Pyrrolidinone-based hypercrosslinked polymers for reversible capture of radioactive iodine

Construction of hydroxyl-functionalized hyper-crosslinked networks from polyimide for highly efficient iodine adsorption

The rapid development of nuclear energy posed a great threat to the environment and human health. Herein, two hydroxyl-functionalized hyper-crosslinked polymers (PIHCP-1 and PIHCP-2) containing different electron active sites have been synthesized via Friedel-Crafts alkylation reaction of the polyimides. The resulting polymers showed a micro/mesoporous morphology and good thermal and chemical stability. Rely on the high porosity and multi-active sites, the PIHCPs show an ultrahigh iodine uptake capacity reached 6.73 g g-1 and the iodine removal efficiency from aqueous solution also reaches 99.7%. Kinetic analysis demonstrates that the iodine adsorption on PIHCPs was happened on the heterogeneous surfaces in the form of multilayer chemisorption. Electrostatic potential (ESP) calculation proves the great contribution of hydroxyl groups on the iodine capture performance. In addition, the iodine capture efficiency of both adsorbents can be maintained over 91% after four cyclic experiments which ensures their good recyclability for further practical applications.

Photo-Modulating CO2 Uptake of Hypercross-linked Polymers Upcycled from Polystyrene Waste

Incorporating photo-switches into skeletal structures of microporous materials or as guest molecules yield photo-responsive materials for low-energy CO₂ capture but at the expense of lower CO₂ uptake. Here, we overcome this limitation by exploiting trans-cis photoisomerization of azobenzene loaded into the micropores of hypercross-linked polymers (HCPs) derived from waste polystyrene. Azobenzene in HCP pores reduced CO₂ uptake by 19 %, reaching 37.7 cm³  g^-1 , but this loss in CO₂ uptake was not only recovered by trans-cis photoisomerization of azobenzene, but also increased by 22 %, reaching 56.9 cm³  g^-1 , when compared to as-prepared HCPs. Computational simulations show that this increase in CO₂ uptake is due to photo-controlled increments in 10-20 Å micropore volume, i. e., adsorption sites and a photo-reversible positive dipole moment. Irradiating these HCPs with visual-range light reverted CO₂ uptake to 33 cm³  g^-1 . This shows that it is feasible to recycle waste polystyrene into advanced materials for low-energy carbon capture.

Two Facile Aniline-Based Hypercrosslinked Polymer Adsorbents for Highly Efficient Iodine Capture and Removal

Effective capture and safe disposal of radioactive iodine (¹²⁹I or ¹³¹I) during nuclear power generation processes have always been a worldwide environmental concern. Low-cost and high-efficiency iodine removal materials are urgently needed. In this study, we synthesized two aniline-based hypercrosslinked polymers (AHCPs), AHCP-1 and AHCP-2, for iodine capture in both aqueous and gaseous phases. They are obtained by aniline polymerization through Friedel-Crafts alkylation and Scholl coupling reaction, respectively, with high chemical and thermal stability. Notably, AHCP-1 exhibits record-high static iodine adsorption (250 wt%) in aqueous solution. In the iodine vapor adsorption, AHCP-2 presents an excellent total iodine capture (596 wt%), surpassing the most reported amorphous polymer adsorbents. The rich primary amine groups of AHCPs promote the rapid physical capture of iodine from iodine water and iodine vapor. Intrinsic features such as low-cost preparation, good recyclability, as well as excellent performance in iodine capture indicate that the AHCPs can be used as potential candidates for the removal of iodine from radioactive wastewater and gas mixtures.

An Azo-Group-Functionalized Porous Aromatic Framework for Achieving Highly Efficient Capture of Iodine

The strong radioactivity of iodine compounds derived from nuclear power plant wastes has motivated the development of highly efficient adsorbents. Porous aromatic frameworks (PAFs) have attracted much attention due to their low density and diverse structure. In this work, an azo group containing PAF solid, denoted as LNU-58, was prepared through Suzuki polymerization of tris-(4-(4,4,5,5-tetramethyl-1,3,2-dioxaborolan-2-yl)-phenyl)-amine and 3,5-dibromoazobenzene building monomers. Based on the specific polarity properities of the azo groups, the electron-rich aromatic fragments in the hierarchical architecture efficiently capture iodine molecules with an adsorption capacity of 3533.11 mg g−1 (353 wt%) for gaseous iodine and 903.6 mg g−1 (90 wt%) for dissolved iodine. The iodine uptake per specific surface area up to 8.55 wt% m−2 g−1 achieves the highest level among all porous adsorbents. This work illustrates the successful preparation of a new type of porous adsorbent that is expected to be applied in the field of practical iodine adsorption.

Synthesis of Electron-Rich Porous Organic Polymers via Schiff-Base Chemistry for Efficient Iodine Capture

As one of the main nuclear wastes generated in the process of nuclear fission, radioactive iodine has attracted worldwide attention due to its harm to public safety and environmental pollution. Therefore, it is of crucial importance to develop materials that can rapidly and efficiently capture radioactive iodine. Herein, we report the construction of three electron-rich porous organic polymers (POPs), denoted as POP-E, POP-T and POP-P via Schiff base polycondensations reactions between Td-symmetric adamantane knot and four-branched “linkage” molecules. We demonstrated that all the three POPs showed high iodine adsorption capability, among which the adsorption capacity of POP-T for iodine vapor reached up to 3.94 g·g⁻¹ and the removal rate of iodine in n-hexane solution was up to 99%. The efficient iodine capture mechanism of the POP-T was investigated through systematic comparison of Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) before and after iodine adsorption. The unique π-π conjugated system between imine bonds linked aromatic rings with iodine result in charge-transfer complexes, which explains the exceptional iodine capture capacity. Additionally, the introduction of heteroatoms into the framework would also enhance the iodine adsorption capability of POPs. Good retention behavior and recycling capacity were also observed for the POPs.

Pitch-based porous polymer beads for highly efficient iodine capture

The efficient and safe capture of volatile radioiodine is of great significance in the reprocessing of spent fuel. Herein, the millimeter-scale pitch-based hyper-cross-linked porous polymers@polyethersulfone (PHCP@PES) composite beads were firstly synthesized for the removal of volatile iodine and methyl iodide. PHCP@PES beads exhibit high iodine vapor and methyl iodide uptake capacities of 770.0 mg/g and 186.5 mg/g, respectively. More impressively, the uptake capacities of PHCP@PES (744.5 mg/g for iodine vapor and 180 mg/g for methyl iodide) remained almost unchanged after treatment with 3 mol/L of nitric acid. The rich interconnected pore structure of PHCP@PES promotes the rapid physical capture of iodine and methyl iodide. Intrinsic features such as low-cost preparation, good mechanical properties as well as thermal, acid stability and excellent performance in iodine capture indicate that PHCP@PES can be used as a potential candidate for the removal of radioactive iodine in the exhaust gas stream of post-treatment plants.

Barbituric and thiobarbituric acid-based UiO-66-NH2 adsorbents for iodine gas capture: Characterization, efficiency and mechanisms

Efficient iodine gas capture is necessitated in many industries like spent nuclear fuel off-gas treatment in view of environmental protection and resource recycling. However, the adsorption efficiency and stability of the current adsorbents are limited. In the present work, efficient and stable barbituric and thiobarbituric acid-based UiO-66-NH₂ adsorbents (i.e., UiO-66-NH-B.D and UiO-66-NH-T.D, respectively) have been synthesized by post-synthetic covalent modification. Characterization approaches, including SEM-EDS, TEM, XRD, FTIR, XPS, ¹H NMR, TGA and BET, are used to obtain information on the properties and adsorption mechanisms of these metal-organic framework (MOF) adsorbents. The kinetics and mechanisms involved are studied in detail. The treatment efficiency and recyclability of the adsorbents are checked and compared with the adsorbents reported in previous works. The results show that the current adsorbents are potentially suitable for efficient iodine gas capture. High maximum iodine adsorption amount by UiO-66-NH-B.D and UiO-66-NH-T.D (1.17 and 1.33 g/g) was achieved under 75 °C. These new adsorbents are thermally stable for iodine adsorption and regenerated and reused with good performance. The adsorption mechanisms were revealed based on experimental results, indicating that iodine is adsorbed by both physisorption and chemisorption.

Rapid iodine capture from radioactive wastewater by green and low-cost biomass waste derived porous silicon–carbon composite

The effective and safe capture and storage of radioactive iodine (¹²⁹I or ¹³¹I) are of significant importance during nuclear waste storage and nuclear energy generation. Herein, a porous silicon–carbon (pSi–C) composite derived from paper mill sludge (PMS) is synthesized and used for rapid iodine capture. The influences of the activator type, the impregnation ratio of the paper mill sludge to the activator, carbonization temperature, and carbonization time on the properties of the pSi–C composite are investigated. The pSi–C composite produced in the presence of ZnCl₂ as the activator and at an impregnation ratio of 1 : 1, a carbonization temperature of 550 °C, and a carbonization time of 90 min has a surface area of 762.13 m² g⁻¹. The as-synthesized pSi–C composite exhibits promising iodine capture performance in terms of superior iodine adsorption capacity (q_t) of around 250 mg g⁻¹ and rapid equilibrium adsorption with in 15 min. The devised method is environmentally friendly and inexpensive and can easily be employed for the large-scale production of porous silicon-activated carbon composites with excellent iodine capture and storage from iodine-contaminated water.

The effective and safe capture and storage of radioactive iodine (¹²⁹I or ¹³¹I) are of significant importance during nuclear waste storage and nuclear energy generation.

Synthesis of Conjugated Mesoporous Hyper-cross-linked Polymers for Efficient Capture of Dibenzothiophene and Iodine

Porous organic polymers have recently received great attention because of their promising applications in the removal of thiophene compounds in liquid fuels and for the nuclear waste (such as radioactive iodine isotopes) treatments. Herein, a series of conjugated mesoporous hyper-cross-linked polymers (CMHPs) were prepared through our newly developed silicon-promoted cationic polymerization in a straightforward manner. The CMHPs exhibited extended π-conjugation, intrinsic porosity, high surface area, and excellent physicochemical stability. They showed an outstanding dibenzothiophene uptake capacity of ∼1335 mg g^-1, which far exceeded many reported porous organic polymers. Meanwhile, these CMHPs showed high adsorption capacity for iodine vapor. Altogether, the CMHPs prepared by the facile and metal-free cationic reactions have great potential in adsorption of harmful substances and environmental protection.

Hazardous wastes treatment technologies

A review of the literature published in 2019 on topics related to hazardous waste management in water, soils, sediments, and air. The review covered treatment technologies applying physical, chemical, and biological principles for the remediation of contaminated water, soils, sediments, and air. PRACTICAL POINTS: This report provides a review of technologies for the management of waters, wastewaters, air, sediments, and soils contaminated by various hazardous chemicals including inorganic (e.g., oxyanions, salts, and heavy metals), organic (e.g., halogenated, pharmaceuticals and personal care products, pesticides, and persistent organic chemicals) in three scientific areas of physical, chemical, and biological methods. Physical methods for the management of hazardous wastes including general adsorption, sand filtration, coagulation/flocculation, electrodialysis, electrokinetics, electro-sorption ( capacitive deionization, CDI), membrane (RO, NF, MF), photocatalysis, photoelectrochemical oxidation, sonochemical, non-thermal plasma, supercritical fluid, electrochemical oxidation, and electrochemical reduction processes were reviewed. Chemical methods including ozone-based, hydrogen peroxide-based, potassium permanganate processes, and Fenton and Fenton-like process were reviewed. Biological methods such as aerobic, anoxic, anaerobic, bioreactors, constructed wetlands, soil bioremediation and biofilter processes for the management of hazardous wastes, in mode of consortium and pure culture were reviewed. Case histories were reviewed in four areas including contaminated sediments, contaminated soils, mixed industrial solid wastes and radioactive wastes.

Porous MOF-808@PVDF beads for removal of iodine from gas streams

The removal of radioiodine from the exhaust gas streams produced in spent fuel reprocessing plants is of paramount importance for the nuclear fuel cycle's security. Here, millimeter-sized poly(vinylidene fluoride) (PVDF) composites containing zirconium-based metal–organic frameworks, MOF-808, were synthesized by a facile phase inversion method to adsorb the volatile iodine. MOF-808@PVDF composites have inherited the crystallinity and pore accessibility of MOF-808, as well as its outstanding iodine capture performance. The MOF-808@PVDF composite beads containing 70 wt% MOFs, exhibited ultrahigh iodine adsorption capacity, 1.42 g g⁻¹ at 80 °C, much higher than other millimeter-sized adsorbents reported in the literature. Raman mapping suggests that the negative iodine ions were formed at the early stage of iodine adsorption, while the close-packed iodine molecules were subsequently trapped in the frames. Using dynamic adsorption, the influences of iodine concentration, operating temperature and humidity were analyzed to evaluate its application potential in industrial conditions. The iodine adsorption capacity could reach 1.36 g g⁻¹ at 80 °C, 100 °C and 120 °C in flow gas. And the elevated temperature (120 °C) is beneficial to accelerating the mass transfer of iodine vapor, as well as slightly inhibiting the competitive adsorption of water molecules under humidity. Besides, only one-third of the loaded iodine was released in nitrogen purging after saturated adsorption. The remaining majority was trapped firmly by the beads due to their strong interactions with the frameworks. This work highlights the millimeter-sized MOF-808@polymer composite beads with ultrahigh iodine adsorption capacity, providing experimental references for their application in radioiodine removal from hot and moist streams.

Porous millimeter-sized MOF-808@PVDF composite beads with ultrahigh iodine adsorption capacity for capture of radioiodine from gas streams.

Carbazole-Bearing Porous Organic Polymers with a Mulberry-Like Morphology for Efficient Iodine Capture

Three kinds of carbazole-based porous organic polymers were successfully prepared via simple Friedel-Crafts alkylation of 1,3,5-tri(9-carbazolyl)-benzene. External cross-linking agents named 1,4-bis(chloromethyl)-benzene, cyanuric chloride, and 1,4-dimethoxybenzene were selected, and the derived polymers (denoted as CSU-CPOPs-1, CSU-CPOPs-2, and CSU-CPOPs-3) gave high surface areas (up to 1032 m²/g) and good stability. Interestingly, varying the nature of "knitting" agents led to an unprecedented morphology evolution, and it is worth noting that a mulberry-like morphology was observed for the case of 1,4-bis(chloromethyl)-benzene. Taking advantage of the unique mulberry-like morphology as well as abundant porosity, CSU-CPOPs-1 showed ultrahigh iodine vapor adsorption performance with a capacity of 494 wt % at 348 K and 1 bar, which is the highest value reported to date for amorphous polymers. This study presented a feasible way to develop efficient iodine sorbents with tunable morphologies for addressing environmental issues.

Magnetic cucurbit[6]uril-based hypercrosslinked polymers for efficient enrichment of ubiquitin

The design and preparation of magnetic cucurbit[6]uril hypercrosslinked with polymers are described. The materials have a large specific surface, abundant mesopores and cavities, and display superparamagnetism. They were applied to the enrichment of ubiquitinated peptides from standard protein digests. Following desorption with 0.15% TFA, the peptides were quantified by MALDI-TOF MS. The method has a detection limit of 2 fmol·μL^-1 and a mass ratio selectivity of 1:5000 as shown for ubiquitin and bovine serum albumin. The materials enable selective capture of ubiquitinated peptides from genuine samples comprising of oyster mushroom and human serum. This demonstrates their potential for the analysis of low-level ubiquitin in complex samples. Graphical abstract Schematic presentation for the synthesis of magnetic cucurbit[6]urils hypercrosslinked polymers (MagCB[6]-HCPs).