Advancement in optimization tactic achieved by newly developed chromatographic response function: Application to LC separation of raloxifene and its impurities

A New UPLC Method with Chemometric Design-Optimization Approach for the Simultaneous Quantitation of Brimonidine Tartrate and Timolol Maleate in an Eye Drop Preparation

A new ultra-performance liquid chromatography (UPLC) with photodiode array was proposed for the quantitation of Brimonidine Tartrate (BRI) and Timolol Maleate (TIM) in eye drop using experimental design and optimization methodology. A 3³ full factorial design was applied to uncover the effects of the selected factors and their interactions on the chromatographic response function for the optimization of experimental conditions in the development of a new UPLC method. As a result, the optimal chromatographic conditions giving a better separation and short analysis time were found to be 49.2°C for column temperature; 0.38 mL/min for flow rate and 56.7 % (v/v) for 0.1 M CH₃COOH used in mobile phase. The elution of BRI and TIM was reported as 0.508 and 0.652 min within a short runtime of 1.5 min, respectively. Calibration graphs for BRI and TIM were obtained by the regression of the concentration on the peak area, which was detected at 246 and 298 nm, respectively. The method validation was performed by the analysis of the synthetic mixtures, intra-day and inter-day samples and standard addition samples. This study shows that the optimized and validated UPLC method is very promising and available for the quantification of BRI and TIM in an eye drop formulation.

Development of alternative methods for the determination of raloxifene hydrochloride in tablet dosage form

<p>Three methods are proposed for the quantitative determination of raloxifene hydrochloride in pharmaceutical dosage form: ultraviolet method (UV) high performance liquid chromatography (HPLC) and micellar capillary electrophoresis (MEKC). These methods were developed and validated and showed good linearity, precision and accuracy. Also they demonstrated to be specific and robust. The HPLC and MEKC methods were tested in regards to be stability indicating methods and they showed to have this attribute. The UV method used methanol as solvent and optimal wavelength at 284 nm, obeying Lambert-Beer law in these conditions. The chromatographic conditions for the HPLC method included: NST column C18 (250 x 4.6 mm x 5 µm), mobile phase water:acetonitrile:triethylamine (67:33:0,3 v/v), pH 3.5, flow rate 1.0 mL min^-1, injection volume 20.0 µl, UV detection 287 nm and analysis temperature 30 °C. The MEKC method was performed on a fused-silica capillary (40 cm effective length x 50 µm i.d.) using as background electrolyte 35.0 mmol L^-1 borate buffer and 50.0 mmol L^-1 anionic detergent sodium dodecyl sulfate (SDS) at pH 8.8. The capillary temperature was 32°C, applied voltage 25 kV, UV detection at 280 nm and injection was perfomed at 45 mBar for 4 s, hydrodimanic mode. In this MEKC method, potassium diclofenac (200.0 µg mL^-1) was used as internal standard. All these methods were statistically analyzed and demonstrated to be equivalent for quantitative analysis of RLX in tablets and were successfully applied for the determination of the drug.</p>

Systematical approach in evaluation of LC method for determination of raloxifene hydrochloride and its impurities employing experimental design

Method validation presents a detailed investigation of analytical method and provision of the evidence that the method, when correctly applied, produces results that fit to the purpose. In order to achieve the method validation scope efficiently, experimental design presents a very useful tool. The greatest benefits of such approach could be seen in robustness testing through the provision of very useful data about the control of the chromatographic system during the routine application. In this paper, robustness testing of the LC method proposed for the determination of raloxifene hydrochloride and its four impurities was done employing Plackett-Burman design. Applying this design, the effect of five real factors (acetonitrile content, sodium dodecyl sulfate content, column temperature, pH of the mobile phase and flow rate) on the corresponding resolution factors was investigated through twelve experiments. Furthermore, the insignificance intervals for significant factors were calculated and the parameters for system suitability tests were defined. Eventually, the other validation parameters were tested and the effectiveness of the proposed analytical method with a high degree of accuracy was confirmed.