Magnet-assisted selective oil removal from water in non-open channel and continuous oil spills clean-up

Inside-out templating: A strategy to decorate helical carbon nanotubes and 2D MoS2 on ethyl cellulose sponge for enhanced oil adsorption and oil/water separation

Ethyl cellulose (EC)-based composite sponges were developed for oil spillage treatment. The EC sponge surface was decorated with helical carbon nanotubes (HCNTs) and molybdenum disulfide (MoS2) (1 phr) using the inside-out sugar templating method. The inside surface of a sugar cube was coated with HCNTs and MoS2. After filling the sugar cube pores with EC and the subsequent sugar leaching, the decorating materials presented on the sponge surface. The EC/HCNT/MoS2 sponge had a high level of oil removal based on its adsorption capacity (41.68 g/g), cycled adsorption (∼75-79 %), separation flux efficiency (∼85-95 %), and efficiency in oil/water emulsion separation (92-94 %). The sponge maintained adsorption capacity in acidic, basic, and salty conditions, adsorbed oil under water, and functioned as an oil/water separator in a continuous pump-assisted system. The compressive stress and Young's modulus of the EC sponge increased following its decoration using HCNTs and MoS2. The composite sponge was robust based on cycled compression and was thermally stable up to ∼120 οC. Based on the eco-friendliness of EC, the low loading of HCNTs and MoS2, and sponge versatility, the developed EC/HCNT/MoS2 sponge should be good candidate for use in sustainable oil adsorption and separation applications.

Droplet impacting on pillared hydrophobic surfaces with different solid fractions

HYPOTHESIS

The solid fraction of the substrate is expected to influence the bouncing behavior of an impinging droplet, thereby affecting spreading and contact time. Hence, it should be possible to alter the velocity and pressure distribution of impacting droplet, and also affect the impact velocity for droplet penetration right upon impact.

SIMULATIONS

We systematically investigate the impact dynamics of water droplets on pillared hydrophobic surfaces with different solid fractions using phase-field simulations. The velocity and pressure distributions of impacting droplets on pillared hydrophobic surfaces with varied Weber numbers and solid fractions are studied. In addition, the influences of the solid fraction on the bouncing behaviors of the impinging droplet, such as the maximum wetting spreading, the maximum impacting depth, and the contact time, are also investigated to further understand the impact event.

FINDINGS

We show that a three-peak pressure profile appears on the top of the pillared hydrophobic surface during droplet impact by varying the solid fraction of the surface. The first peak is generated by the impact of the droplet itself, while the second peak arises from the droplet recoil impact associated with the dynamic properties of the jet. Moreover, we identify a hitherto unknown third pressure peak related to the hydrodynamic singularity that emerges due to the convergence of the fluid during the droplet rebound. This solid fraction-dependent impacting behavior reveals the intricate interplay between droplet dynamics and the underlying surface characteristics, providing valuable insights into the design and optimization of micro/nano structured hydrophobic surfaces for various applications.

Light-Propelled Super-Hydrophobic Sponge Motor and its Application in Oil-Water Separation

Self-propelled separation materials, that is, motor, are one of the keys to realizing smart oil-water separation. Although three-dimensional sponges such as commercial melamine sponge (MS) exhibit excellent oil-water separation ability, they cannot move by themselves on water. Aiming at solving this problem, a polydimethylsiloxane (PDMS) and molybdenum disulfide (MoS2) modified MS motor (PDMS@MS/MoS2) with an asymmetric multilayer structure was prepared, in which the photothermal layer MoS2 provided the propelling force for the motor under infrared light irradiation, and the middle layer PDMS was used as the superhydrophobic modified agent and adhesive agent between commercial MS and MoS2 powder. PDMS coated MS (PDMS@MS) as the superhydrophobic layer showed good superhydrophobic ability (153.1°) and oil-water separation capacity (52.33 g/g to liquid paraffin). Furthermore, the introduction of MoS2 made the speed of the sponge motor reach 8.27 mm s-1 with a removal quantity of 12.20 g/g for cyclohexane. After recycling 8 times, the contact angle, cyclohexane capturing amount, and average velocity of the motor were 150.3°, 11.40 g/g, and 8.41 mm/s, respectively. Meanwhile, PDMS@MS/MoS2 kept a similar light-propelling velocity (∼8 mm) at different pH values and in simulated seawater, demonstrating that the light-propelling motor possessed a good cycle and practical performance, which provides a possibility for the directional light propulsion of a sponge motor in oil-water separation.

A solvent-template ethyl cellulose-polydimethylsiloxane crosslinking sponge for rapid and efficient oil adsorption

Lipophilic adsorbents for oil-water separation are usually synthesized using the template method, in which hydrophobic materials are coated on a ready-made sponge. Herein, a novel solvent-template technique is used to directly synthesize a hydrophobic sponge, by crosslinking polydimethylsiloxane (PDMS) with ethyl cellulose (EC) which plays a vital role in the formation of 3D porous structure. The as-prepared sponge has advantages of strong hydrophobility, high elasticity, as well as excellent adsorption performance. In addition, the sponge can be readily decorated by nano-coatings. After the sponge was simply dipped in nanosilica, the water contact angle increases from 139.2° to 144.5°, and the maximum adsorption capacity for chiroform rises from 25.6 g/g to 35.4 g/g. The adsorption equilibrium can be reached within 3 min, and, the sponge can be regenerated by squeezing, without any change in hydrophobility or evident decline in capacity. The simulation tests of emulsion separation and oil-spill cleanup demonstrate that the sponge has great potential in oil-water separation.

Superhydrophobic magnetic sorbent via surface modification of banded iron formation for oily water treatment

In the current study, a simple dry coating method was utilized to fabricate a super-hydrophobic super-magnetic powder (ZS@BIF) for oily water purification using zinc stearate (ZS) and banded iron formation (BIF). The produced composite was fully characterized as a magnetic sorbent for oily water treatment. The results of X-ray diffraction diffractometer (XRD), Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS) and particle size analysis revealed the fabrication of homogenous hydrophobic-magnetic composite particles with core–shell structure. Contact angle and magnetic susceptibility results showed that 4 (BIF): 1 (Zs) was the ideal coverage ratio to render the core material superhydrophobic and preserve its ferromagnetic nature. The capability of the fabricated composite to sorb. n-butyl acetate, kerosene, and cyclohexane from oil–water system was evaluated. ZS@BIF composite showed a higher affinity to adsorb cyclohexane than n-butyl acetate and kerosene with a maximum adsorption capacity of about 22 g g⁻¹ and 99.9% removal efficiency. Moreover, about 95% of the adsorbed oils could be successfully recovered (desorbed) by rotary evaporator and the regenerated ZS@BIF composite showed high recyclability over ten repeated cycles.

Robust and durable liquid-repellent surfaces

This review provides a comprehensive summary of characterization, design, fabrication, and application of robust and durable liquid-repellent surfaces.