Alachlor dechlorination prior to an electro-Fenton process: Influence on the biodegradability of the treated solution

Integrating electro-Fenton and microalgae for the sustainable management of real food processing wastewater

The present study demonstrates, for the first time, the feasibility of a two-step process consisting of Electro-Fenton (EF) followed by microalgae to treat highly loaded real food processing wastewater along with resource recovery. In the first step, EF with a carbon felt cathode and Ti/RuO2-IrO2 anode was applied at different current densities (3.16 mA cm-2, 4.74 mA cm-2 and 6.32 mA cm-2) to decrease the amount of organic matter and turbidity and enhance biodegradability. In the second step, the EF effluents were submitted to microalgal treatment for 15 days using a mixed culture dominated by Scenedesmus sp., Chlorosarcinopsis sp., and Coelastrum sp. Results showed that current density impacted the amount of COD removed by EF, achieving the highest COD removal of 77.5% at 6.32 mA cm-2 with >95% and 74.3% of TSS and PO43- removal, respectively. With respect to microalgae, the highest COD removal of 85% was obtained by the culture in the EF effluent treated at 6.32 mA cm-2. Remarkably, not only 85% of the remaining organic matter was removed by microalgae, but also the totality of inorganic N and P compounds, as well as 65% of the Fe catalyst that was left after EF. The removal of inorganic species also demonstrates the high complementarity of both processes, since EF does not have the capacity to remove such compounds, while microalgae do not grow in the raw wastewater. Furthermore, a maximum of 0.8 g L-1 of biomass was produced after cultivation, with an accumulation of 32.2% of carbohydrates and 25.9% of lipids. The implementation of the two processes represents a promising sustainable approach for the management of industrial effluents, incorporating EF in a water and nutrient recycling system to produce biomass that could be valorized into clean fuels.

A new attempt to remove toluene using nickel-iron bimetallic particle electrode reactor

A new attempt of removing toluene waste gas using a three-dimensional electrode reaction device with nickel-iron bimetallic particle electrode is presented in this paper. The particle electrode was prepared by a simple liquid phase reduction method. Through bimetal modification, the particle electrode mass transfer rate is increased to 1.29 times, and the degradation efficiency of the reactor is increased by nearly 40%, which makes it possible to remove toluene waste gas by other electrochemical methods in addition to plasma method. The removal efficiency of the particle electrode can be stabilized at more than 80% after 5 cycles (50 h). At the same time, the relationship between independent working parameters and dependent variables is analyzed using the central composite design, and the operating parameters are optimized. Based on this study, the removal mechanism and possible degradation pathway of toluene were investigated. This study provides a supplement to the possibility and theoretical basis of new technology application for electrocatalytic oxidation removal of VOCs.

Removal of ofloxacin using a porous carbon microfiltration membrane based on in-situ generated •OH

This study investigated the removal performance of ofloxacin (OFL) by a novel electro-Fenton enhanced microfiltration membrane. The membranes used in this study consisted of metal-organic framework derived porous carbon, carbon nanotubes and Fe2+, which were able to produce hydroxyl radicals (•OH) in-situ via reducing O2 to hydrogen peroxide. Herein, membrane filtration with bias not only concentrated the pollutants to the level that could be efficiently treated by electro-Fenton but also confined/retained the toxic intermediates within the membrane to ensure a prolonged contact time with the oxidants. After validated by experiments, the applied bias of -1.0 V, pH of 3 and electrolyte concentration of 0.1 M were the relatively optimum conditions for OFL degradation. Under these conditions, the average OFL removal rate could be reach 75% with merely 5% membrane flux loss after 4 cycles operation by filtrating 1 mg/L OFL. Via decarboxylation reaction, piperazinyl ring opening, dealkylation and ipso substitution reaction, etc., OFL could be gradually and efficiently degraded to intermediate products and even to CO2 by •OH. Moreover, the oxidation reaction was preferred to following first-order reaction kinetics. This research verified a possibility for antibiotic removal by electro-enhanced microfiltration membrane.

Waste coconut shell-derived carbon monolith as an efficient binder-free cathode for electrochemical advanced oxidation treatment of endocrine-disrupting compounds

Discharge of endocrine-disrupting compounds such as methylparaben (MePa) into natural water bodies deteriorates the aquatic ecosystem. In this regard, electrochemical oxidation (EO) and electro-Fenton (EF) processes are acknowledged as effective methods to eliminate biorecalcitrant compounds from different wastewater matrices. In these systems, the H2O2-producing ability of carbon-based cathodes is put to advantage for producing homogenous hydroxyl radicals by simulating Fenton's reaction, which dramatically augments the contaminant removal efficiency. However, commercial carbon based cathodes are not economically affordable, especially for voluminous treatment. Hence in the present work, waste-derived carbonised coconut shell (CCS) monolith was employed as a cathode in EO and EF treatment of MePa. Almost the entire MePa with initial concentration of 10 mg/L was removed in 60 min by EO and 45 min by EF process at neutral pH, applied current density of 7.5 mA/cm2, NaCl concentration of 1.0 g/L and 10 mg/L of Fe2O3 dosing. The MePa removal efficiency of the CCS cathode-fitted system after 60 min was better than the commercial graphite plate and Ti-based mixed metal oxide employing system due to higher H2O2 electrosynthesis (H2O2 = 9.0 ± 0.6 mg/L after 60 min). Moreover, the same setup was used for treating 10 mg/L of MePa-spiked real sewage and demonstrated MePa and total organic carbon removal efficiency of 80.16 ± 2.31% and 37.42 ± 3.50%, respectively, in 45 min. Further, the CCS-mediated EF treatment achieved >90% removal of MePa for eight continuous batch cycles and recorded a current density drop of just 0.23% per cycle. The degradation pathway and toxicity assessment of the intermediates using the Ecological Structure Activity Relationships (ECOSAR) tool supported the eco-friendliness of the current treatment scheme.

Removal of Iodine-Containing X-ray Contrast Media from Environment: The Challenge of a Total Mineralization

Iodinated X-ray contrast media (ICM) as emerging micropollutants have attracted considerable attention in recent years due to their high detected concentration in water systems. It results in environmental issues partly due to the formation of toxic by-products during the disinfection process in water treatment. Consequently, various approaches have been investigated by researchers in order to achieve ICM total mineralization. This review discusses the different methods that have been used to degrade them, with special attention to the mineralization yield and to the nature of formed by-products. The problem of pollution by ICM is discussed in the first part dedicated to the presence of ICM in the environment and its consequences. In the second part, the processes for ICM treatment including biological treatment, advanced oxidation/reductive processes, and coupled processes are reviewed in detail. The main results and mechanisms involved in each approach are described, and by-products identified during the different treatments are listed. Moreover, based on their efficiency and their cost-effectiveness, the prospects and process developments of ICM treatment are discussed.

Insight into the Fe-Ni/biochar composite supported three-dimensional electro-Fenton removal of electronic industry wastewater

For the efficient removal of the bio-refractory organic pollutants in the electronic industry wastewater, the Ni-Fe (oxides) modified three-dimension (3D) particle electrode was applied in electro-Fenton system (3D/EF), where iron ions were released from anode and deposited onto algal biochar (ABC) to prepare composite catalyst during reaction process. Firstly, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) analysis were applied to confirm successful fabrication of the 3D particle electrode materials. Secondly, COD removal efficiency could reach about 80%, which was about 20% higher than that in 2D/EF system, under the optimized conditions as 2.0 g/L of Ni-ABC particle electrodes, initial pH of 3, 100 mL/min of aeration intensity and 20 mA/cm² of applied current density. Thirdly, characterized using three-dimensional fluorescence spectroscopy and GC-MS analysis, it seemed that most of the macromolecular substances could be degraded, whereas mono-2-ethylhexyl phthalate (MEHP) was identified as the most abundant and representative compound. Finally, possible degradation pathway of MEHP in 3D/EF system was proposed including dealkylation, cleavage of C-O bond, and demethylation. Therefore, this study provides a new strategy in designing EF system employing bimetal doped biochar composite for an efficient elimination of organic pollutants within electronic industry wastewater.

Removal of Chloroacetanilide Herbicides from Water Using Heterogeneous Photocatalysis with TiO2/UV-A

Chloroacetanilide herbicides are widely used in the agricultural sector throughout the world. Because of their poor biodegradability, high water solubility, and long persistence, chloroacetanilide herbicides have a high potential to contaminate water, and conventional water treatment processes do not ensure sufficient removal. Therefore, heterogeneous photocatalysis using TiO2/UV-A was investigated for the degradation of alachlor, acetochlor, and metolachlor from water. Two commercially available TiO2 (P25 and AV-01) were used as photocatalysts. Different experimental setups were also tested. In addition, the toxicity of single herbicides and mixtures of their photocatalytic degradation products to the freshwater alga Chlorella kessleri was investigated via a growth inhibition test. The maximum removal efficiency for alachlor, acetochlor, and metolachlor was 97.5%, 93.1%, and 98.2%, respectively. No significant differences in the removal efficiency of chloroacetanilide herbicides were observed for the photocatalysts used. Although the concentrations of all herbicides during photocatalysis decreased, the toxicity of the resulting mixtures of degradation products increased or remained the same, indicating the formation of toxic degradation products.

High activity of step sites on Pd nanocatalysts in electrocatalytic dechlorination

The role of step sites on nanocatalysts in the electrocatalytic dechlorination reaction (ECDR) was studied using 3 Pd nanocatalysts with different densities of step sites, which decreased in the order of: tetrahexahedral Pd{310} nanocrystals (THH Pd{310} NCs) > commercial Pd nanoparticles (Pd black) > cubic Pd{100} NCs. The two well-defined Pd NCs served as model catalysts and were prepared through the electrochemical square-wave potential (SWP) method. The toxic herbicide alachlor was first employed in this study as an objective probe to determine the dechlorination performance, which was quantified by the alachlor removal (R_ala), the current efficiency (CE_ala), and the dechlorination selectivity (S_des). The experimental results demonstrated that the THH Pd{310} NCs with abundant step sites exhibited much higher electrocatalytic performance compared to the cubic Pd{100} NCs with terrace sites. The combination of cyclic voltammetry studies, electrochemical in situ FTIR analysis, and density functional theory (DFT) calculations revealed that the adsorbed CO bond and generated on the step sites could lower the C-Cl bond splitting barrier, leading to a high ECDR efficiency. Other chlorinated organics with an activated carbon atom were also investigated, which revealed that the superiority of the step sites toward Cl-C bond breaking was particular to the compounds with CO bonds. This study provides a deep understanding of high actvitiy of step sites on Pd NCs in EHDC and a strategy to improve this important environmental electrocatalysis process.

Vacuum UV pre-treatment coupled with self-generated peroxide stimulation of biomass: An innovative hybrid system for detoxification and mineralization of toxic compounds

The degradation of p-nitrophenol (pNP) was investigated in the chemical-less UVC/VUV process (Advanced Oxidation/Reduction Process, AORP), the packed bed bioreactor (PBR), and the hybrid of AORP/PBR system. The control UVC/VUV process degraded and mineralized pNP with rate constants of 0.098 and 0.032 min^-1, respectively, at neutral initial pH. Operating the UVC/VUV process in a fluidized bed reactor improved the rate of pNP degradation by 21 % at a packing ratio of 0.5 %. The fluidized bed AORP was operated under continuous-flow mode, where 79 % degradation and 28 % mineralization of pNP were obtained along a significant improvement in the biodegradability (41 %) at a hydraulic retention time of 20 min. The oxidation with HO and reduction with e_aq^- simultaneously contributed to the degradation of pNP in the UVC/VUV process. In comparison, degradation and mineralization of pNP in a single PBR process (without pretreatment) was found to be 84.7 % and 47.2 %, respectively, during 30 h biotreatment. Coupling the fluidized bed UVC/VUV with the PBR attained complete biodegradation of the residual pNP within 1 h and over 89 % of TOC reduction during 3 h post treatment in the PBR. Accordingly, the hybrid, fluidized bed UVC/VUV reactor coupled with the PBR is an efficient and promising technology for treating toxic environmental contaminants.

Sensitive Determination of Acetochlor, Alachlor, Metolachlor and Fenthion Utilizing Mechanical Shaking Assisted Dispersive Liquid-Liquid Microextraction Prior to Gas Chromatography-Mass Spectrometry

A green, sensitive and accurate dispersive liquid-liquid microextraction (DLLME) method was used to preconcentrate four selected pesticides in dam lake water samples for determination by gas chromatography-mass spectrometry (GC-MS). Conditions of the DLLME method were comprehensively investigated and optimized according to type/volume of extraction solvent, type/volume of dispersive solvent, and type/period of mixing. The developed method was validated according to the limits of detection and quantitation, accuracy, precision and linearity. Under the optimum conditions, limit of detection values calculated for alachlor, acetochlor, metolachlor and fenthion were 1.7, 1.7, 0.2 and 7.8 µg/kg (mass based), respectively. The method recorded 202, 104, 275 and 165 folds improvement in detection power values for acetochlor, alachlor, metolachlor and fenthion, respectively, when compared with direct GC-MS measurements. In order to evaluate the accuracy of the developed method, real sample application with spiking experiments was performed on dam lake water samples, and satisfactory percent recovery results in the range of 81%-120% were obtained.

Electrochemical Processes Coupled to a Biological Treatment for the Removal of Iodinated X-ray Contrast Media Compounds

Iodinated X-ray contrast media (ICM) compounds are a form of intravenous radiocontrast containing iodine, which are rapidly eliminated via urine or feces. The issue with the accumulation of ICM has received considerable critical attention since they are ubiquitously distributed in municipal wastewater effluents and in the aquatic environment and are not significantly eliminated by most biological sewage treatment processes. Among the methods that have been tested to eliminate ICM, electrochemical methods have significant advantages, since they can selectively cut the carbon-iodine bonds that are suspected to decrease their biodegradability. On the production sites, the recovery of iodine ions due to the carbon-iodine cleavage can be envisaged, which is particularly interesting to reduce the cost of the ICM production process. The coupling of an electrochemical process and a biological treatment can be carried out to mineralize the organic part of the formed by-products, allowing the recovery of the iodide ions. Therefore, the degradation of diatrizoate, a typical ionic ICM compound, by an electrochemical process was the purpose of this study. The electrochemical reduction of diatrizoate was performed using a flow cell with a graphite felt electrode at different potentials. The removal yield of diatrizoate reached ~100% in 2 h and the main product, 3,5-diacetamidobenzoic acid, was quantitatively formed, showing that diatrizoate was almost completely deiodinated. According to the BOD₅/COD ratio, the biodegradability of diatrizoate after electrolysis was considerably improved. Cyclic voltammetry analysis of the electroreduced solution showed several oxidation peaks. The electrochemical oxidation of the by-products formed after the first treatment by electroreduction was then performed at three different potentials to study the influence of electrochemical oxidation on biodegradability. Results showed that the degradation yield of the deiodinated by-products increased with the potential and reached 100% at 1.3 V/SCE. Four different biological treatments were implemented during 21 days in stirred flasks with fresh activated sludge. The evolution of the mineralization during the biological treatment highlighted the biorecalcitrance of diatrizoate as previously estimated by the BOD₅/COD ratio. Interestingly, the mineralization yield increased from 41 to 60% when electrochemical oxidation at 1.3 V/SCE was implemented after electroreduction.

Efficient Dechlorination of α-Halocarbonyl and α-Haloallyl Pollutants by Electroreduction on Bismuth

The electrocatalytic activity of bismuth considered as a low-cost and green electrode material was studied in reductive dechlorination processes. Cyclic voltammetry analyses showed that the Bi electrode exhibited a high catalytic activity to reduce alachlor, a chlorinated herbicide, in the aqueous medium at different pH values. Bulk electrolyses were performed at different potentials and pH values. Alachlor was reduced in deschloroalachlor, its dechlorinated derivative, with a high selectivity (96%) and a current efficiency of 48%. The reductive dechlorination of other chlorinated compounds with an activated carbon atom was then studied, showing that the bismuth electrode catalyzed the electroreduction of chloroacetamides, α-halocarbonyl, and α-haloallyl pollutants. Cyclic voltammetry experiments allowed us to propose a mechanism explaining the high catalytic activity of bismuth to reduce these families of compounds.