Efficient preparation of a novel PVDF antifouling membrane based on the solvent-responsive cleaning properties

Reactive layered hydroxide membrane for advanced water treatment: Micropollutant degradation and antifouling potential

The effective removal of micropollutants by water treatment technologies remains a significant challenge. Herein, we develop a CoFe layered double hydroxide (CoFeLDH) catalytic membrane for peroxymonosulfate (PMS) activation to achieve efficient micropollutant removal with improved mass transfer rate and reaction kinetics. This study found that the CoFeLDH membrane/PMS system achieved an impressive above 98% degradation of the probe chemical ranitidine at 0.1 mM of PMS including five more micropollutants (Sulfamethoxazole, Ciprofloxacin, Carbamazepine, Acetaminophen and Bisphenol A) at satisfactory level (above 80%). Moreover, significant improvements in water flux and antifouling properties were observed, marking the membrane as a specific advancement in the removal of membrane fouling in water purification technology. The membrane demonstrated consistent degradation efficiency for several micropollutants and across a range of pH (4-9) as well as different anionic environments, thereby showing it suitability for scale-up application. The key role of reactive species such as SO4•-, and O2• - radicals in the degradation process was elucidated. This is followed by the confirmation of the occurrence of redox cycling between Co and Fe, and the presence of CoOH+ that promotes PMS activation. Over the ten cycles, the membrane could be operated with a flux recovery of up to 99.8% and maintained efficient performance over 24 h continuous operation. Finally, the efficiency in degrading micropollutants, coupled with reduced metal leaching, makes the CoFeLDH membrane as a promising technology for application in water treatment.

Advances in 2D Materials Based Gas Sensors for Industrial Machine Olfactory Applications

The escalating development and improvement of gas sensing ability in industrial equipment, or "machine olfactory", propels the evolution of gas sensors toward enhanced sensitivity, selectivity, stability, power efficiency, cost-effectiveness, and longevity. Two-dimensional (2D) materials, distinguished by their atomic-thin profile, expansive specific surface area, remarkable mechanical strength, and surface tunability, hold significant potential for addressing the intricate challenges in gas sensing. However, a comprehensive review of 2D materials-based gas sensors for specific industrial applications is absent. This review delves into the recent advances in this field and highlights the potential applications in industrial machine olfaction. The main content encompasses industrial scenario characteristics, fundamental classification, enhancement methods, underlying mechanisms, and diverse gas sensing applications. Additionally, the challenges associated with transitioning 2D material gas sensors from laboratory development to industrialization and commercialization are addressed, and future-looking viewpoints on the evolution of next-generation intelligent gas sensory systems in the industrial sector are prospected.

Effect of chitosan crosslinking time on the structure and antifouling performance of polyvinylidene fluoride membrane by surface gelation-immersion precipitation phase inversion

Polyvinylidene fluoride (PVDF) porous membrane was prepared by a two-step method of surface gelation-immersion precipitation phase inversion. Chitosan/acetic acid solution and glutaraldehyde aqueous solution were sequentially sprayed onto the surface of the PVDF solution film, with chitosan crosslinking and gelation occurring simultaneously on the film surface. The solution film was then immersed in a coagulation bath to obtain a modified PVDF porous membrane. The effect of the crosslinking time of chitosan and glutaraldehyde on the structure and properties of the PVDF porous membrane was discussed. The results showed that with the prolongation of crosslinking time, the surface structure of the membrane changed from a dense skin layer to a porous structure; the porosity and the mean pore size of the modified PVDF membranes increased first and then decreased, and the contact angle gradually decreased. When the crosslinking time extended to 15 min, the water flux of modified membrane (M153) reached a maximum value. BSA dynamic cyclic filtration experiment showed that the retention rate (R) of the modified membrane was significantly improved, compared to 68.3% retention rate of the blank membrane (M000), but the crosslinking time had little effect on the retention rates of the four modified membranes. The antifouling data showed that the flux recovery rate of the blank membrane was 73.0%, while the flux recovery rate of the modified membrane can reach as high as 84.40%, and the irreversible pollution rate of the blank membrane was 27.7%, while the irreversible pollution rate of the modified membrane reduced to 15.6%. These results indicated that, after surface chitosan crosslinking, the hydrophilicity and antifouling properties of PVDF membranes were improved. PRACTITIONER POINTS: Modified PVDF membranes with crosslinking CS coating were prepared by a two-step method of surface gelation-immersion precipitation phase inversion. -OH groups and -NH2 groups of CS coating improve the hydrophilicity and the antifouling property of modified PVDF membranes. Modified PVDF membranes had larger mean pore size and higher porosity than unmodified membrane. Flux recovery rates of the modified membranes were higher than that of unmodified membrane. Pollution degree, reversible pollution rate, and irreversible pollution rate of modified membranes were lower than those of unmodified membrane.

Effect of spraying polyvinyl alcohol solution on the surface of liquid film on the structure and antifouling properties of polyvinylidene membrane

Polyvinylidene fluoride (PVDF) membrane was prepared by a two-step method of surface gelation-immersion precipitation. The surface of the scraping solution film was sprayed with polyvinyl alcohol (PVA) aqueous solution to gel the film surface first, and then the liquid film was immersed in a coagulation bath for phase transformation to obtain the surface modified PVDF membrane. The effects of PVA solution with different mass fraction on the structure and properties of PVDF membrane were studied. The results showed that with the increase of spraying PVA mass fraction, the contact angle of the upper surface of PVDF membranes gradually decreased, the porosity and mean pore size of PVDF membranes gradually increased, and the crystallinity of PVDF membranes gradually decreased. The pores on upper surface of the membranes first increased and then decreased, and the finger-like macropore structure appeared inside the membranes, the water flux first increased and then decreased, and the rejection rate increased. Dynamic cycle filtration experiment of bovine serum protein (BSA) solution showed an increase in membrane flux recovery from 68.31 to 95.08% and a decrease in the irreversible fouling rate from 31.69 to 4.92%, indicating an improvement in the hydrophilicity and antifouling properties of the modified PVDF membrane.

Antifouling enhancement of polyacrylonitrile-based membrane grafted with poly(sulfobetaine methacrylate) layers

In this work, zwitterionic polyacrylonitrile (PAN)-based membranes were synthesized via surface grafting strategy for improving the antifouling properties. The copolymer membrane consisting of PAN and poly(hydroxyethyl methacrylate) segments, was cast via nonsolvent induced phase separation, and then treated with acryloyl chloride to tether with carbon-carbon double bonds. Zwitterionic poly(sulfobetaine methacrylate) (PSBMA) layers were grafted onto membrane surface via concerted reactions of radical grafting copolymerization and quaternization with 2-(dimethylamino)ethyl methacrylate) and 1, 3-propanesultone (1, 3-PS) as the monomers. The grafting degree (GD) of PSBMA layers increases with the incremental content of monomers, leading to the enhancement in membranes surface hydrophilicity. The permeation experiments show that the flux of the zwitterionic membrane increases and then decreases with the increasing GD value, because of the surface coverage of PSBMA layers. The zwitterionic membrane has excellent separation efficiency for oil-in-water emulsion, with the rejection of a higher value than 99%. The irreversible membrane fouling caused by oil adsorption has been suppressed, as proved by the cycle-filtration tests. These outcomes confirm that oil-fouling resistances of membranes are improved obviously by the surface grafting of zwitterionic PSBMA layers.

Design of Switchable Enzyme Carriers Based on Stimuli-Responsive Porous Polymer Membranes for Bioapplications

Design of efficient enzyme carriers, where enzymes are conjugated to supports, has become an attractive research avenue. Immobilized enzymes are advantageous for practical applications because of their convenience in handling, ease of separation, and good reusability. However, the main challenge is that these traditional enzyme carriers are unable to regulate the enzymolysis efficiency or to protect the enzymes from proteolytic degradation, which restricts their effectiveness of enzymes in bioapplications. Enlightened by the stimuli-responsive channels in the natural cell membranes, conjugation of the enzymes within flat-sheet stimuli-responsive porous polymer membranes (SR-PPMs) as artificial cell membranes is an efficient strategy for circumventing this challenge. Controlled by the external stimuli, the multifunctional polymer chains, which are incorporated within the membranes and attached to the enzyme, change their structures to defend the enzyme from the external environmental disturbances and degradation by proteinases. Specifically, smart SR-PPM enzyme carriers (SR-PPMECs) not only permit convective substrate transfer through the accessible porous network, dramatically improving enzymolysis efficiency due to the adjustable pore sizes and the confinement effect, but they also act as molecular switches for regulating its permeability and selectivity. In this review, the concept of SR-PPMECs is presented. It covers the latest developments in design strategies of flat-sheet SR-PPFMs, fabrication protocols of SR-PPFMECs, strategies for the regulation of enzymolysis efficiency, and their cutting-edge bioapplications.

Studies on the electrostatic effects of stretched PVDF films and nanofibers

The electroactive β-phase in Poly (vinylidene fluoride, PVDF) is the most desirable conformation due to its highest pyro- and piezoelectric properties, which make it feasible to be used as flexible sensors, wearable electronics, and energy harvesters etc. In this study, we successfully developed a method to obtain high-content β-phase PVDF films and nanofiber meshes by mechanical stretching and electric spinning. The phase transition process and pyro- and piezoelectric effects of stretched films and nanofiber meshes were characterized by monitoring the polarized light microscopy (PLM) images, outputting currents and open-circuit voltages respectively, which were proved to be closely related to stretching ratio (λ) and concentrations. This study could expand a new route for the easy fabrication and wide application of PVDF films or fibers in wearable electronics, sensors, and energy harvesting devices.

Comb-like structural modification stabilizes polyvinylidene fluoride membranes to realize thermal-regulated sustainable transportation efficiency

Hydrophobic micro-porous membrane such as polyvinylidene fluoride (PVDF) with excellent thermal-/chemical-stability and low surface energy has received extensive attention in industrial water treatment and sustainable energy conversion. However, undesirable contaminants caused by inevitable proteins or microorganisms adhesion may lead to a rapid loss of separation efficiency, which significantly deteriorate their porous structures and eventually limit their practical performance. Herein, we present a scalable approach for fabricating comb-like copolymer modified PVDF membranes (PVDF-PN@AgNPs) that prevent bacteria from proliferating on the surface and temperature-controlled release of adhered contaminants. Comb-like structured copolymers were imparted to a polydopamine (PDA)-treated PVDF membrane by Michael addition reaction, which enabled a covalent binding of comb-like structured copolymers to the membrane. Such unique structural design of grafted copolymer, containing hydrophilic side chain and temperature-responsive chain backbone, stably prevents bacteria adhesion and provides reversible surface wettability. Therefore, the resultant membranes were evaluated to prevent bacterial adhesion, high touch-killing efficiency and temperature-controlled contaminants release (~99% of protein and ~75% of bacteria). Moreover, with the collapse and stretch of grafted copolymer chain backbone, the synthetic membrane further reversibly adjusted inner micro-porous structure and surface wettability, which eventually helped to achieve variable water fluid transport efficiency. This study not only provides a feasible structural design for stably coping with the challenging of antifouling and subsequent contamination adhesion of PVDF membrane, but also potentially answers the significant gap between lab research advances and practical application, particularly in the industrial membrane field.

Electric Assisted Salt-Responsive Bacterial Killing and Release of Polyzwitterionic Brushes in Low-Concentration Salt Solution

Polyzwitterionic brushes with strong antipolyelectrolyte effects have shown great potential as versatile platforms for the development of switchable friction/lubrication and bacterial absorption/desorption surfaces. However, the surface property switches of these brushes are usually triggered by high salt concentrations (>0.53 M), thereby greatly limiting their applications in biological fields where the salt concentration for mammals is ?0.15 M. To solve this problem, an electric field was used to assist the salt-responsive process of the polyzwitterionic brushes to achieve bacterial release at low concentrations of the salt solution. Briefly, poly(3-(dimethyl (4-vinylbenzyl) ammonium) propyl sulfonate) (polyDVBAPS) brushes grafted on ITO surfaces were prepared by surface initiated atom transfer radical polymerization. The bacterial release of this surface was conducted under an electric field, where anions were migrated and enriched around the brush-grafted ITO surface as anode. The local high concentration ion led to the conformation change of the brush and release of the attached bacteria. The effect of salt type, salt concentration, electric field strength, and conducting time on the bacterial release properties were investigated. The results indicated that under an electrical field of 3 V/mm, polyDVBAPS showed release capacities of ?93% for E. coli and ?81% for S. aureus in 0.12 M NaCl electrolyte solution. Furthermore, by the introduction of a bactericidal agent, i.e., Triclosan (TCS), an antibacterial surface with dual functions of killing and release was fabricated. This surface could kill ?90% and release 95% of attached E. coli in a 0.12 M NaCl solution by the application of a 3 V/mm electric field. This work demonstrated the feasibility of triggering a salt-responsive behavior of polyzwitterionic at low salt concentration by assistance of electric field, which would greatly extend the applications of polyzwitterionic, in particular in biological applications.

Co-Deposition of Stimuli-Responsive Microgels with Foulants During Ultrafiltration as a Fouling Removal Strategy

In this study, we show that codeposition of temperature responsive microgels in the foulant cake layer and cleaning of the cake upon stimuli-induced size change of the microgels is an effective method of fouling removal. Humic acid in CaCl₂ solution was used as a model foulant and poly( n-isopropylacrylamide) (p(NIPAm)) and poly( n-isopropylacrylamide- co-sulfobetainemethacrylate) (p(NIPAm- co-SBMA)) were used as temperature responsive microgels. Filtrations were done below the lower critical solution temperature (LCST) and temperature was increased to above the LCST for cleaning. As an extra cleaning a temperature swing of above, below and then again above the LCST was applied. P(NIPAm) was found to be ineffective in cleaning the foulant deposit despite the 20-fold change in its volume with temperature change at LCST. P(NIPAm- co-SBMA) microgels, on the other hand, provided high fouling reversibility on hydrophilic poly(ether sulfone)(PES)/poly(vinylpyrrolidone) (PVP) and hydrophobic PES membranes. Better fouling reversibility with these microgels was observed at low and high solution ionic strength. While the use of microgels alone increased fouling reversibility to some extent, even in the absence of temperature stimulus, 100% reversibility could only be obtained when a temperature switch was applied in the presence of microgels, showing the effect of microgels' volume change in cleaning.