Development and characterization of microbial biosensors for evaluating low biochemical oxygen demand in rivers

Targeted Formation of Biofilms on the Surface of Graphite Electrodes as an Effective Approach to the Development of Biosensors for Early Warning Systems

Biofilms based on bacteria Pseudomonas veronii (Ps. veronii) and Escherichia coli (E. coli) and yeast Saccharomyces cerevisiae (S. cerevisiae) were used for novel biosensor creation for rapid biochemical oxygen demand (BOD) monitoring. Based on the electrochemical measurement results, it was shown that the endogenous mediator in the matrix of E. coli and Ps. veronii biofilms and ferrocene form a two-mediator system that improves electron transport in the system. Biofilms based on Ps. veronii and E. coli had a high biotechnological potential for BOD assessment; bioreceptors based on such biofilms had high sensitivity (the lower limits of detectable BOD5 concentrations were 0.61 (Ps. veronii) and 0.87 (E. coli) mg/dm3) and high efficiency of analysis (a measurement time 5-10 min). The maximum biosensor response based on bacterial biofilms has been observed in the pH range of 6.6-7.2. The greatest protective effect was found for biofilms based on E. coli, which has high long-term stability (151 days for Ps. veronii and 163 days for E. coli). The results of the BOD5 analysis of water samples obtained using the developed biosensors had a high correlation with the results of the standard 5-day method (R2 = 0.9820, number of tested samples is 10 for Ps. veronii, and R2 = 0.9862, number of tested samples is 10 for E. coli). Thus, biosensors based on Ps. veronii biofilms and E. coli biofilms could be a novel analytical system to give early warnings of pollution.

Microbial Biosensors for Rapid Determination of Biochemical Oxygen Demand: Approaches, Tendencies and Development Prospects

One of the main indices of the quality of water is the biochemical oxygen demand (BOD). A little over 40 years have passed since the practical application of the first microbial sensor for the determination of BOD, presented by the Japanese professor Isao Karube. This time span has brought new knowledge to and practical developments in the use of a wide range of microbial cells based on BOD biosensors. At present, this field of biotechnology is becoming an independent discipline. The traditional BOD analysis (BOD₅) has not changed over many years; it takes no less than 5 days to carry out. Microbial biosensors can be used as an alternative technique for assessing the BOD attract attention because they can reduce hundredfold the time required to measure it. The review examines the experience of the creation and practical application of BOD biosensors accumulated by the international community. Special attention is paid to the use of multiple cell immobilization methods, signal registration techniques, mediators and cell consortia contained in the bioreceptor. We consider the use of nanomaterials in the modification of analytical devices developed for BOD evaluation and discuss the prospects of developing new practically important biosensor models.

Microbial Fuel Cell-Based Biological Oxygen Demand Sensors for Monitoring Wastewater: State-of-the-Art and Practical Applications

Environmental pollution has been a continuous threat to sustainable development and global well-being. It has become a significant concern worldwide to combat the ecological crisis using low-cost innovative technologies. Biological oxygen demand (BOD) is a key indicator to comprehend the quality of water to guarantee environmental safety and human health; however, none of the present technologies are capable of online monitoring of the water at the source. Microbial fuel cells (MFC) are a promising technology for simultaneous power generation and wastewater treatment. MFCs have also been shown in fascinating applications to measure and detect the toxic pollutants present in wastewater. These are the bioreactors where exoelectrogenic microorganisms catalyze the conversion of the inherent chemical energy stored in organic compounds to electrical energy. Sensors employ energy conversion to measure BOD, which is considered an international index for the detection of organic material load present in wastewater. The MFC-based BOD sensors have gone through a wide range of advancement from mediator to mediator-less, double chamber to single-chamber, and large size to miniature. There have been detailed studies to improve the accuracy and reproducibility of the sensors for commercial applications. Additionally, multistage MFC-based BOD biosensors and miniature MFC-BOD sensors have also been ubiquitous in recent years. A considerable amount of work has been carried out to improve the performance of these devices by fabricating the proton exchange membranes and altering catalysts at the cathode. However, there remains a dearth for the fabrication of the devices in aspects like suitable microbes, proton exchange membranes, and cheaper catalysts for cathodes for effective real-time monitoring of wastewater. In this review, an extensive study has been carried out on various MFC-based BOD sensors. The efficiency and drawbacks associated with the different MFC-based BOD sensors have been critically evaluated, and future perspectives for their development have been investigated. The breadth of work compiled in this review will accelerate further research in MFC-based BOD biosensors. It will be of great importance to broad ranges of scientific research and industry.

Simultaneous measurement of the BOD concentration and temperature based on a tapered microfiber for water pollution monitoring

An optical sensor that simultaneously measures the concentration of the biochemical oxygen demand (BOD) and temperature in water based on a tapered microfiber is proposed for environmental monitoring. The sensor is characterized by a strong evanescent field, which is more sensitive to liquids with a low refractive index and a low transmission loss. The results show that as the BOD concentration increases, the interference spectrum shifts toward longer wavelengths, the spectral loss decreases, and the sensitivities of the BOD are 12.17 nm/mg/mL and -2.387dB/mg/mL in the range of 0.25-1 mg/mL, which indicates the extent of the water pollution. The detection limit for the BOD concentration is as low as 0.0016 mg/mL. As the ambient temperature increases, the interference spectrum shifts toward shorter wavelengths, the spectral loss decreases, and the temperature sensitivities are -0.339nm/^∘C and -0.031dB/^∘C in the range of 30°C-60°C. The matrix method can be used to achieve the simultaneous measurement of the BOD concentration and environmental temperature because the spectral interference peaks have different responses to these two parameters. The sensor can not only be used for detecting water pollution in rivers, drinking water, and groundwater but can also be utilized for other types of environmental monitoring. This sensor has great potential to act as a basic sensing unit in fiber-optic sensor networks for multiparameter measurements and intelligent monitoring.

Current status of water environment and their microbial biosensor techniques - Part II: Recent trends in microbial biosensor development

In Part I of the present review series, I presented the current state of the water environment by focusing on Japanese cases and discussed the need to further develop microbial biosensor technologies for the actual water environment. I comprehensively present trends after approximately 2010 in microbial biosensor development for the water environment. In the first section, after briefly summarizing historical studies, recent studies on microbial biosensor principles are introduced. In the second section, recent application studies for the water environment are also introduced. Finally, I conclude the present review series by describing the need to further develop microbial biosensor technologies. Graphical abstract Current water pollution indirectly occurs by anthropogenic eutrophication (Part I). Recent trends in microbial biosensor development for water environment are described in part II of the present review series.