A new approach for characterization of hydrophobization mechanisms of surfactants on muscovite surface

Physico-chemical and electrostatic surface characterisation of mica mineral and its applicability on the adsorption of Safranin Orange and Reactive Black 5 dyes

ABSTRACTThe combined approach of specific surface area (SSA), porosity, microprobe analysis (EMPA), transmission electron microscopy (TEM), scanning electron microscopy (SEM) equipped with EDX and infrared spectroscopy (FTIR) provided the mica mineral physico-chemical and morphological characterisation. The electrostatic surface properties were assessed through the determination of the Point of Zero Charge (pH_PZC) by the drift method and the electrokinetic mica mineral features represented by the Isoelectric Point (pH_IEP) which was carried out through zeta potential measurements. Adsorption tests were performed to correlate the surface charge behaviour of the mica mineral and its influence on the adsorption efficiency of two different dyes, namely: Safranin Orange (SO), as a cationic dye and Reactive Black 5 (RB5), as an anionic dye. The higher adsorption capacity SO dye was observed at pH 9 and achieved almost 83% of removal, while RB5 dye adsorption on mica surface had the highest result, about 45% of removal efficiency, on pH of 3. In both cases, the main mechanism identified that drove this results is the electrostatic force of attraction between the adsorbent edge surface charge (pH-dependent) and the ionic nature (anionic or cationic) of the pollutant dyes particles. The preliminary adsorption experiments demonstrated that the raw grounded mica mineral has a greater potential associated with its application on cationic dye removal in wastewater. The present study aimed to detail the main characteristics of the mica mineral in order to evaluate the potential use of such mineral residues in the removal efficiency of contaminated wastewater.

Molecular Dynamics Simulation Study on the Interactions of Mixed Cationic/Anionic Collectors on Muscovite (001) Surface in Aqueous Solution

In this study, the adsorption mechanisms of dodecylamine hydrochloride(DDAHC), sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate(SDBS), and their mixed anionic/cationic collectors at ten different molar ratios on a muscovite (Mcv) surface in neutral aqueous solution were assessed by molecular dynamics simulations (MDS). According to the snapshot, interaction energy, radial distribution function (RDF), and density profile between the Mcv surface and collector molecules, the individual DDAHC collector was an effective collector for the flotation of Mcv. The molar ratio of anionic/cationic collectors was determined to be an essential factor in the flotation recovery of Mcv. The DDAHC collector was involved in the adsorption of the mixed anionic/cationic collectors on the Mcv (001) surface, whereas SDS and SDBS collectors were co-adsorbed with DDAHC. The mixed cationic/anionic collector showed the best adsorption on the Mcv surface in a molar ratio of 2. Additionally, SDBS, which has one more benzene ring than SDS, was more likely to form spherical micelles with DDAHC, thus resulting in better adsorption on the Mcv surface. The results of micro-flotation experiments indicated that the DDAHC collector could improve the flotation recovery of Mcv in neutral aqueous solution, which was in agreement with MDS-derived findings. In conclusion, DDAHC alone is the optimum collector for Mcv flotation under the neutral aqueous conditions, while the mixture of DDAHC and SDBS collectors (molar ratio = 2:1) exhibits the similar flotation performance.

Comparison and Mechanism Analysis of Three-Phase Contact Formation onto Hydrophilic/Hydrophobic Mineral Surfaces in the Presence of Cationic/Anionic Surfactants during Flotation Process

This article presents the dynamic process of the three-phase contact (TPC) formation by colliding bubbles onto muscovite and talc surfaces in water and two types of solutions including cationic CTAC surfactant (cetyltrimethyl ammoniumchloride) and anionic NaOL surfactant (sodium oleate). The TPC formation process was observed through the high-speed camera between bubbles and layered silicate minerals (hydrophilic muscovite and hydrophobic talc). It was found that the rupture of the liquid film between the bubbles and the mineral surface is a prerequisite for TPC formation. In the case of muscovite, TPC was formed only with cationic CTAC, and as the surfactant concentration increased, the time needed for TPC formation was shortened. Due to electrostatic repulsion, TPC did not occur in water and NaOL. However, for talc, TPC occurred both in water and in surfactant solutions. In contrast to muscovite, the time of TPC formation on the talc surface was prolonged with the increase in the surfactant concentration. It was concluded that hydrophobic attraction and electrostatic attraction between mineral surfaces and bubbles can significantly promote the localized foam film rupture, which was the main reason for the TPC appearance in water and surfactants. For the hydrophilic muscovite, CTAC adsorption improved the surface hydrophobicity; I3/I1 in fluorescence spectroscopy increased, and the micro-polarity faded, making TPC formation need more time. However, for the natural hydrophobic talc, the increasing surfactant adsorption decreased I3/I1 values and enhanced the local micro-polarity, causing the extension of time for TPC. Therefore, TPC formation for different minerals resulted from different reasons.

Self-Assembly of NaOL-DDA Mixtures in Aqueous Solution: A Molecular Dynamics Simulation Study

The self-assembly behaviors of sodium oleate (NaOL), dodecylamine (DDA), and their mixtures in aqueous solution were systematically investigated by large-scale molecular dynamics simulations, respectively. The interaction mechanisms between the surfactants, as well as the surfactants and solvent, were revealed via the radial distribution function (RDF), cluster size, solvent-accessible surface area (SASA), hydrogen bond, and non-bond interaction energy. Results showed that the molecules more easily formed aggregates in mixed systems compared to pure systems, indicating higher surface activity. The SASA values of DDA and NaOL decreased significantly after mixing, indicating a tighter aggregation of the mixed surfactants. The RDF results indicated that DDA and NaOL strongly interacted with each other, especially in the mixed system with a 1:1 molar ratio. Compared to van der Waals interactions, electrostatic interactions between the surfactant molecules were the main contributors to the improved aggregation in the mixed systems. Besides, hydrogen bonds were found between NaOL and DDA in the mixed systems. Therefore, the aggregates in the mixed systems were much more compact in comparison with pure systems, which contributed to the reduction of the repulsive force between same molecules. These findings indicated that the mixed NaOL/DDA surfactants had a great potential in application of mineral flotation.