Ultra-thin double Janus nanofiltration membrane for separation of Li+ and Mg2+: “Drag” effect from carboxyl-containing negative interlayer

Luminescence "Turn-On" Sensing of Brain Natriuretic Peptide (BNP) - Dilated Cardiomyopathy Biomarker Based on the MoS2 Nanosheet Quenched Terbium Citrate Complex

Dilated cardiomyopathy (DCM), known as myocardial metabolic dysfunction, is recognized as a clinical condition characterized by left ventricular dilation or improper contraction of cardiac muscles in the absence of coronary atherosclerosis and hypertension. It is an independent risk factor for cardiac function caused by a hyperglycemic condition in diabetic patients leading to heart failure (HF), which renders the early diagnosis of DCM highly challenging. Hence, detection of early diagnostic biomarkers in blood serum to identify DCM conditions is quite requisite. Brain natriuretic peptide (BNP) is a well-recognized biomarker for heart failure and reported as an early diagnostic biomarker for DCM. In this work, we developed a terbium citrate based MoS2 nanosheet (NS) coupled immunoprobe for the sensitive detection of BNP. The antibody conjugated Tb-citrate complex exhibits green fluorescence, which is quenched by the introduction of MoS2 NS. On subsequent addition of antigen BNP, the fluorescence is enhanced because of specific antigen-antibody interaction. The probe is selective and sensitive toward BNP in a linear range from 30.76 to 849.85 pg/mL with a low LOD of 3.87 pg/mL. The probe is validated in spiked human serum samples with good recovery percentage.

High-Strength MOF-Based Polymer Electrolytes with Uniform Ionic Flow for Lithium Dendrite Suppression

The uneven formation of lithium dendrites during electroplating/stripping leads to a decrease in the utilization of active lithium, resulting in poor cycling stability and posing safety hazards to the battery. Herein, introducing a 3D continuously interconnected zirconium-based metal-organic framework (MOF808) network into a polyethylene oxide polymer matrix establishes a synergistic mechanism for lithium dendrite inhibition. The 3D MOF808 network maintains its large pore structure, facilitating increased lithium salt accommodation, and expands anion adsorption at unsaturated metal sites through its diverse large-space cage structure, thereby promoting the flow of Li+. Infrared-Raman and synchrotron small-angle X-ray scattering results demonstrate that the transport behavior of lithium salt ion clusters at the MOF/polymer interface verifies the increased local Li+ flux concentration, thereby raising the mobility number of Li+ to 0.42 and ensuring uniform Li+ flux distribution, leading to dendrite-free and homogeneous Li+ deposition. Furthermore, nanoindentation tests reveal that the high modulus and elastic recovery of MOF-based polymer electrolytes contribute to forming a robust, dendrite-resistant interface. Consequently, in symmetric battery systems, the system exhibits minimal overpotential, merely 35 mV, while maintaining stable cycling for over 1800 h, achieving low-overpotential lithium deposition. Moreover, it retains redox stability under high voltages up to 5.3 V.

Polyamide Membranes with Tunable Surface Charge Induced by Dipole-Dipole Interaction for Selective Ion Separation

Nanofiltration (NF) has the potential to achieve precise ion-ion separation at the subnanometer scale, which is necessary for resource recovery and a circular water economy. Fabricating NF membranes for selective ion separation is highly desirable but represents a substantial technical challenge. Dipole-dipole interaction is a mechanism of intermolecular attractions between polar molecules with a dipole moment due to uneven charge distribution, but such an interaction has not been leveraged to tune membrane structure and selectivity. Herein, we propose a novel strategy to achieve tunable surface charge of polyamide membrane by introducing polar solvent with a large dipole moment during interfacial polymerization, in which the dipole-dipole interaction with acyl chloride groups of trimesoyl chloride (TMC) can successfully intervene in the amidation reaction to alter the density of surface carboxyl groups in the polyamide selective layer. As a result, the prepared positively charged (PEI-TMC)-NH2 and negatively charged (PEI-TMC)-COOH composite membranes, which show similarly high water permeance, demonstrate highly selective separations of cations and anions in engineering applications, respectively. Our findings, for the first time, confirm that solvent-induced dipole-dipole interactions are able to alter the charge type and density of polyamide membranes and achieve tunable surface charge for selective and efficient ion separation.

Electronanofiltration Membranes with a Bilayer Charged Structure Enable High Li+/Mg2+ Selectivity

Achieving separation of lithium and magnesium with similar radii is crucial for the current lithium extraction technology from salt lakes, which usually possess a high lithium-to-magnesium ratio. Herein, we proposed the facile sequential interfacial polymerization (SIP) approach to construct electronanofiltration membranes (ENFMs) with a bilayer charged structure consisting of a high positively charged surface and a negatively charged sublayer. The trimesoyl chloride (TMC) concentration was adjusted to enhance the -COOH content and negative charge of the polyamide sublayer to promote Li+ migration, and then the quaternized polyethylenimine was introduced to the membrane surface by the SIP process to increase the positive charge density on the surface of the ENFMs, which would block the migration of Mg2+ and enhance the Li+/Mg2+ selectivity of the ENFMs. The optimal quaternary-modified ENFMs achieved outstanding selectivity for Li+/Mg2+ (49.85) and high Li+ flux (4.10 × 10-8 mol cm-2 s-1) at a current density of 10 mA cm-2. Moreover, in simulated brines with low lithium concentration and high Mg2+/Li+ ratio, the optimal ENFMs also displayed elevated Li+/Mg2+ selectivity (>45), highlighting the substantial promise of the membranes for practical applications.

Self-assembled dendrimer polyamide nanofilms with enhanced effective pore area for ion separation

Membrane technology using well-defined pore structure can achieve high ion purity and recovery. However, fine-tuning the inner pore structure of the separation nanofilm to be uniform and enhance the effective pore area is still challenging. Here, we report dendrimers with different peripheral groups that preferentially self-assemble in aqueous-phase amine solution to facilitate the formation of polyamide nanofilms with a well-defined effective pore range and uniform pore structure. The high permeabilities are maintained by forming asymmetric hollow nanostripe nanofilms, and their well-designed ion effective separation pore ranges show an enhancement, rationalized by molecular simulation. The self-assembled dendrimer polyamide membrane provides Cl-/SO42- selectivity more than 17 times that of its pristine polyamide counterparts, increasing from 167.9 to 2883.0. Furthermore, the designed membranes achieve higher Li purity and Li recovery compared to current state-of-the-art membranes. Such an approach provides a scalable strategy to fine-tune subnanometre structures in ion separation nanofilms.

Positively Charged Polyamine Nanofiltration Membrane for Precise Ion-Ion Separation

Positively charged nanofiltration (NF) membranes offer enormous potential for lithium-magnesium separation, hard water softening, and heavy metal removal. However, fundamental performance limitations for these applications exist in conventional polyamide-based NF membranes due to the negatively charged surface and low ion-ion selectivity. We hereby innovatively develop an advanced positively charged polyamine-based NF membrane built by the nucleophilic substitution of bromine and amine groups for precise ion-ion separation. Specifically, polyethylenimine (PEI) and 1,3,5-tris(bromomethyl)benzene (TBB) are interfacially polymerized to generate an amine-linked PEI-TBB selective layer with an ultrathin thickness of ∼95 nm, an effective pore size of 6.5 Å, and a strong positively charged surface with a zeta potential of +20.9 mV at pH 7. The PEI-TBB composite membrane achieves a water permeance of 4.2 L·m-2·h-1·bar-1, various divalent salt rejections above 90%, and separation factors above 15 for NaCl/MgCl2 and LiCl/MgCl2 mixed solutions. A three-stage NF process is implemented to achieve a Mg2+/Li+ mass ratio sharply decreasing from 50 to 0.11 with a total separation factor (SLi,Mg) of 455. Furthermore, the polyamine-based NF membrane exhibits excellent operational stability under continuous filtration and high operational pressure, demonstrating great application potential for precise ion-ion separation.

Sustainable Lithium Recovery from Hypersaline Salt-Lakes by Selective Electrodialysis: Transport and Thermodynamics

Evaporative technology for lithium mining from salt-lakes exacerbates freshwater scarcity and wetland destruction, and suffers from protracted production cycles. Electrodialysis (ED) offers an environmentally benign alternative for continuous lithium extraction and is amenable to renewable energy usage. Salt-lake brines, however, are hypersaline multicomponent mixtures, and the impact of the complex brine-membrane interactions remains poorly understood. Here, we quantify the influence of the solution composition, salinity, and acidity on the counterion selectivity and thermodynamic efficiency of electrodialysis, leveraging 1250 original measurements with salt-lake brines that span four feed salinities, three pH levels, and five current densities. Our experiments reveal that commonly used binary cation solutions, which neglect Na+ and K+ transport, may overestimate the Li+/Mg2+ selectivity by 250% and underpredict the specific energy consumption (SEC) by a factor of 54.8. As a result of the hypersaline conditions, exposure to salt-lake brine weakens the efficacy of Donnan exclusion, amplifying Mg2+ leakage. Higher current densities enhance the Donnan potential across the solution-membrane interface and ameliorate the selectivity degradation with hypersaline brines. However, a steep trade-off between counterion selectivity and thermodynamic efficiency governs ED's performance: a 6.25 times enhancement in Li+/Mg2+ selectivity is accompanied by a 71.6% increase in the SEC. Lastly, our analysis suggests that an industrial-scale ED module can meet existing salt-lake production capacities, while being powered by a photovoltaic farm that utilizes <1% of the salt-flat area.

Comparison of the Mg2+-Li+ Separation of Different Nanofiltration Membranes

Nanofiltration application for the separation of Mg2+-Li+ from salt-lake brines was attempted in the present work. Four different nanofiltration membranes identified in the manuscript as DL, DK, NF-270, and NF-90 were used to treat salt brine with a magnesium to lithium ratio (MLR) of 61, additionally contaminated by the other ions such as Na+, K+, Ca2+, etc. The effect of the dilution factor, operating pressure, circulation rate, and feed pH were assessed to identify the optimal operating conditions for each membrane based on the retention efficiency of each ion. The results showed an insignificant effect of Ca2+ on the retention performance of Mg2+-Li+. Na+ and K+ had a smaller hydration radius and larger diffusion coefficient, which competed with Li+ and altered the separation of Mg2+-Li+. Under the optimal conditions (dilution factor: 40; operating pressure: 1.2 MPa; circulation flow rate: 500 L/h; pH: 7), the retention efficiency of lithium was as low as 5.17%, separation factor (SF) was as low as 0.074, and the MLR in the permeate reduced to 0.088.

Janus membranes at the water-energy nexus: A critical review

Membrane technology has emerged as a highly efficient strategy for alleviating water and energy scarcity globally. As the key component, the membrane plays a fatal role in different membrane systems; however, traditional membranes still suffer from shortcomings including low permeability, low selectivity, and high fouling tendency. Janus membranes are promising to overcome those shortcomings and appealing for applications in the realm of water-energy nexus, due to their special transport behaviors and separation properties as a result of their unique asymmetric wetting or surface charge properties. Recently, numerous research studies have been conducted on the design, fabrication, and application of Janus membranes. In this review, we aim to provide a state-of-the-art summary and a critical discussion on the research advances of Janus membranes at the water-energy nexus. The innovative design strategies of different types of Janus membranes are summarized and elucidated in detail. The fundamental working principles of various Janus membranes and their applications in oil/water separation, membrane distillation, solar evaporation, electrodialysis, nanofiltration, and forward osmosis are discussed systematically. The mechanisms of directional transport properties, switchable permeability, and superior separation properties of Janus membranes in those different applications are elucidated. Lastly, future research directions and challenges are highlighted in improving Janus membrane performance for various membrane systems.

Lithium Concentration from Salt-Lake Brine by Donnan-Enhanced Nanofiltration

Membranes offer a scalable and cost-effective approach to ion separations for lithium recovery. In the case of salt-lake brines, however, the high feed salinity and low pH of the post-treated feed have an uncertain impact on nanofiltration's selectivity. Here, we adopt experimental and computational approaches to analyze the effect of pH and feed salinity and elucidate key selectivity mechanisms. Our data set comprises over 750 original ion rejection measurements, spanning five salinities and two pH levels, collected using brine solutions that model three salt-lake compositions. Our results demonstrate that the Li⁺/Mg²⁺ selectivity of polyamide membranes can be enhanced by 13 times with acid-pretreated feed solutions. This selectivity enhancement is attributed to the amplified Donnan potential from the ionization of carboxyl and amino moieties under low solution pH. As feed salinities increase from 10 to 250 g L^-1, the Li⁺/Mg²⁺ selectivity decreases by ∼43%, a consequence of weakening exclusion mechanisms. Further, our analysis accentuates the importance of measuring separation factors using representative solution compositions to replicate the ion-transport behaviors with salt-lake brine. Consequently, our results reveal that predictions of ion rejection and Li⁺/Mg²⁺ separation factors can be improved by up to 80% when feed solutions with the appropriate Cl^-/SO₄^2- molar ratios are used.

One-Step Construction of the Positively/Negatively Charged Ultrathin Janus Nanofiltration Membrane for the Separation of Li+ and Mg2

To coordinate the trade-off between the separation and permeation of the nanofiltration membrane for the separation of Mg²⁺/Li⁺, we regulated poly(ethyleneimine)/piperazine interface polymerization parameters to construct a positively/negatively charged ultrathin Janus nanofiltration membrane at a free aqueous-organic interface. At the optimized interfacial polymerization parameters, 0.03 wt % of piperazine reacted with trimethylbenzene chloride prior to poly(ethyleneimine), forming a primary polyamide layer with fewer defects or limiting large-scale defects of the polyamide layer. The controlled subsequent reaction of poly(ethyleneimine) and trimethylbenzene chloride results in a Janus nanofiltration membrane, with one side enriched with the carboxyl groups, the other side enriched with the amine groups, and a dense polyamide structure in the middle. Under the optimum conditions, the positive potential of the rear surface of the prepared membrane was 14.57 mV, and the water contact angle reached 71.31°, while the negative potential of the front surface was -25.48 mV, and the water contact angle was 12.93°, confirming a Janus membrane with opposite charges and large hydrophilicity differences in the front and rear surfaces. With a high cross-linking degree, a 40 nm thick polyamide layer is 29.09% more thinner than the traditional polyamide membrane. The ultrathin Janus nanofiltration membrane showed an excellent separation factor (S_Li,Mg of 18.26), stability, and water permeability flux (10.6 L·m^-2·h^-1·bar^-1). The rejections to MgCl₂, CaCl₂, MgSO₄, and Na₂SO₄ are measured above 90% at a nearly constant permeability of 10.6 L·m^-2·h^-1·bar^-1, particularly stable rejections to MgCl₂ and Na₂SO₄.

Planting Anion Channels in a Negatively Charged Polyamide Layer for Highly Selective Nanofiltration Separation

A nanofiltration (NF) membrane with high salt permeation and high retention of small organics is appealing for the treatment of high-salinity organic wastewater. However, the conventional negatively charged NF membranes commonly show high retention of divalent anions (e.g., SO₄^2-), and the reported positively charged NF membranes normally suffer super low selectivity for small organics/Na₂SO₄ and high fouling potential. In this work, we propose a novel "etching-swelling-planting" strategy assisted by interfacial polymerization and mussel-inspired catecholamine chemistry to prepare a mix-charged NF membrane. By X-ray photoelectron spectroscopy depth profiling and pore size distribution analysis, it was found that such a strategy could not only deepen the positive charge distribution but also narrow the pore size. Molecular dynamics confirm that the planted polyethyleneimine chains play an important role to relay SO₄^2- ions to facilitate their transport across the membrane, thus reversing the retention of Na₂SO₄ and glucose (43 vs 71%). Meanwhile, due to the high surface hydrophilicity and smoothness as well as the preservation of abundant negatively charged groups (-OH and -COOH) inside the separation layer, the obtained membrane exhibited excellent antifouling performance, even for the coking wastewater. This study advances the importance of vertical charge distribution of NF membranes in separation selectivity and antifouling performance.

Recent advances in thin film nanocomposite membranes containing an interlayer (TFNi): fabrication, applications, characterization and perspectives

Polyamide (PA) reverse osmosis and nanofiltration membranes have been applied widely for desalination and wastewater reuse in the last 5-10 years. A novel thin-film nanocomposite (TFN) membrane featuring a nanomaterial interlayer (TFNi) has emerged in recent years and attracted the attention of researchers. The novel TFNi membranes are prepared from different nanomaterials and with different loading methods. The choices of intercalated nanomaterials, substrate layers and loading methods are based on the object to be treated. The introduction of nanostructured interlayers improves the formation of the PA separation layer and provides ultrafast water molecule transport channels. In this manner, the TFNi membrane mitigates the trade-off between permeability and selectivity reported for polyamide composite membranes. In addition, TFNi membranes enhance the removal of metal ions and organics and the recovery of organic solvents during nanofiltration and reverse osmosis, which is critical for environmental ecology and industrial applications. This review provides statistics and analyzes the developments in TFNi membranes over the last 5-10 years. The latest research results are reviewed, including the selection of the substrate and interlayer materials, preparation methods, specific application areas and more advanced characterization methods. Mechanistic aspects are analyzed to encourage future research, and potential mechanisms for industrialization are discussed.

Photocatalytic nanocomposite membranes for environmental remediation

We report the design and one-pot synthesis of Ag-doped BiVO₄embedded in reduced graphene oxide (BiVO₄:Ag/rGO) nanocomposites via a hydrothermal processing route. The binary heterojunction photocatalysts exhibited high efficiency for visible light degradation of model dyes and were correspondingly used for the preparation of photocatalytic membranes using polyvinylidene fluoride (PVDF) or polyethylene glycol (PEG)-modified polyimide (PI), respectively. The surface and cross-section images combined with elemental mapping illustrated the effective distribution of the nanocomposites within the polymeric membranes. Photocatalytic degradation efficiencies of 61% and 70% were achieved after 5 h of visible light irradiation using BiVO₄:Ag/rGO@PVDF and BiVO₄:Ag/rGO@PI (PEG-modified) systems, respectively. The beneficial photocatalytic performance of the BiVO₄:Ag/rGO@PI (PEG-modified) membrane is explained by the higher hydrophilicity due to the PEG modification of the PI membrane. This work may provide a rational and effective strategy to fabricate highly efficient photocatalytic nanocomposite membranes with well-contacted interfaces for environmental purification.

Biofibrous nanomaterials for extracting strategic metal ions from water

Strategic metals play an indispensable role in the related industries. Their extraction and recovery from water are of great significance due to both their rapid consumption and environmental concern. Biofibrous nanomaterials have shown great advantages in capturing metal ions from water. Recent progress in extraction of typical strategic metal ions such as noble metal ions, nuclear metal ions, and Li-battery related metal ions is reviewed here using typical biological nanofibrils like cellulose nanofibrils, chitin nanofibrils, and protein nanofibrils, as well as their assembly forms like fibers, aerogels/hydrogels, and membranes. An overview of advances in material design and preparation, extraction mechanism, dynamics/thermodynamics, and performance improvement in the last decade is provided. And at last, we propose the current challenges and future perspectives for promoting biological nanofibrous materials toward extracting strategic metal ions in practical conditions of natural seawater, brine, and wastewater.

Fabrication of High-Performance Nanofiltration Membrane Using Polydopamine and Carbon Nitride as the Interlayer

In order to recover lithium from brine with a high Mg2+/Li+ ratio, a positively charged nanofiltration (NF) membrane was prepared by depositing polydopamine (PDA)-coated graphitic carbon nitride (g-C3N4) as the interlayer (PDA-g-C3N4) and the interfacial polymerization (IP) of polyethyleneimine (PEI) and trimesoyl chloride (TMC) was carried out. Under optimal conditions, the water contact angle of the composite membrane is only 55.5° and the isoelectric point (IEP) is 6.01. The final positively charged NF membrane (M5) exhibits high permeance (10.19 L·m−2·h−1·bar−1) and high rejection of Mg2+ (98.20%) but low rejection of Li+ (13.33%). The separation factor (SF) is up to 48.08, and the Mg2+/Li+ ratio of the permeate is 0.036 in the simulated brine. In conclusion, the M5 membrane shows a good separation performance for salt lake brine (SF = 12.79 and Mg2+/Li+ ratio of the permeate = 1.43) and good fouling resistance. Therefore, the positively charged M5 membrane with PDA-g-C3N4 as the interlayer has the potential to be used for the recovery of lithium from brine.

Reduce and concentrate graphene quantum dot size via scissors: vacancy, pentagon-heptagon and interstitial defects in graphite by gamma rays

Graphene quantum dots (GQDs) with ultrafine particle size and centralized distribution have advantages of small size, narrow size distribution and large specific surface area, which make it be better applied in bioimaging, drug delivery and so on. In our research, we used graphite irradiated byγ-rays to successfully prepare GQDs with ultrafine particle size, narrow size distribution and high quantum yields through solvothermal method. Vacancy defects, pentagon-heptagon defects and interstitial defects were introduced to graphite structure after irradiation, which caused the abundance and concentrated distribution of defects. The defects generated by irradiation could damage the lattice structure of graphite to make it easy for introduction of C-O-C inside graphite sheets. The oxygen-containing functional groups in graphene oxide (GO) increased and centrally distributed after irradiation in graphite, especially for C-O-C group, which were beneficial for cutting of GO and grafting of functional groups in GQDs. Therefore, average size of GQDs was successfully reduced to 1.43 nm and concentrated to 0.6-2.4 nm. After irradiation in graphite, the content of carbonyl and C-N in GQDs had a promotion, which suppressed non-radiative recombination and upgraded the quantum yields to 13.9%.

"Self-doping" defect engineering in SnP3@gamma-irradiated hard carbon anode for rechargeable sodium storage

Reasonable design of defect engineering in the electrode materials for sodium-ion batteries (SIBs) can significantly optimize battery performance. Here, compared with the traditional "foreign-doping" defects method, we report an innovative gamma-irradiation technique to introduce the "self-doping" defects in the popcorn hard carbon (HC). Considering the advantages of adsorption-intercalation-alloying sodium storage mechanism, the defect-rich HC-coated alloy structure (SnP₃@HC-γ) was integrated. Due to the high energy and strong penetrability of γ-rays, the constructed "self-doping" defect engineering effectively expands the interlayer structure of HC and forms the irregular ring structure. Simultaneously, the exposed large number of coordination unsaturated sites can accelerate the reaction kinetics on the surface. Based on the synergistic effect of the SnP₃@HC-γ, the composites exhibit an excellent reversible capacity of 668 mAh g^-1 at 0.1 A g^-1 in SIBs. Even, after 400 cycles at 1.0 A g^-1, an exceptional cyclability with 88% capacity retention (430 mAh g^-1) can be maintained. We envision that the γ-irradiation technology used in this research not only overturns the general perception that "self-doping" defects will reduce performance, but also provides reliable technical support for large-scale construction of high-defect, high-capacity and stable sodium-ion anode materials.

Carbon nitride/positive carbon black anchoring PtNPs assembled byγ-rays as ORR catalyst with excellent stability

Electrocatalytic performance of low-cost graphitic carbon nitride (CN) is greatly limited by its limited conductivity and small specific surface area. Herein, a simple and cost-effective idea to produce novel nanocomposite is constructed by the CN and cetyl trimethyl ammonium bromide functionalized carbon black (CB) anchored platinum nanoparticles as highly efficient oxygen reduction catalysts based on gamma irradiation. The assembled carbon nitride/positive carbon black anchoring PtNPs (Pt/CN₂-CB⁺₁) catalyst exhibits significantly improved specific surface area, high graphitization, and uniformly dispersed ultra-small platinum nanoparticles. For the oxygen reduction reaction (ORR) performance, the catalyst shows more positive onset-potential (0.93 V versus RHE) and larger diffusion limiting current density (5.65 mA cm^-2) compared with benchmark Pt/C catalysts in alkaline medium. Moreover, the Pt/CN₂-CB⁺₁catalyst exhibits a small Tafel slope (92 mV dec^-1). Besides, the catalyst was demonstrated the remarkable methanol tolerance and good long-term stability under working conditions. This work provides a new and effectiveγ-rays irradiation for synthesizing the carbon nitride catalysts for energy conversion and storage applications.

Cross-Linked Covalent Organic Framework-Based Membranes with Trimesoyl Chloride for Enhanced Desalination

The rational design of continuous covalent organic framework (COF)-based membranes is challenging for desalination applications, mainly due to the larger intrinsic pore size of COFs and defects in the crystalline film, which lead to a negligible NaCl rejection ratio. In this work, we first demonstrated a COF-based desalination membrane with in situ cross-linking of a COF-TpPa layer by trimesoyl chloride (TMC) to stitch the defects between COF crystals and cross-link the COF cavity with high-cross-linking degree networks to enhance NaCl rejection. With the addition of TMC monomers, both small spherical nodules and some elongated "leaf-like" features were observed on the membrane surface due to the appearance of nanovoids during cross-linking. The resulting COF-based desalination membrane had a water permeability of approximately 0.81 L m^-2 h^-1 bar^-1 and offered substantial enhancement of the NaCl rejection ratio from being negligible to 93.3% at 5 bar. Mechanistic analysis indicated that the amidation reaction of the secondary amine in keto COF with TMC induced the formation of a highly porous network structure both in the cavity and on the exterior of COF, thereby successfully forming a continuous and nanovoid-containing selective layer for desalination. In addition, the membrane exhibited excellent desalting performance for real industrial wastewater with both low and high salinity. This study proposed that the introduction of a cross-linker to react with the terminal amine group and secondary amine in the backbone of the keto form of COF or its derivatives could provide a facile and scalable approach to fabricate a COF-based membrane with superior NaCl rejection. This opens a new fabrication route for COF-based desalination membranes, as well as extended applications in water desalination.

Novel Positively Charged Metal-Coordinated Nanofiltration Membrane for Lithium Recovery

Nanofiltration (NF) with high water flux and precise separation performance with high Li⁺/Mg²⁺ selectivity is ideal for lithium brine recovery. However, conventional polyamide-based commercial NF membranes are ineffective in lithium recovery processes due to their undesired Li⁺/Mg²⁺ selectivity. In addition, they are constrained by the water permeance selectivity trade-off, which means that a highly permeable membrane often has lower selectivity. In this study, we developed a novel nonpolyamide NF membrane based on metal-coordinated structure, which exhibits simultaneously improved water permeance and Li⁺/Mg²⁺ selectivity. Specifically, the optimized Cu-m-phenylenediamine (MPD) membrane demonstrated a high water permeance of 16.2 ± 2.7 LMH/bar and a high Li⁺/Mg²⁺ selectivity of 8.0 ± 1.0, which surpassed the trade-off of permeance selectivity. Meanwhile, the existence of copper in the Cu-MPD membrane further enhanced anti-biofouling property and the metal-coordinated nanofiltration membrane possesses a pH-responsive property. Finally, a transport model based on the Nernst-Planck equations has been developed to fit the water flux and rejection of uncharged solutes to the experiments conducted. The model had a deviation below 2% for all experiments performed and suggested an average pore radius of 1.25 nm with a porosity of 21% for the Cu-MPD membrane. Overall, our study provides an exciting approach for fabricating a nonpolyamide high-performance nanofiltration membrane in the context of lithium recovery.

Differentiating Solutes with Precise Nanofiltration for Next Generation Environmental Separations: A Review

Selective removal or enrichment of targeted solutes including micropollutants, valuable elements, and mineral scalants from complex aqueous matrices is both challenging and pivotal to the success of water purification and resource recovery from unconventional water resources. Membrane separation with precision at the subnanometer or even subangstrom scale is of paramount importance to address those challenges via enabling "fit-for-purpose" water and wastewater treatment. So far, researchers have attempted to develop novel membrane materials with precise and tailored selectivity by tuning membrane structure and chemistry. In this critical review, we first present the environmental challenges and opportunities that necessitate improved solute-solute selectivity in membrane separation. We then discuss the mechanisms and desired membrane properties required for better membrane selectivity. On the basis of the most recent progress reported in the literature, we examine the key principles of material design and fabrication, which create membranes with enhanced and more targeted selectivity. We highlight the important roles of surface engineering, nanotechnology, and molecular-level design in improving membrane selectivity. Finally, we discuss the challenges and prospects of highly selective NF membranes for practical environmental applications, identifying knowledge gaps that will guide future research to promote environmental sustainability through more precise and tunable membrane separation.

Constructing dense and hydrophilic forward osmosis membrane by cross-linking reaction of graphene quantum dots with monomers for enhanced selectivity and stability

This paper reports a novel thin-film nanocomposite (TFN) membrane with a dense, flat, and hydrophilic polyamide (PA) layer. The atypical PA structure was obtained by the cross-linking reaction of graphene oxide quantum dots containing amino groups (NH₂-GOQDs) with triacyl chloride and polyamide oligomers. And the resulting TFN membrane showed a flat (small-scale ridge structure) and smooth surface. Meanwhile, the introduction of oxygen-containing and amino functional groups increased surface hydrophilicity. The reaction of amino groups on the NH₂-GOQDs with acid chloride groups and the carboxyl groups (in the linear part of the polyamide) enhanced the degree of cross-linking of the PA layer, forming a compact surface. Owning to the dense surface structure, excellent hydrophilicity, and small water transmission distance, the optimized TFN membrane exhibited an enhanced water flux of 26.57 L⋅m^-2⋅h^-1 with a low reverse salt flux of 6.0 g⋅m^-2⋅h^-1. Furthermore, nano-indentation/scratch results showed the interface adhesion between substrate and PA layer was improved due to the physical anchoring of NH₂-GOQDs in the substrate. And in the long-term FO test, the TFN membrane showed stable selectivity. This work proves that the targeted structural design of the PA layer at the nanoscale will have a positive impact on desalination field.