy (SEM).

RESULTS

In LU, Opalescence PF and Proxyt decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {\mathrm{R}}_0\right)} $$ , andΔWI D R 1 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_1\hbox{--} {R}_0\right)} $$ and showed lowerΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ , andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ . In VE, all treatments decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , andΔWI D R 1 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_1\hbox{--} {R}_0\right)} $$ , whereasΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ , andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ were lower in Opalescence PF than in the control group. In both moments, ΔE00 and ΔWID in EMP (also ΔL00) and EMAX were higher in Opalescence PF than in the control group, from which the other treatments did not differ in R1-R0. In EMP,Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ in Whiteness HP Blue (alsoΔ L 00 R 2 - R 0 $$ {\Delta L}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ ) and Proxyt were also higher in comparison to the control group and in VS, Ceramisté decreasedΔ L 00 R 1 - R 0 $$ {\Delta L}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ ,Δ E 00 R 1 - R 0 $$ {\Delta E}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , andΔ R T P 00 R 1 - R 0 $$ \varDelta RT{P}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ , whereas Opalescence PF increasedΔRTP 00 R 1 - R 0 $$ {\Delta \mathrm{RTP}}_{00\left({R}_1\hbox{--} {R}_0\right)} $$ .Δ E 00 R 2 - R 0 $$ {\Delta E}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ of Ceramisté andΔWI D R 2 - R 0 $$ {\Delta \mathrm{WI}}_{\mathrm{D}\left({R}_2\hbox{--} {R}_0\right)} $$ andΔ R T P 00 R 2 - R 0 $$ \varDelta RT{P}_{00\left({R}_2\hbox{--} {R}_0\right)} $$ of Proxyt were lower than those of the control group.

CONCLUSIONS

The most suitable treatment to recover the lightness, color, whiteness, and RTP without changing these properties after another coffee exposure is material-dependent.

CLINICAL SIGNIFICANCE

Although the effectiveness of the treatment was material-dependent, Proxyt was the only treatment that promoted clinically acceptable changes for both LU and VE, while for purely ceramic materials, this condition was observed with Ceramisté and Clinpro Prophy Powder.

The effect of repair protocols and chewing simulation on the microtensile bond strength of two resin matrix ceramics to composite resin

BACKGROUND

To assess the micro tensile bond strength (µTBS) of two resin matrix ceramic (RMC) blocks bonded to composite resin by using different repair protocols with and without chewing simulation (CS).

MATERIALS AND METHODS

Two resin matrix ceramic blocks (Vita Enamic and Lava Ultimate) were divided into 4 groups according to the surface treatments: Bur grinding (control), Bur grinding + silane, 9.5% HF acid etching, and 9.5% HF acid etching + silane. The single bond universal adhesive was applied on all specimens after the surface treatments according to the manufacturer's instructions, it was administered actively on the treated surface for 20 s and then light cured for 10 s, followed by incremental packing of composite resin to the treated surface. Each group was further divided into 2 subgroups (with/without chewing simulation for 500,000 cycles). A micro tensile bond strength test was performed for each group (n = 15). The effect of surface treatments on the materials was examined by using a scanning electron microscope (SEM). The micro tensile bond strength (MPa) data were analyzed with a three-way ANOVA, the independent t-test, and one-way ANOVA followed by the Tukey post-hoc test.

RESULTS

µTBS results were significantly higher for Lava Ultimate than Vita Enamic for all the surface treatment protocols with (p < 0.01). The chewing simulation significantly negatively affected the micro-tensile bond strength (p < 0.001). Bur grinding + saline exhibited the highest bond strength values for Lava Ultimate, both with and without chewing simulation. For Vita Enamic, bur grinding + saline and HF acid + saline showed significantly higher bond strength values compared to other surface treatments, both with and without chewing simulation (p ≤ 0.05).

CONCLUSION

Bur grinding + silane could be recommended as a durable repair protocol for indirect resin matrix ceramics blocks with composite resin material.

Color stability and surface roughness of resin-ceramics with different surface treatments: A systematic review and meta-analysis of in vitro studies

STATEMENT OF PROBLEM

Surface treatments for resin-ceramics have been developed to obtain a smooth surface and improve color stability. However, a consensus on the best treatment for these materials is lacking.

PURPOSE

The purpose of this systematic review and meta-analysis was to evaluate the color stability and roughness of glass-ceramics versus resin-ceramics with different surface treatments.

MATERIAL AND METHODS

The preferred reporting items for systematic reviews and meta-analyses (PRISMA) guidelines were followed, and the study was registered in the open science framework (OSF) for in vitro studies. The population, intervention, control, and outcome (PICO) question was "Is there a difference in color stability and roughness between resin-ceramic vs vitreous ceramics in different surface treatment protocols?" A literature search was performed in PubMed/MEDLINE, Embase, Web of Science, Scopus, Cochrane Library, and ProQuest databases up to January 2023. The Joanna Briggs Institute's critical assessment guidelines for quasi-experimental studies were used for quality assessment. The meta-analysis was based on the inverse variance (IV) method (α=.05).

RESULTS

A total of 18 laboratory studies were published between 2015 and 2022, with a total of 2160 specimens, all of which were analyzed qualitatively. The meta-analysis indicated significantly less optical alteration for lithium disilicate ceramics (P<.01; MD: 2.69; 95% CI: 2.00-3.39; I²=89%, P<.01), even when compared with resin-ceramics with polish or sealants (P<.01; MD: 2.45; 95% CI: 1.59-3.30; I²=87%, P<.01) and (P<.01; MD: 3.24; 95% CI: 2.02-4.47; I²=89%, P<.01), while there was no significant difference in surface roughness (P=.08; MD: -0.71; CI 95%: -1.52 to 0.09; I²=87%, P<.01) (P=.33; MD: -0.31; CI 95%: -0.94 to 0.32; I²=87%, P<.01), respectively.

CONCLUSIONS

Resin-ceramics that have been polished or treated with sealants have lower color stability than glazed glass-ceramics; however, they are similar in terms of surface roughness.

The Toothbrushing Effects on Surface Properties and Color Stability of CAD/CAM and Pressable Ceramic Fixed Restorations-An In Vitro Study

Pressable ceramic restorations have been introduced and investigated, and found comparable to CAD/CAM ceramic in terms of mechanical properties; however, the effect of toothbrushing on the pressable ceramic has not been thoroughly investigated. The objective of the current study was to assess the effect of artificial toothbrushing simulation on the surface roughness, microhardness, and color stability of different ceramic materials. Three lithium disilicate-based ceramics (IPS Emax CAD [EC], IPS Emax Press [EP]; (Ivoclar Vivadent AG), and LiSi Press [LP] (GC Corp, Tokyo, Japan)) were examined. For each ceramic material, eight bar-shaped specimens were prepared and subjected to 10,000 brushing cycles. Surface roughness, microhardness, and color stability (∆E) were measured before and after brushing. Scanning electron microscopy (SEM) was used for surface profile analysis. The results were analyzed using one-way ANOVA, Tukey's post hoc test, and paired sample t-test α = 0.05. The findings revealed a non-significant decrease in the surface roughness of EC, EP, and LP groups (p > 0.05), and both LP and EP have the lowest surface roughness values (0.64 ± 0.13, 0.64 ± 0.08 µm) after brushing, respectively. Toothbrushing showed a decrease in the microhardness of the three groups: EC and LP, p < 0.001; EP, p = 0.012). EP showed the lowest hardness value after brushing (862.45 ± 273.83). No significant changes (∆E) were observed in all groups (p > 0.05); however, the EC group was found to be considerably affected by color changes, in comparison to the EC and LP groups. Toothbrushing had no effect on surface roughness and color stability of all tested materials, but it decreased the microhardness. Material type, surface treatments, and glazing of ceramic materials contributed to the surface changes in the ceramic materials, necessitating further investigations in terms of the toothbrushing effect with different glazing as variables.

Comparison of the Degree of Staining of Computer-Aided Design-Computer-Aided Manufacture (CAD-CAM) Ceramic Veneers by Green Tea, Coffee, and Coca-Cola Using a Digital Spectrophotometer

BACKGROUND The majority of dental professionals currently recognize lithium disilicate E-max ceramic veneers as a the most widely used, conservative, and effective cosmetic materials in dentistry. This study aimed to compare the degree of surface changes - roughness (Ra), depth (Rz), and mean color changes (ΔE₀₀) - of computer-aided design-computer-aided manufactured (CAD/CAM) ceramic veneers materials of varying thicknesses caused by staining by green tea, coffee, and Coca-Cola using digital spectrophotometer. MATERIAL AND METHODS This study was conducted at King Khalid University, College of Dentistry. Lithium disilicate glass ceramic (LDGC) material was used to create 60 rectangular slices using the CAD/CAM system. The material thickness and the type of beverage were measured. The specimens were immersed in beverages according to the manufacturer's instructions. Specimen description and tomography were completed with a 3D noncontact surface metrology using interferometry. The "VITA Easy-Shade" spectrophotometer was used to measure ΔE₀₀. It was recorded after 2 weeks for different material thicknesses after immersing samples in green tea, coffee, and Coca-Cola staining materials.f RESULTS Significant changes in ceramic thickness were found in Ra and Rz of 0.07 and 1.00 mm after 14 days of staining. Coca-Cola showed a significant difference in Ra and Rz with 1.00 mm thickness measurement compared to the 0.07 mm group with ≤ of 0.05, which was considered statistically significant. Highest ΔE₀₀ were recorded among samples stained by Coca-Cola, followed by coffee, for both thicknesses. CONCLUSIONS Those findings support previous studies using spectrophotometric analysis of staining of CAD-CAM ceramic veneers that Coca-Cola followed by coffee resulted in the greatest color ΔE₀₀ change.

Biocompatibility and Surface Roughness of Different Sustainable Dental Composite Blocks: Comprehensive In Vitro Study

The study purposed to investigate the biocompatibility and sustainability of two computer-aided design/computer-aided manufacturing (CAD/CAM) resin-based composites compared to a resin-modified ceramic in terms of surface roughness, biofilm formation, cytotoxicity, genotoxicity, and cellular changes observed under transmission electron microscopy (TEM). Three CAD/CAM blocks were used, two resin-based composites [Brilliant Crios (BC) and Cerasmart, (CS) and one hybrid ceramic (Vita Enamic (EN)]. Each block was sectioned into 10 × 12 × 2 mm specimens, followed by finishing and polishing. Each specimen was evaluated for surface roughness using 3D optical profilometry and scanned by scanning electron microscopy. Biofilm formation and its relation to surface roughness have been investigated for all tested materials. A Hep-2 cell line was used to investigate the viability through MTT assay. The cytotoxicity of the materials was measured at 24, 48, and 168 h. The activity of P53, caspase 3, and cytochrome C was evaluated to detect the genotoxicity of different groups, followed by TEM tracking of the cellular changes. Statistical analysis was implemented by utilizing a one-way analysis of variance test. The significance was set at P ≤ 0.05. With regard to the surface roughness, no statistically significant differences were shown between groups. BC possessed the highest biofilm formation value, followed by EN and CS, with no significance between them. No correlation between surface roughness of tested materials and biofilm formation was shown. Considering viability, the highest values were recorded for EN, whereas BC showed the lowest values. P53-fold changes in EN were significantly the lowest, indicating less genotoxicity. Within the current study's limitations, BC showed the highest biofilm formation. However, no significant surface roughness difference or correlation with biofilm formation was observed in tested materials. EN showed the lowest cytotoxicity and the highest viability. EN revealed the best compatibility performance among tested materials. On the contrary, the BC exhibited fewer preferences.

Color stability of hybrid ceramics exposed to beverages in different combinations

Background

The aim of this study is to evaluate the color stability of hybrid ceramics stored in different combinations of beverages that are routinely consumed.

Methods

The specimens were prepared with resin nano-ceramic (Lava Ultimate, 3M Espe, USA) and hybrid ceramic (Vita Enamic, Vita Zahnfabrik, Germany). The specimens were aged in a thermocycler machine for 10,000 cycles. They were stored in different combinations of beverages (water, tea, coke, coffee, red wine, pomegranate juice, and turnip juice) for 12 + 12 h. Surface roughness measurements were performed using a profilometer. The specimen colors were measured using a spectrophotometer. The color values (L-a-b) of the specimens and mean surface roughness values (Ra) were recorded at the end of the 1st (D1), 7th (D7), 14th (D14) and 28th (D28) d.

Results

When the solution groups were examined, significant color changes were observed in the Lava coffee-tea, Enamic coffee-tea, Lava coffee-wine, and Enamic coffee-wine groups compared with the other groups (p < 0.01). Except for the samples in the Lava coffee-wine 28th day (D28) and Enamic coffee-wine 28th day (D28) groups, more color changes were observed in the Lava samples than in the Enamic samples across all groups and periods.

Conclusion

Greater color changes (except for the samples stored in coffee-wine) were observed in the Lava samples than in the Enamic samples across all groups and periods. It was observed that the coffee-tea and coffee-wine beverage combinations produced the greatest color change in hybrid ceramics within the limitations of this study.

Impact of Smokeless Tobacco on the Color Stability of Zirconia, Zirconia-Reinforced Lithium Silicate and Feldspathic CAD/CAM Restorative Materials: An In-Vitro Study

WHO estimates that the global number of tobacco users exceeds 1.3 billion people. Few studies have examined the effect of locally made smokeless tobacco (ST) products on the color changes of material used in dental prosthetics. Bearing the recent advances in CAD/CAM ceramic restorations material in mind, this study aimed to assess ST influence on mean color change (∆E*) values among selected CAD/CAM ceramic types: multilayer zirconia (Ceramill Zolid PS), zirconia-reinforced lithium silicate ceramic (Vita Suprinity), and feldspathic (Vita TriLuxe) restorative materials. The color changes of the ceramics were compared to VITA classical and VITA 3D-MASTER shade guides. Sixty CAD/CAM ceramic specimens (20 samples each) were fabricated from Ceramill Zolid PS, Vita TriLuxe Forte, and VITA Suprinity. Specimens were prepared and divided into two groups according to the ST type and immersed for two weeks. Basic VITA classical and VITA 3D-MASTER colors were recorded at a baseline of one week and two weeks. The highest ∆E* values were recorded in the black ST for Vita Suprinity (4.77) in the first week, followed by Vita TriLuxe (4.07) in the second week. For white ST, Vita TriLuxe (4.87), and Vita Suprinity (4.42) showed extensive color change after two weeks and one week, respectively. The color change was least in zirconia for black and white ST after one week. CAD/CAM ceramic materials showed no significant difference after 1 and 2 weeks for the tested ST types. The effects of ST on CAD/CAM ceramic material (∆E* values) were high but did not reach clinically unacceptable values. Zirconia showed the least amount of color change among all the tested materials.

Comparative Study of the Effectiveness of Laboratory-Formulated Polishing Pastes for Two CAD/CAM Ceramic Restorative Materials

PURPOSE

To evaluate the effect of different polishing pastes with different particle sizes on the surface finish of two different CAD/CAM ceramics.

MATERIALS AND METHODS

A total of 128 specimens were prepared of two CAD/CAM ceramics: lithium disilicate (12.4 × 14.5 × 2 mm) and monolithic zirconia (17.5 × 12.5 × 2.5 mm). They were divided randomly into 8 groups according to surface treatment (n = 8). Group 1 (control) was left as received after crystallization or sintering with no further surface treatment; Group 2 (glazed); Group 3 (positive control), where specimens were polished using standardized surface treatment (medium grit silicon carbide discs, rubber cup and pumice slurry, then rubber cup and toothpaste). For groups 4 to 8, in addition to silicon carbide and pumice slurry polishing, specimens were further polished using a diamond paste (DP), and polishing pastes of microzirconia (MZ), nanosilica (NS), nanodiamond (ND), and nanozirconia (NZ), respectively. Surface roughness (R_a ) was measured using noncontact profilometer. The mean values were compared using ANOVA and Post Hoc Tukey's test (α = 0.05). Specimens' surfaces were studied using a scanning electron microscope (SEM).

RESULTS

Positive control group and MZ exhibited significant R_a of lithium disilicate compared to control (p ˂ 0.001), glazed (p = 0.001), DPs (p = 0.002), NS (p ˂ 0.001), ND (p ˂ 0.001), and NZ (p = 0.002). In the case of zirconia, positive control showed a significantly higher R_a compared to all other groups (p ˂ 0.001). No statistical difference was found between all other polishing techniques (positive control, glazed, DPs, NS, ND, MZ, and NZ) (p > 0.05).

CONCLUSION

Polishing with ND, NZ, and NS lab-formulated pastes produced surfaces with comparable smoothness to control and glazed specimens for lithium disilicate and zirconia ceramic materials.

Assessment of Color Stainability of Computer-Aided Design and Computer-Aided Manufacturing (CAD/CAM) Ceramic Materials After Hot and Cold Coffee Immersion at Different Time Intervals

BACKGROUND This spectrophotometric study assessed the color stability of CAD/CAM restorative materials with different exposed surfaces following staining by hot Arabic Qahwa and cold coffee. MATERIAL AND METHODS Ninety-six specimens were fabricated from 3 different CAD/CAM ceramic materials: Vita Suprinity (Vita-S), Vita Enamic (Vita-E), and Vitablocs Mark II (Vitablocs-MII). We divided 32 specimens for each group into glazed or polished surfaces, with 16 specimens in each group, then subdivided them according to staining materials: Arabic Qahwa and Frappuccino Cold Coffee. Color of specimens was measured during immersion in staining materials (BEFORE) as baseline with (Vita classic) and (L, a, b), for average color changes (ΔE₀₀), then remeasured after 2, 4, and 12 weeks, and described as 1st, 2nd, and 3rd measurements for VITAPAN Classic shade and T1, T2, and T3 for ΔE00 values using the CIE L*a*b* equation. We performed ANOVA and then post hoc testing. RESULTS We found significant differences in ΔE₀₀ values during immersing in hot Arabic Qahwa and cold coffee for tested materials in glazed or polished specimens. Polished specimens of Vita-S and Vita-E had the highest color changing and staining compared to glazed surfaces. Vitablocs-MII had the best color stability through immersion periods. Moreover, there were changes in relation to VITAPAN Classic shade guide for both Vita-S and Vita-E specimens during different immersion periods. CONCLUSIONS Coffee caused staining and contamination of ceramic material. Values of ΔE₀₀ for tested ceramic materials were significantly different but were within the clinically acceptable range. Polished specimens showed higher staining; therefore, we highly recommend re-glazing of ceramic restorations to maintain color stability.

Color Stability and Translucency of Polymer-Infiltrated Ceramic-Network Materials—A Systematic Review of the Literature

This systematic review aimed to compile information and report the color stability and translucency of polymer-infiltrated ceramic-network (PICN) materials for suitable clinical applications in dentistry. Original peer-reviewed articles in electronic databases including PubMed, MEDLINE, Scopus, and Web of Science were searched to identify relevant papers published between January 2013 and August 2020. The published papers were only in the English language and limited to in vitro studies, and experimental reports were considered. The data from nine studies were considered when reviewing the color stability and translucency of PICN in comparison to other commonly used restorative materials. Among the included studies, color stability assessment was performed in five studies, and the other four studies were involved in the combined assessment of both color stability and translucency. PICN materials are a comparatively newer class of restorative materials and are recommended to overcome the drawbacks of ceramics and resin composites. The outcomes of previous laboratory studies still do not provide convincing results regarding the optical properties of PICN materials. However, with existing sources and evidence, PICN materials exhibit less color stability than ceramics do but better color stability compared to that of resin nanoceramics (RNC) and resin composites. The translucency of PICN materials is low compared to that of ceramics, nanoceramics, and resin composites.

Surface roughness and color measurements of glazed or polished hybrid, feldspathic, and Zirconia CAD/CAM restorative materials after hot and cold coffee immersion

Background

The purpose of this study evaluates and compares the effect of surface roughness (Ra) and color stability on computer-aided design/computer-aided manufacturing (CAD/CAM) hybrid resin (Vita Enamic), feldspathic (Vitablocs® Mark II), and lithium disilicate Zirconia (Vita Suprinity) glazed or polished ceramics immersed in hot Arabic Qahwa and cold coffee.

Methods

A total of 96 standardized samples were prepared from CAD/CAM restorative materials. Half of the samples were polished as per the manufacturer’s instructions using a porcelain polishing kit, and the other half were glazed. Samples were distributed and immersed in hot Arabian Qahwa and cold coffee followed by thermocycling. Ra measurements and color changes were conducted before and after immersion. SEM images were captured from each type of glazed or polished ceramic. One-way ANOVA paired Student’s t-test, and Bonferroni test were conducted to detect significant difference between the groups. P > 0.05 was a significant level.

Results

Of all the tested samples, Ra increased without any significant difference; however, mean color changes (ΔE*) showed significant differences. An increase in Ra was noted for all the glazed and polished samples after immersion and thermocycling. However, differences were significant only in VM II. In addition, ΔE* was significant only in Vita Suprinity (VS) samples. For immersion groups, significant Ra changes were noticed in glazed samples, only in Vita Enamic (VE) with no ΔE*. In polished samples, mean Ra changes were observed in VM II and VS samples. Significant differences were also noticed in polished VE and VS subgroups of ΔE*.

Conclusions

Ra affects all the tested samples, providing higher values on the polished specimens. The ΔE* caused by hot Arabic Qahwa and cold coffee on glazed or polished CAD/CAM restorative materials were clinically acceptable.

Effects of Khat on Surface Roughness and Color of Feldspathic and Zirconia Porcelain Materials under Simulated Oral Cavity Conditions

Background and Objectives: Khat chewing is considered as a daily habit that is practiced by more than five million people globally. The effect of khat chewing on the surface roughness and the color stability of natural teeth and the material used in the fabrication of dental prosthesis remains unknown. This study was conducted to explore and compare the effect of khat homogenate (KH) on the surface roughness (Ra) and the average color changes (ΔE*) amongst natural teeth and selected shades from different porcelain types, namely, feldspathic metal ceramic (MC) VM13, computer-aided design/computer assisted manufacture (CAD/CAM) feldspathic (Vitablocs Mark II), and multilayer zirconia (Ceramill Zolid PS) porcelains. Materials and Methods: Seventy samples were prepared from natural teeth, feldspathic MC, CAD/CAM Vitablocs Mark II, and zirconia porcelain. The Ra values were measured using a profilometer and expressed in micrometers, whereas the ΔE* values were measured using VITA Easyshade® V spectrophotometer for all samples before and after frequent immersion and thermocycling in KH for 30 days. The surface topography was used to assess the materials surfaces (glazed or polished) after KH immersion by using a white light interferometry machine. Results: Results revealed that the Ra and the ΔE* values of the different types of tested porcelain were influenced by KH. The order of surface roughness values was glazed or polished MC > polished Zircon > polished Vitablocs Mark II > natural teeth. The lowest ΔE* values were recorded for glazed Vitablocs Mark II and MC, and the values could be arranged as polished zircon > natural teeth > glazed zircon > polished MC > polished Vitablocs Mark II. P values were significantly varied (< 0.001) among all the tested groups, except the zircon group (>0.05) for both Ra and ΔE*. Conclusion: KH significantly affected both surface parameter and color of glazed or polished porcelain materials and natural teeth.