Fabrication of blend polyvinylidene fluoride/chitosan membranes for enhanced flux and fouling resistance

Preparation of a novel DNA-imprinted sensor based on chitosan and its highly sensitive detection of Pb2

Lead ion is very harmful to the environment, so it is very important to study its detection methods. In this study, a novel electrochemical sensor was constructed by modifying deoxyribonucleic acid (DNA) on the electrode, which can be used for the detection of Pb2+ in the environment. Part of the mixed solution of chitosan (CS) and Pb2+ template ions was dropped onto the surface of a glassy carbon electrode. CS-Pb2+ film was cross-linked through sodium tripolyphosphate. And a novel DNA-imprinted sensor was prepared by electrodepositing CS-Pb2+ thin film with gold nanoparticles (AuNPs), removing Pb2+ templates, and immobilizing specific double-stranded DNA. The electroactive area, surface morphology, sensitivity, and electrochemical reaction mechanism of the DNA-imprinted sensor were analyzed. The elementary reaction steps were studied through electrochemical reaction kinetics analysis. The experimental results indicate that the DNA-imprinted electrochemical biosensor can quantitatively detect Pb2+ in the range of 10-100 μM (R2 = 0.9935), and its detection limit is 6.5074 μM (3σ/slope). The sensitivity of the electrochemical biosensor is 1.55233 × 10-6 A/μM, and its active areas is 6.233 cm2. The desorption mechanism and adsorption mechanism have been explored through dynamic parameter analysis. The novel DNA imprinted electrochemical biosensor developed in this paper provides a robust method for detecting lead ions in solution. Additionally, it establishes a solid groundwork for detecting other metal ions.

High-performance sulfonated polyether sulfone/chitosan membrane on creatinine transport improved by lithium chloride

Membrane-based polyether sulfone (PES) is a potential candidate for hemodialysis because of its properties such as high mechanical strength, thermal stability, and chemical resistance. However, the nature of the hydrophobicity in the PES membrane inhibits their performance in transporting creatinine. In this study, polyethersulfone (PES) membranes were modified using a sulfonation process and the addition of chitosan (CS) and lithium chloride (LiCl) to improve its performance in transporting creatinine. The FTIR spectrum of the modified membrane shows peaks of the sulfonate (-SO2), amine (NH), and hydroxyl (-OH) groups in absorption areas of 1065 cm-1, 1650 cm-1, and 3384 cm-1, respectively, indicating that the membrane SPES/CS-LiCl has been successfully prepared. The modified PES membranes shows a higher porosity, swelling, water absorption, and hydrophilicity than pure PES membrane. The modification of the PES membrane in this study also enhances the ability of the membrane to transport creatinine. In the pure PES membrane, the creatinine clearance is 0.30 mg/dL, while in the SPES/CS-LiCl (5:2) membrane the creatinine clearance is 0.42 mg/dL.

Effect of chitosan crosslinking time on the structure and antifouling performance of polyvinylidene fluoride membrane by surface gelation-immersion precipitation phase inversion

Polyvinylidene fluoride (PVDF) porous membrane was prepared by a two-step method of surface gelation-immersion precipitation phase inversion. Chitosan/acetic acid solution and glutaraldehyde aqueous solution were sequentially sprayed onto the surface of the PVDF solution film, with chitosan crosslinking and gelation occurring simultaneously on the film surface. The solution film was then immersed in a coagulation bath to obtain a modified PVDF porous membrane. The effect of the crosslinking time of chitosan and glutaraldehyde on the structure and properties of the PVDF porous membrane was discussed. The results showed that with the prolongation of crosslinking time, the surface structure of the membrane changed from a dense skin layer to a porous structure; the porosity and the mean pore size of the modified PVDF membranes increased first and then decreased, and the contact angle gradually decreased. When the crosslinking time extended to 15 min, the water flux of modified membrane (M153) reached a maximum value. BSA dynamic cyclic filtration experiment showed that the retention rate (R) of the modified membrane was significantly improved, compared to 68.3% retention rate of the blank membrane (M000), but the crosslinking time had little effect on the retention rates of the four modified membranes. The antifouling data showed that the flux recovery rate of the blank membrane was 73.0%, while the flux recovery rate of the modified membrane can reach as high as 84.40%, and the irreversible pollution rate of the blank membrane was 27.7%, while the irreversible pollution rate of the modified membrane reduced to 15.6%. These results indicated that, after surface chitosan crosslinking, the hydrophilicity and antifouling properties of PVDF membranes were improved. PRACTITIONER POINTS: Modified PVDF membranes with crosslinking CS coating were prepared by a two-step method of surface gelation-immersion precipitation phase inversion. -OH groups and -NH2 groups of CS coating improve the hydrophilicity and the antifouling property of modified PVDF membranes. Modified PVDF membranes had larger mean pore size and higher porosity than unmodified membrane. Flux recovery rates of the modified membranes were higher than that of unmodified membrane. Pollution degree, reversible pollution rate, and irreversible pollution rate of modified membranes were lower than those of unmodified membrane.

Construction of a multi-layer protection of CS polymer brush grafted DA@CNTs coating on PVDF membrane for effective removal of dye effluent

In the process of removing dye wastewater, the membrane surface is susceptible to contamination, resulting in reduced performance and limited dye separation efficiency. A single hydrophilic modification layer is not enough to achieve effective separation of different types of dyes. The present research designed a "double layer protection" method in order to overcome the above deficiencies. A solution of dopamine (DA) coated carbon nanotubes (CNTs-COOH) was covered on the surface of the polyvinylidene fluoride (PVDF) membrane by deposition, followed by grafting a layer of chitosan (CS) polymer brushes on its surface. The spatial double layer structure provides an excellent barrier effect and effectively reduces the contamination of dyes. When filtering different types of dyes, effective filtration of anionic and cationic dyes through the electrostatic effect of the first layer, the adsorption of CNTs in the second layer and the hydration layer of both layers. All membranes have excellent rejection properties. More importantly, the membranes also had good chemical and mechanical stability and their serviceability was not degraded. Therefore, the prepared PVDF-based multi-layer composite membranes behave a potential application prospect in the wastewater purification field.

In-situ photoreduction strategy for synthesis of silver nanoparticle-loaded PVDF ultrafiltration membrane with high antibacterial performance and stability

Ultrafiltration (UF) technology using polyvinylidene fluoride (PVDF) membrane has been widely applied to water and wastewater treatment due to its low cost and simple operation process. However, PVDF-based UF membrane always encountered the issue of membrane biofouling that greatly impacted the filtration performance. In this study, we prepare a silver nanoparticle (AgNP)-loaded PVDF (Ag/PVDF) UF membrane by an in-situ photoreduction method to mitigate the membrane biofouling. Different from the previously reported method, AgNPs were synthesized in-situ by a UV photoreduction process, in which Ag⁺ ions were reduced to zero-valent Ag nanoparticles by the photo-induced reducing radicals. Antibacterial experiments showed that the inhibition efficiency of Ag/PVDF membrane to Escherichia coli reached up to ~ 99% after antibacterial treatment for 24 h. In comparison with the pristine PVDF membrane, Ag/PVDF membrane possessed a lower water contact angle (83.7° vs. 38.1°), and its pure water flux increased by 23.7%, and a high bovine serum albumin (BSA) rejection efficiency was maintained. In addition, the high stability of the Ag/PVDF composite membrane was confirmed by the extremely low releasing amount of Ag. This study provides a novel strategy for the preparation of metal nanoparticle-incorporated Ag/PVDF ultrafiltration composite membrane showing favorable antibacterial performance and stability.

Surface Engineering of a Bioartificial Membrane for Its Application in Bioengineering Devices

Membrane technology is playing a crucial role in cutting-edge innovations in the biomedical field. One such innovation is the surface engineering of a membrane for enhanced longevity, efficient separation, and better throughput. Hence, surface engineering is widely used while developing membranes for its use in bioartificial organ development, separation processes, extracorporeal devices, etc. Chemical-based surface modifications are usually performed by functional group/biomolecule grafting, surface moiety modification, and altercation of hydrophilic and hydrophobic properties. Further, creation of micro/nanogrooves, pillars, channel networks, and other topologies is achieved to modify physio-mechanical processes. These surface modifications facilitate improved cellular attachment, directional migration, and communication among the neighboring cells and enhanced diffusional transport of nutrients, gases, and waste across the membrane. These modifications, apart from improving functional efficiency, also help in overcoming fouling issues, biofilm formation, and infection incidences. Multiple strategies are adopted, like lysozyme enzymatic action, topographical modifications, nanomaterial coating, and antibiotic/antibacterial agent doping in the membrane to counter the challenges of biofilm formation, fouling challenges, and microbial invasion. Therefore, in the current review, we have comprehensibly discussed different types of membranes, their fabrication and surface modifications, antifouling/antibacterial strategies, and their applications in bioengineering. Thus, this review would benefit bioengineers and membrane scientists who aim to improve membranes for applications in tissue engineering, bioseparation, extra corporeal membrane devices, wound healing, and others.

Synergistic Effect of Chitosan and Metal Oxide Additives on Improving the Organic and Biofouling Resistance of Polyethersulfone Ultrafiltration Membranes

The combination of chitosan and metal oxides was utilized as an addition to improve the fouling resistance of polyethersulfone (PES) ultrafiltration membranes. Pure water flux, membrane hydrophilicity by the contact angle, scanning electron micrographs, and Fourier-transform infrared spectra were used to characterize the membranes. With the addition of metal oxides, the modified membrane's water flux increased. The PES membrane with 0.25% wt chitosan and 2.0% wt AgNO₃ had the highest flux and antibacterial activity among the membranes tested. Because of its potential to improve membrane hydrophilicity, the water flux increased with the addition of chitosan and AgNO₃. Because of the improved hydrophilicity, the contact angle reduced as chitosan and Ag loading was increased. The PES-chitosan-Ag₂O (from AgNO₃ 2.0% wt) membrane had high antibacterial activity against Escherichia coli and Staphylococcus aureus, whereas the PES-2.0% wt Ag membrane did not show the same result. Finally, the addition of chitosan in the PES-Ag membrane increased the membrane's antibacterial activity substantially.

Development of green polylactic acid asymmetric ultrafiltration membranes for nutrient removal

Polylactides are a prominent class of biocompatible and biodegradable polymers that can be used to fabricate membranes for wastewater treatment. Excessive nutrient (phosphorus and nitrogen) concentrations in water bodies are a serious concern that has resulted in widespread health problems and potable water shortages. In this study, ultrafiltration (UF) membranes were prepared from polylactic acid (PLA) using the phase inversion method. Scanning electron microscope (SEM), thermogravimetric analyzer (TGA), and Fourier-transform infrared (FTIR) analysis were used to characterize the membranes. The hydrophilicity of the membrane surface was investigated by analyzing the water contact angle (CA). The results showed that the PLA membranes had a finger-like asymmetric morphology and various dense pore sizes. When the concentration of the PLA polymer increased from 15% to 20%, the removal of ammonium‑nitrogen (NH₄⁺-N) increased from 41.9 ± 1.3% to 95.9 ± 3.1% and from 50% to 87% for synthetic and raw wastewater samples, respectively. Up to 52% removal rates of phosphates (PO₄^3--P) were achieved using PLA membranes. This study revealed a great opportunity to develop green, efficient, and sustainable PLA membranes for the treatment of wastewater with high nutrient content.

Cold atmospheric plasma modification and electrical conductivity induction in gelatin/polyvinylidene fluoride nanofibers for neural tissue engineering

BACKGROUND

This research follows some investigations through neural tissue engineering, including fabrication, surface treatment, and evaluation of novel self-stimuli conductive biocompatible and degradable nanocomposite scaffolds.

METHODS

Gelatin as a biobased material and polyvinylidene fluoride (PVDF) as a mechanical, electrical, and piezoelectric improvement agent were co-electrospun. In addition, polyaniline/graphene (PAG) nanoparticles were synthesized and added to gelatin solutions in different percentages to induce electrical conductivity. After obtaining optimum PAG percentage, cold atmospheric plasma (CAP) treatment was applied over the best samples by different plasma variable parameters. Finally, the biocompatibility of the scaffolds was analyzed and approved by in vitro tests using two different PC12 and C6 cell lines. In the present study the morphology, FTIR, dynamic light scattering, mechanical properties, wettability, contact angle tests, differential scanning calorimetric, rate of degradation, conductivity, biocompatibility, gene expression, DAPI staining, and cell proliferation were investigated.

RESULTS

The PAG percentage optimization results revealed fiber diameter reduction, conductivity enhancement, young's modulus improvement, hydrophilicity devaluation, water uptake decrement, and degradability reduction in electrospun nanofibers by increasing the PAG concentration. Furthermore, ATR-FTIR, FE-SEM, AFM, and contact angle tests revealed that helium CAP treatment improves scaffold characterizations for 90 seconds in duration time. Furthermore, the results of the MTT assay, FE-SEM, DAPI staining, and RT-PCR revealed that samples containing 2.5% w/w of PAG are the most biocompatible, and CAP treatment increases cell proliferation and improves neural gene expression in the differentiation medium.

CONCLUSIONS

According to the results, the samples with the 2.5% w/w of PAG could provide a suitable matrix for neural tissue engineering in terms of physicochemical and biological.

Decreasing free fatty acid of crude palm oil with polyvinylidene fluoride hollow fiber membranes using a combination of chitosan and glutaraldehyde

Crude palm oil (CPO) has emerged as a significant commodity in the economic and social development of producer nations.

Novel Molecular Organic Framework Composite Molecularly Imprinted Nanofibrous Membranes with a Bioinspired Viscid Bead Structure for Selective Recognition and Separation of Atrazine

In this work, novel atrazine (ATZ) molecularly imprinted nanofibrous membranes (A-MNMs) with a molecular organic framework (MOF)-based viscid bead structure were developed based on a natural spider-web-inspired strategy for selective separation of ATZ. Poly(vinylidene fluoride)/poly(vinyl alcohol) (PVDF/PVA) blended nanofibrous membranes as the basal membrane were synthesized by electrospinning technology combined with a chemical cross-linking procedure. The most critical design is that MOF nanocrystals as the matrix of the viscid bead structure were assembled on the PVDF/PVA blended nanofibrous membrane surface and the specific recognition sites were efficiently constructed on the surface and pores of the MOF-based viscid bead structure by a surface imprinting strategy. Significantly, the as-synthesized MOF-based viscid bead structure has an enhanced specific surface area, which helps to form abundant specific recognition sites in A-MNMs. Therefore, the A-MNMs with a spider-web-like structure presented an enhanced rebinding capacity (37.62 mg g^-1) and permselectivity (permselectivity factors β were 4.21 and 4.31) toward ATZ. Moreover, the A-MNMs display strong practicability in separation of ATZ from simulated environmental water samples. The presented work has shown tremendous potential for preparing natural spider-web-like molecularly imprinted membranes (MIMs) for selective separation of environment pollutants.

Increased E. coli bio-adsorption resistance of microfiltration membranes, using a bio-inspired approach

Cells have inherent anti-fouling properties. The mechanisms underpinning these natural properties inform the design of an anti-biosorption coating for a polyethersulfone microfiltration membrane, which includes polydopamine and chitosan layers. This tri-layered membrane is created using quick and easy synthesis method. Its ability to resist bio-adsorption and membrane extracellular polymeric substances (EPS) formation is investigated using the bacterium E. coli (ATCC 11775, 1.5 × 10⁷ CFU/mL). In addition, the proliferative bio-adsorption process is explored on the microfiltration membrane surface, using natural water under static and shaken conditions, while monitoring the bio-adsorption kinetics and EPS dynamic changes. The characterization results show that the modification by polydopamine and chitosan change the membrane surface morphology and increase its hydrophilicity. After 10 min dipping in 5 g/L chitosan solution, the pure water flux of the modified membrane is 5469 ± 30 L/(m²·h) (0.2 bar) and the contact angle decreases to 36.7 ± 1.0°, compared with 9889 ± 23 L/(m²·h) (0.2 bar) and 60.3 ± 1.5° for the unmodified polyethersulfone membrane, respectively. In proliferative bio-adsorption tests, the modified membrane is shown to decrease bio-adsorption by 0.4-2.3 orders of magnitude. However, no antimicrobial function is observed, probably due to the alkaline environment and insufficient functional amino groups. A series of linear and non-linear kinetic models is applied to fit the proliferative bio-adsorption process. The pseudo-second-order model is found to describe the proliferative bio-adsorption process best. Neither total organic carbon (TOC) nor protein is detected on the modified membrane surface. In contrast, on the unmodified PES membrane the ratios of protein/TOC (%), TOC/abundance ((μg/cm²)/CFU (log)) and protein/abundance ((μg/cm²)/CFU(log)) are 10%-16%, 0.17-0.28 and 0.02-0.04, respectively. No significant difference (p > 0.05) is found between static and shaken conditions. All these results point to improved anti-biosorption properties for water treatment applications, encouraging further studies on this membrane.

Effect of hydrophilic silica and dual coagulation bath on structural and mechanical properties of PVDF membrane for membrane distillation

The water scarcity threatens environmental health and human development. Membrane distillation (MD) is one of the most applicable processes for purifying water using a hydrophobic membrane. In this study, the synergetic effect of SiO₂ nanoparticles as well as employing the dual coagulation bath on physical and mechanical properties of Polyvinylidene Fluoride (PVDF) flat-sheet membranes produced by dry-wet phase inversion (DIPS) technique has been investigated. The results of microstructural analysis using Scanning Electron Microscope (SEM) demonstrated that by adding nanoparticles while the pore size decreased noticeably, the percentage of porosity significantly increased. Also, it has been revealed that by utilizing isopropanol as the first coagulation bath the finger-like macro-voids became smaller in size, and the share of sponge-like structures rose remarkably. The membrane performance was tested by Vacuum Membrane Distillation (VMD) for measuring the flux and Liquid Entry Pressure (LEP_w) laboratory setup. It can be seen that by increasing the content of SiO₂ nanoparticles to 6 wt.% while the LEP_w approximately halved, the flux soared to about 10000 g/m²h. Moreover, mechanical testing showed that although the tensile strength of nanocomposite samples fabricated in isopropanol dual coagulation bath was improved by up to 66%, their ductility slightly declined. Furthermore, the hydrophobicity of each membrane was examined via contact angle measurements. Finally, it was found that all membranes completely rejected the NaCl in rejection test. Graphical abstract.

The Recent Progress in Modification of Polymeric Membranes Using Organic Macromolecules for Water Treatment

For decades, the water deficit has been a severe global issue. A reliable supply of water is needed to ensure sustainable economic development in population growth, industrialization and urbanization. To solve this major challenge, membrane-based water treatment technology has attracted a great deal of attention to produce clean drinking water from groundwater, seawater and brackish water. The emergence of nanotechnology in membrane science has opened new frontiers in the development of advanced polymeric membranes to enhance filtration performance. Nevertheless, some obstacles such as fouling and trade-off of membrane selectivity and permeability of water have hindered the development of traditional polymeric membranes for real applications. To overcome these issues, the modification of membranes has been pursued. The use of macromolecules for membrane modification has attracted wide interests in recent years owing to their interesting chemical and structural properties. Membranes modified with macromolecules have exhibited improved anti-fouling properties due to the alteration of their physiochemical properties in terms of the membrane morphology, porosity, surface charge, wettability, and durability. This review provides a comprehensive review of the progress made in the development of macromolecule modified polymeric membranes. The role of macromolecules in polymeric membranes and the advancement of these membrane materials for water solution are presented. The challenges and future directions for this subject are highlighted.

Novel Composite Membranes Based on Chitosan Copolymers with Polyacrylonitrile and Polystyrene: Physicochemical Properties and Application for Pervaporation Dehydration of Tetrahydrofuran

Pervaporation has been applied for tetrahydrofuran (THF) dehydration with novel composite membranes advanced by a thin selective layer composed of chitosan (CS) modified by copolymerization with vinyl monomers, acrylonitrile (AN) and styrene, in order to improve the chemical and mechanical stability of CS-based membranes. Composite membranes were developed by depositing a thin selective layer composed of CS copolymers onto a commercially-available porous support based on aromatic polysulfonamide (UPM-20^®). The topography and morphology of the obtained materials were studied by atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction analysis (XRD). Thermal properties and stability were determined by coupled evolved gas analysis (EGA-MS). Transport properties were estimated in pervaporation dehydration of THF. The effect of operating parameters for the pervaporation dehydration of THF such as feed compositions and temperatures (295, 308 and 323 K) was evaluated. It was shown that CS modification with different vinyl monomers led to a difference in physical and transport properties. The composite membrane with the thin selective layer based on CS-PAN copolymer demonstrated optimal transport properties and exhibited the highest water content in the permeate with a reasonably high permeation flux.