In-situ recovery of bio-butanol from glycerol fermentation using PDMS/ceramic composite membrane

Dielectric and Mechanical Properties of PDMS-La2Ba2XZn2Ti3O14 (X = Mg/Ca/Sr) Nanocomposites

Flexible polydimethylsiloxane-La2Ba2XZn2Ti3O14 (X = Mg/Ca/Sr) [PDMS-LBT] nanocomposites with high permittivity (dielectric constant, k) are prepared through a room-temperature mixing process. The LBT nanoparticles used in this study are prepared through a high-temperature solid-state reaction. It is observed that LBT (X = Mg/Ca) nanoparticles are spherical in nature, with particle size ∼20 nm, as observed from the HRTEM images, whereas LBT (X = Sr) nanoparticles are cubical in nature with particle size ≥100 nm. These LBT (X = Mg/Ca/Sr) nanoparticles are crystalline in nature, as apparent from the XRD analysis and SAED patterns. The permittivity of LBT nanoparticles is higher when "Ca" is present in place of "X". These three oxides show a temperature-dependent dielectric behavior, where LBT nanoparticles with "Sr" show a sharp change in permittivity at a temperature of ∼105 °C. These kinds of oxide materials, especially LBT (X = Sr) nanoparticles/oxides, can be used in dielectric/resistive switching devices. The effect of LBT nanoparticle concentration on the dielectric and mechanical properties of PDMS-LBT nanocomposites is widely studied and found that there is a significant increase in dielectric constant with an increase in the concentration of LBT nanoparticles. There is a decrease in the volume resistivity with the increase in the LBT nanoparticle concentration. All the PDMS-LBT nanocomposites have low dielectric loss (ε″) compared to the dielectric constant value. It is found that both permittivity (ε') and AC conductivity (σac) of PDMS-LBT composites are increased with the temperature at a frequency of 1 Hz. The % elongation at break (% EB) and tensile strength (TS) decrease with the LBT nanoparticle concentration in the matrix PDMS, which is due to the non-reinforcing behavior of LBT nanoparticles. The distribution and dispersion of LBT nanoparticles in the matrix PDMS are observed through HRTEM and AFM/SPM.

Methoxy terminated poly dimethylsiloxane bonded stationary phase for reversed-phase liquid chromatography

In this work, a methoxy terminated poly dimethylsiloxane modified silica gel material was proposed as a novel stationary phase for reversed-phase liquid chromatography. With 5 μm silica gel as matrix, methoxy terminated poly dimethylsiloxane polymer was grafted by one step chemical bonding reaction. The obtained stationary phase was characterized by scanning electron microscopy, fourier transform infrared spectroscopy and element analysis. To our knowledge, this is the novel methoxy terminated poly dimethylsiloxane bonded stationary phase with good separation efficiency (42107-46988 plates/m for benzene homologues) and high stability (RSD is 0.08-5.09%). Comparing to other traditional columns of the same type, the proposed stationary phase has a wider polarity separation scale and shorter analysis time. In addition to the rapid separation of hydrophobic compound, such column also exhibited great potential in the separation of hydrophilic analytes.

A review of recent developments on kinetics parameters for glycerol electrochemical conversion - A by-product of biodiesel

Glycerol is a by-product produced from biodiesel, fatty acid, soap and bioethanol industries. Today, the value of glycerol is decreasing in the global market due to glycerol surplus, which primarily resulted from the speedy expansion of biodiesel producers around the world. Numerous studies have proposed ways of managing and treating glycerol, as well as converting it into value-added compounds. The electrochemical conversion method is preferred for this transformation due to its simplicity and hence, it is discussed in detail. Additionally, the factors that could affect the process mechanisms and products distribution in the electrochemical process, including electrodes materials, pH of electrolyte, applied potential, current density, temperature and additives are also thoroughly explained. Value-added compounds that can be produced from the electrochemical conversion of glycerol include glyceraldehyde, dihydroxyacetone, glycolic acid, glyceric acid, lactic acid, 1,2-propanediol, 1,3-propanediol, tartronic acid and mesoxalic acid. These compounds are found to have broad applications in cosmetics, pharmaceutical, food and polymer industries are also described. This review will be devoted to a comprehensive overview of the current scenario in the glycerol electrochemical conversion, the factors affecting the mechanism pathways, reaction rates, product selectivity and yield. Possible outcomes obtained from the process and their benefits to the industries are discussed. The utilization of solid acid catalysts as additives for future studies is also suggested.