Electrospun nanofibers and spin coated films prepared from side-chain copolymers with chemically bounded platinum (II) porphyrin moieties for oxygen sensing and pressure sensitive paints

A novel optical dual sensor based on a coaxial electrospinning method for simultaneous sensing of oxygen and ammonia

The coaxial electrospinning method is widely used in a wide range of applications, including medical devices and sensing technology. This study proposes a novel optical dual sensor for simultaneous detection of oxygen (O2) and ammonia (NH3) based on coaxial electrospinning method to produce core-shell fiber membrane doped fluorescent dyes. The O2 (core) and NH3 (shell) sensitive dye membranes were successfully fabricated using coaxial electrospinning method by dissolving a polymer matrix, cellulose acetate (CA), with platinum (II) meso-tetrakis (pentafluorophenyl) porphyrin (PtTFPP) and Eosin-Y, respectively. The optical dual sensor was illuminated by an UV LED to monitor the intensity change and wavelength shift in the presence of selected analyte gases. The experimental data show that the sensitivities of optical dual sensor were found to be 6.4 and 3.2 for O2 and NH3, respectively. The response and recovery times of O2 and NH3 sensing probes were measured to be 12 s/29 s and 65 s/66 s, respectively. Also, when exposed to NH3 gas gradually from 0 to 500 ppm, the wavelength shift data of Eosin-Y was started at 569.5 nm, 573.9 nm, 578.4 nm, 579.4 nm, 580.8 nm, and 582.2 nm, respectively. In applications, the proposed optical dual sensor based on coaxial electrospinning method can detect O2 and NH3 gases simultaneously.

Effects of NiO, SnO2, and Ni-doped SnO2 semiconductor metal oxides on the oxygen sensing capacity of H2TPP

Improving the performance of optical oxygen sensors can be accomplished by adding metal oxide semiconductors (MOSs) additives to the composition comprising an oxygen-sensing agent immobilized in a polymeric thin film. For several decades, MOSs have attracted great interest in gas sensors due to their high sensitivity to many target gasses. Herein, meso-tetraphenylporphyrin (H₂TPP) dye was immobilized into the poly(1-trimethylsilyl-1-propyne) (poly(TMSP)) silicone rubber in the presence of NiO, SnO₂, Ni:SnO₂ metal oxide particles as additives, and their thin films were prepared to investigate oxygen-sensitive optical chemical sensor properties. The characterizations of the synthesized metal oxide powders were carried out through XPS, XRD, FT-IR, PL spectroscopy and SEM methods. Intensity-based spectra and decay kinetics of H₂TPP-based thin films were investigated for the concentration range of 0%-100% [O₂]. The oxygen sensitivity (I₀/I₁₀₀) of the porphyrin was calculated as 70%. Whereas the relative signal intensity values of H₂TPP-based sensor slides were measured as 75%, 80%, and 88% in the presence of NiO, SnO₂, Ni:SnO₂ additives, respectively. The H₂TPP in combination with Ni:SnO₂ semiconductor provided a higher I₀/I₁₀₀ value, larger response range, higher Stern-Volmer constant (K_SV) value, and faster response time compared to the undoped form, and also NiO and SnO₂ additive-doped forms of H₂TPP. The response and the recovery times of the porphyrin-based sensing slide along with Ni:SnO₂ additives have been measured as 12 and 50 s. These results make the H₂TPP along with the MOSs promising candidates as oxygen probes.

Porous matrix materials in optical sensing of gaseous oxygen

The review provides comparison of porous materials that act as a matrix for luminescent oxygen indicators. These include silica-gels, sol–gel materials based on silica and organically modified silica (Ormosils), aerogels, electrospun polymeric nanofibers, metal–organic frameworks, anodized alumina, and various other microstructured sensor matrices. The influence of material structure and composition on the efficiency of oxygen quenching and dynamic response times is compared and the advantages and disadvantages of the materials are summarized to give a guide for design and practical application of sensors with desired sensitivity and response time.

A Phosphorescence Quenching-Based Intelligent Dissolved Oxygen Sensor on an Optofluidic Platform

Continuous measurement of dissolved oxygen (DO) is essential for water quality monitoring and biomedical applications. Here, a phosphorescence quenching-based intelligent dissolved oxygen sensor on an optofluidic platform for continuous measurement of dissolved oxygen is presented. A high sensitivity dissolved oxygen-sensing membrane was prepared by coating the phosphorescence indicator of platinum(II) meso-tetrakis(pentafluorophenyl)porphyrin (PtTFPP) on the surface of the microfluidic channels composed of polydimethylsiloxane (PDMS) microstructure arrays. Then, oxygen could be determined by its quenching effect on the phosphorescence, according to Stern–Volmer model. The intelligent sensor abandons complicated optical or electrical design and uses a photomultiplier (PMT) counter in cooperation with a mobile phone application program to measure phosphorescence intensity, so as to realize continuous, intelligent and real-time dissolved oxygen analysis. Owing to the combination of the microfluidic-based highly sensitive oxygen sensing membrane with a reliable phosphorescent intensity detection module, the intelligent sensor achieves a low limit of detection (LOD) of 0.01 mg/L, a high sensitivity of 16.9 and a short response time (22 s). Different natural water samples were successfully analyzed using the intelligent sensor, and results demonstrated that the sensor features a high accuracy. The sensor combines the oxygen sensing mechanism with optofluidics and electronics, providing a miniaturized and intelligent detection platform for practical oxygen analysis in different application fields.

Polymer matrix: A good substrate material for oxygen probes used in pressure sensitive paints

Over the past few years, surface pressure measurement has fundamental importance in many areas, particularly, aerodynamic research. Conventional methods involve pressure taps, but due to the nature of these pressure taps, only pressure information of isolated points on model surface is available, which limit their applications in aerodynamics studies. Recently the newly developed approach, pressure sensitive paint (PSP) has revolutionized such pressure measurements and various PSP materials have been developed for aerodynamics research. Hence, the main focus of this review is to study the interactions of polymers with different oxygen probes and polymeric role as supporting material in the maturation of PSP. In this review, the selected PSP materials are categorically elucidated in terms of their advantages and limitations to give a fair insight about their applicability. Further, we have summarized and articulated such particular optical oxygen sensing materials either that have been used as PSP or have potential to be used as PSP materials.

Conjugated Copolymers through Electrospinning Synthetic Strategies and Their Versatile Applications in Sensing Environmental Toxicants, pH, Temperature, and Humidity

Conjugated copolymers (CCPs) are a class of polymers with excellent optical luminescent and electrical conducting properties because of their extensive π conjugation. CCPs have several advantages such as facile synthesis, structural tailorability, processability, and ease of device fabrication by compatible solvents. Electrospinning (ES) is a versatile technique that produces continuous high throughput nanofibers or microfibers and its appropriate synchronization with CCPs can aid in harvesting an ideal sensory nanofiber. The ES-based nanofibrous membrane enables sensors to accomplish ultrahigh sensitivity and response time with the aid of a greater surface-to-volume ratio. This review covers the crucial aspects of designing highly responsive optical sensors that includes synthetic strategies, sensor fabrication, mechanistic aspects, sensing modes, and recent sensing trends in monitoring environmental toxicants, pH, temperature, and humidity. In particular, considerable attention is being paid on classifying the ES-based optical sensor fabrication to overcome remaining challenges such as sensitivity, selectivity, dye leaching, instability, and reversibility.