Polishing monoclonal antibody using pH-responsive TiO2/polysulfone membrane in dual size-exclusion strategy

Effects of additive dosage and coagulation bath pH on amphoteric fluorocarbon special surfactant (FS-50) blend PVDF membranes

Amphiphilic copolymers containing hydrophilic and hydrophobic blocks represented by surfactants have proven to be more effective for modifying membranes than hydrophilic copolymers. However, studies on the effects of additive and coagulation bath pH on the morphology and properties of surfactant-modified membranes have rarely been reported. Hence, this study aims to investigate the effects of the additive dosage and the coagulation bath pH on the mechanisms of phase inversion and performance improvement of amphoteric fluorocarbon special surfactant (FS-50) blended PVDF membranes. It was observed that the pure water flux increased from 114.68 LMH/bar of the original membrane M0 to 205.02 LMH/bar of the blend membrane M1, and then to 615.88 LMH/bar of the coagulation-bath-regulated membrane MPH9 with a high BSA rejection rate of 90.86%, showing a two-stage jump. The addition of FS-50 promoted the instantaneous phase inversion of the membrane, allowing the blend membrane to exhibit a higher proportion of pore characteristics and stronger permeability. After that, the mechanisms of the membrane phase inversion process affected by the coagulation bath pH were interpreted according to the pH-response characteristics of FS-50 in terms of charge repulsion effect and compressed double-electron layer effect. Furthermore, the cross-sectional morphology and the surface structure of the membrane prepared in acidic and alkaline coagulation baths were significantly affected by the pH of the coagulation bath, exhibiting different features. For one, the porosity of the membranes gradually decreased as the acidity and alkalinity of the coagulation bath increased, and the membrane MPH9 exhibited both maximum surface and overall porosity. For another, the coagulation bath pH did not negatively affect the contact angle, surface roughness and tensile strength of the membranes. Overall, adjusting the dosage of FS-50 and the pH of the coagulation bath is a promising approach to greatly enhance membrane performance.

New Understanding of the Difference in Filtration Performance between Anatase and Rutile TiO2 Nanoparticles through Blending into Ultrafiltration PSF Membranes

The blending of nanomaterials into a polymeric matrix is a method known for its ability, under certain circumstances, to lead to an improvement in membrane properties. TiO₂ nanoparticles have been used in membrane research for the last 20 years and have continuously shown promise in this field of research. Polysulfone (PSf) membranes were obtained through the phase inversion method, with different TiO₂ nanoparticle concentrations (0, 0.1, 0.5, and 1 wt.%) and two types of TiO₂ crystalline structure (anatase and rutile), via the addition of commercially available nanopowders. Research showed improvement in all studied properties. In particular, the 0.5 wt.% TiO₂ rutile membrane recorded an increase in permeability of 139.7% compared to the control membrane. In terms of overall performance, the best nanocomposite membrane demonstrated a performance index increase of 71.1% compared with the control membrane.

Sustainable cultivation of Navicula incerta using cellulose-based scaffold incorporated with nanoparticles in air-liquid interface cultivation system

Microalgae cultivation using open cultivation systems requires large area and it is susceptible to contamination as well as weather changes. Meanwhile, the closed systems require large capital investment, and they are susceptible to the build-up of dissolved oxygen. Air-liquid interface culture systems with low water-footprint, but high packing density can be used for microalgae cultivation if low-cost culture scaffolds are available. In this study, cellulose-based scaffolds were synthesized using NaOH/urea aqueous solution as the solvent. Titanium dioxide (TiO₂), silica gel and polyethylene glycol 1000 (PEG 1000) nanoparticles were added into the membrane scaffolds to increase the hydrophilicity of nutrient absorbing to support the growth of microalgae. The membrane scaffolds were characterized by FTIR, SEM, contact angle, porosity and porometry. All three nanoparticles additives showed their ability in reducing the contact angle of membrane scaffolds from 63.4 ± 2.3° to a range of 52.6 ± 1.2° to 38.8 ± 1.5° due to the hydrophilic properties of the nanoparticles. The decreasing in pore size when nanoparticles were added did not affect the porosity of membrane scaffolds. Cellulose membrane scaffold with TiO₂ showed the highest percentage of microalgae Navicula incerta growth rate of 22.1% because of the antibacterial properties of TiO₂ in lowering the risk of cell contamination and enhancing the growth of N. incerta. The results exhibited that cellulose-based scaffold with TiO₂ added could be an effective support in plant cell culture field.

Control of the pore size of honeycomb polymer film from micrometers to nanometers via substrate-temperature regulation and its application to photovoltaic and heat-resistant polymer films

Honeycomb porous polystyrene (PS) films with an aspect ratio of pore depth to pore diameter at approximately 1.0 were fabricated using the breath figure (BF) method. Two modes of water droplet coalescence in the pore growth were observed in real-time by optical microscopy. Pore size significantly increases with the increase in humidity and the decrease in substrate temperature. The porous pattern could emerge even at room temperature under high humidity of 80%. Boiling point and solvent density significantly influence the pore distribution and pore depth. Chloroform and tetrahydrofuran achieve more uniform hexagonal patterns than benzene and dichloromethane. Subsequently, to obtain nanometer porous PS film, the fast-evaporation BF process was designed by regulating the gradient substrate temperature and evaporation time, and porous mesoscopic PS film was obtained. The minimum pore diameter and corresponding pore depth are about 120 nm and 27 nm, respectively. Finally, the fast-evaporation BF process was applied to the honeycomb film formation of photovoltaic polymer poly(3-hexylthiophene) (P3HT), and the heat-resistant polymers polysulfone (PSF) and polyimide (PI).