Electrocatalytic oxidation of nitrite using metal-free nitrogen-doped reduced graphene oxide nanosheets for sensitive detection

Fast preparing bioelectrode with conductive bioink for nitrite detection in high sensitivity and stability

Electrochemically active biofilms (EABs) for nitrite detection have high specificity, rapid response, operational simplicity, and extended lifespan advantages. However, their scale production remains challenging due to time-consuming and uniform preparation. In this study, a novel approach was proposed to fast fabricate an EAB biosensor with a synthetic biofilm electrode for nitrite detection. The biofilm electrode was prepared by coating bioinks with varying conductive materials onto the surface of the graphite sheets, showing short incubation time and good reproducibility. Incorporating conductive materials into the bioinks remarkably enhanced the maximum voltage of the first cycle of bioelectrode incubation, with an increase of up to 633% for carbon nanofibers. The nitrite reduction current was amplified by a factor of 2.97, due to the enhancement of extracellular electron transfer (EET). The developed nitrite biosensor exhibited a detection range of 0.1-15 mg NO2--N L-1, with a high sensitivity of 610.8 μA mM-1 cm-2, and a stabilization operation time of at least 280 cycles. This study not only provided valuable insights into conductive materials for synthetic biofilms but also presented a practical approach for the rapid preparation, scale production, and optimization of highly sensitive and stable EAB sensors.

Catalytic ozonation for imazapic degradation over kelp-derived biochar: Promotional role of N- and S-based active sites

It is a feasible strategy to prepare reliable biochar catalysts for heterogeneous catalytic ozonation (HCO) processes by using inexpensive, high quality, and easily available raw materials. Here, an environmentally friendly, simple, and green biochar catalyst rich in nitrogen (N) and sulfur (S) has been prepared by the pyrolysis of kelp. Compared with directly carbonized kelp biomass (KB), acid-activated KB (KBA) and base-activated KB (KBB) have higher specific surface areas and more extensive porous structures, although only KBB displays effective ozone activation. Imazapic (IMZC), a refractory organic herbicide, was chosen as the target pollutant, which has apparently not hitherto been investigated in the HCO process. Second-order rate constants (k) for the reactions of IMZC with three different reactive oxygen species (ROS), specifically kO3, IMZC, kOH, IMZC, and k1O2, IMZC, have been determined as 0.974, 2.48 × 109, and 6.23 × 105 M-1 s-1, respectively. The amounts of graphitic N and thiophene S derived from the intrinsic N and S showed good correlations with the IMZC degradation rate, implicating them as the main active sites. OH and O2- and 1O2 were identified as main ROS in heterogeneous catalytic ozonation system for IMZC degradation. This study exemplified the utilization of endogenous N and S in biological carbon, and provided more options for the application of advanced oxidation processes and the development of marine resources.

Facile Controlled Synthesis of Pd-ZnO Nanostructures for Nitrite Detection

The electrocatalytic characteristics of nanostructures are significantly affected by surface structure. The strict regulation of structural characteristics is highly beneficial for the creation of novel nanocatalysts with enhanced electrocatalytic performance. This work reports a nitrite electrochemical sensor based on novel flower-like Pd-ZnO nanostructures. The Pd-ZnO nanocatalysts were synthesized through a simple hydrothermal method, and their morphology and structure were characterized via field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). Their electrocatalytical performance in the nitrite oxidation reaction was studied via cyclic voltammetry (CV) and the amperometric technique. Compared to pure ZnO and Pd nanoparticles, the Pd-ZnO nanostructures exhibited enhanced electrochemical performance in the nitrite oxidation reaction. In order to investigate the relationships between the structures of Pd-ZnO nanocatalysts and the corresponding electrocatalytic performances, different surface morphologies of Pd-ZnO nanocatalysts were fabricated by altering the solution pH. It was found that the flower-like Pd-ZnO nanostructures possessed larger effective surface areas and faster electron transfer rates, resulting in the highest electrocatalytic performance in the nitrite oxidation reaction. The designed nitrite sensor based on flower-like Pd-ZnO displayed a wide concentration linear range of 1 μM-2350 μM, a low detection limit of 0.2 μM (S/N of 3), and high sensitivity of 151.9 μA mM^-1 cm^-2. Furthermore, the proposed sensor exhibited perfect selectivity, excellent reproducibility, and long-time stability, as well as good performance in real sample detection.

Gold Nanoclusters Dispersed on Gold Dendrite-Based Carbon Fibre Microelectrodes for the Sensitive Detection of Nitric Oxide in Human Serum

Herein, gold nanoclusters (Au NC) dispersed on gold dendrite (Au DS)-based flexible carbon fibre (AuNC@AuDS|CF) microelectrodes are developed using a one-step electrochemical approach. The as-fabricated AuNC@AuDS|CF microelectrodes work as the prospective electrode materials for the sensitive detection of nitric oxide (NO) in a 0.1 M phosphate buffer (PB) solution. Carbon microfibre acts as an efficient matrix for the direct growth of AuNC@AuDS without any binder/extra reductant. The AuNC@AuDS|CF microelectrodes exhibit outstanding electrocatalytic activity towards NO oxidation, which is ascribed to their large electrochemical active surface area (ECSA), high electrical conductivity, and high dispersion of Au nanoclusters. As a result, the AuNC@AuDS|CF microelectrodes attain a rapid response time (3 s), a low limit of detection (LOD) (0.11 nM), high sensitivity (66.32 µA µM cm^-2), a wide linear range (2 nM-7.7 µM), long-term stability, good reproducibility, and a strong anti-interference capability. Moreover, the present microsensor successfully tested for the discriminating detection of NO in real human serum samples, revealing its potential practicability.

Insight into the roles of endogenous minerals in the activation of persulfate by graphitized biochar for tetracycline removal

Owing to its environmental-friendliness, low-cost, and outstanding characteristics, biochar has been widely used for the catalytic degradation of various organic pollutants. In this study, a pre- and post-deashing graphitized biochar (DBC800 and PBC800-A) was prepared and compared with the pristine biochar (PBC800) to activate persulfate (PS) for tetracycline (TC) degradation. The influence of the natural endogenous mineral on the catalytic ability of biochar was investigated. Characterization results show that the inherent endogenous mineral in biochar not only acted as a natural pore-forming agent to promote the formation of the porous structure, but also facilitated the formation of edge defective structures, and altered the surface functional groups, as well as increased the carbonization and graphitization degree of biochar. The PBC800-A exhibited a much higher catalytic efficiency on PS activation and TC oxidative degradation with the reaction rate of 0.06055 min^-1, 7.14 times as that of DBC800 (0.00861 min^-1) and 4.63 times as that of PBC800 (0.00158 min^-1). The endogenous minerals were conducive to the generation of free radicals and promoted the oxidative degradation of TC, which was mainly attributed to the improved carbon configuration. The post-deashing treatment was also found to significantly improve the electron transport efficiency of biochar by removing the residual ash, thereby promoting the generation of singlet oxygen. This study demonstrated that the natural minerals in biochar was beneficial for the degradation of TC, and more alternative natural minerals can be applied to co-pyrolysis with biochar for the remediation of refractory organic pollutants.

Application of Graphene-Based Materials for Detection of Nitrate and Nitrite in Water-A Review

Nitrite and nitrate are widely found in various water environments but the potential toxicity of nitrite and nitrate poses a great threat to human health. Recently, many methods have been developed to detect nitrate and nitrite in water. One of them is to use graphene-based materials. Graphene is a two-dimensional carbon nano-material with sp² hybrid orbital, which has a large surface area and excellent conductivity and electron transfer ability. It is widely used for modifying electrodes for electrochemical sensors. Graphene based electrochemical sensors have the advantages of being low cost, effective and efficient for nitrite and nitrate detection. This paper reviews the application of graphene-based nanomaterials for electrochemical detection of nitrate and nitrite in water. The properties and advantages of the electrodes were modified by graphene, graphene oxide and reduced graphene oxide nanocomposite in the development of nitrite sensors are discussed in detail. Based on the review, the paper summarizes the working conditions and performance of different sensors, including working potential, pH, detection range, detection limit, sensitivity, reproducibility, repeatability and long-term stability. Furthermore, the challenges and suggestions for future research on the application of graphene-based nanocomposite electrochemical sensors for nitrite detection are also highlighted.

Converting the Conducting Behavior of Graphene Oxides from n-Type to p-Type via Electron-Beam Irradiation

We studied the effects of electron-beam irradiation (EBI) on the structural and gas-sensing properties of graphene oxide (GO). To understand the effects of EBI on the structure and gas-sensing behavior of irradiated GO, the treated GO was compared with nonirradiated GO. Characterization results indicated an enhancement in the number of oxygen functional groups that occurs with EBI exposure at 100 kGy and then decreases with doses in the range of 100-500 kGy. Data from Raman spectra indicated that EBI could generate defects, and NO₂-sensing results at room temperature showed a decreased NO₂ response after exposure to EBI at 100 kGy; further increasing the dose to 500 kGy resulted in p-type semiconducting conductivity. The conversion of GO from n-type to p-type via EBI is explained not only through the generation of holes but also the variation in the amount of residual functional groups, including carboxyl (COOH) and hydroxyl groups (C-OH). The obtained results suggest that EBI can be a useful tool to convert GO into a diverse range of sensing devices.

Rutin detection using highly electrochemical sensing amplified by an Au–Ag nanoring decorated N-doped graphene nanosheet

The novel Au–Ag nanorings/NG modified electrode was found to have a wide linear range from 0.05 μM to 241.2 μM (S/N = 3) with a low detection limit of 0.01 μM when it was employed for rutin detection.