A sensitive and selective electrochemical sensor based on molecularly imprinted polymer for the assay of teriflunomide

An electrochemical sensor based on carbon nanofiber and molecular imprinting strategy for dasatinib recognition

Herein, we proposed a new approach to design a MIP-based electrochemical sensor with carbon nanofiber (CNF), which could improve its conductivities as well as electrode sensitivity and successful detection of dasatinib (DAS). CNFs are capable of forming high porosity with significant interconnected porous networks. The poly(2-hydroxyethyl-methacrylate-N-methacryloyl-L-tyrosine) (PHEMA-MATyr) copolymer was synthesized in the presence of both CNF and DAS by photopolymerization. After optimization of the parameters, the modified MIP-based electrochemical sensor demonstrated the ability to determine the DAS in the linear working range of 1.0 × 10-14-1.0 × 10-13 M for the standard solution and commercial serum samples with a LOD of 1.76 × 10-15 and 2.46 × 10-15, respectively. Good linearity for DAS was observed with correlation coefficients (r) of 0.996 and 0.997 for the standard solution and commercial serum samples, respectively. The recoveries of the DAS ranged from 99.45 % to 99.53 % for the tablet dosage form and commercial serum samples, with average relative standard deviations below 1.96 % in both cases. The proposed modified sensor demonstrated significant sensitivity and selectivity for the rapid determination of DAS in commercial serum samples and tablet form.

Molecularly imprinted polymers-aptamer electrochemical sensor based on dual recognition strategy for high sensitivity detection of chloramphenicol

In this paper, an electrochemical sensor based on a dual recognition strategy of molecularly imprinted polymers (MIPs) and aptamer (Apt) has been designed for the high sensitivity detection of chloramphenicol (CAP). Here, MIPs and Apt have provided dual recognition sites to greatly improve the specific recognition ability of the sensor. Chitosan-multi-walled carbon nanotubes (CS-MWNTs) and AuNPs (gold nanoparticles) have been used for their excellent electrical conductivity. When CAP existed in the detection environment, the imprinted cavities with specific recognition ability bound to CAP through forces such as hydrogen bonds. It hindered the rate of electron transfer and resulted in a decrease in current value. Quantitative detection of CAP could be achieved after analyzing the relationship between the concentration of CAP and the change of current value. After optimizing the experimental parameters, the detection range of the sensor was 10-8 g/L-10-2 g/L with the limit of detection of 3.3 × 10-9 g/L, indicating that the sensor had a high practical application potential.

Monitoring of Medical Wastewater by Sensitive, Convenient, and Low-Cost Determination of Small Extracellular Vesicles Using a Glycosyl-Imprinted Sensor

The monitoring of small extracellular vesicles (sEVs) in medical waste is of great significance for the prevention of the spread of infectious diseases and the treatment of environmental pollutants in medical waste. Highly sensitive and selective detection methods are urgently needed due to the low content of sEVs in waste samples and the complex sample composition. Herein, a glycosyl-imprinted electrochemical sensor was constructed and a novel strategy for rapid, sensitive, and selective sEVs detection was proposed. The characteristic trisaccharide at the end of the glycosyl chain of the glycoprotein carried on the surface of the sEVs was used as the template molecule. The glycosyl-imprinted polymer films was then prepared by electropolymerization with o-phenylenediamine (o-PD) and 3-aminophenylboronic acid (m-APBA) as functional monomers. sEVs were captured by the imprinted cavities through the recognition and adsorption of glycosyl chains of glycoproteins on sEVs. The m-APBA molecule also acted as a signal probe and was then attached on the immobilized glycoprotein on the surface of sEVs by boric acid affinity. The electrochemical signal of m-APBA was amplificated due to the abundant glycoproteins on the surface of sEVs. The detection range of the sensor was 2.1 × 104 to 8.7 × 107 particles/mL, and the limit of detection was 1.7 × 104 particles/mL. The sensor was then applied to the determination of sEVs in medical wastewater and urine, which showed good selectivity, low detection cost, and good sensitivity.

The Effect of Polymerization Techniques on the Creation of Molecularly Imprinted Polymer Sensors and Their Application on Pharmaceutical Compounds

Molecularly imprinted polymers (MIPs) have become more prevalent in fabricating sensor applications, particularly in medicine, pharmaceuticals, food quality monitoring, and the environment. The ease of their preparation, adaptability of templates, superior affinity and specificity, improved stability, and the possibility for downsizing are only a few benefits of these sensors. Moreover, from a medical perspective, monitoring therapeutic medications and determining pharmaceutical compounds in their pharmaceutical forms and biological systems is very important. Additionally, because medications are hazardous to the environment, effective, quick, and affordable determination in the surrounding environment is of major importance. Concerning a variety of performance criteria, including sensitivity, specificity, low detection limits, and affordability, MIP sensors outperform other published technologies for analyzing pharmaceutical drugs. MIP sensors have, therefore, been widely used as one of the most crucial techniques for analyzing pharmaceuticals. The first part of this review provides a detailed explanation of the many polymerization techniques that were employed to create high-performing MIP sensors. In the subsequent section of the review, the utilization of MIP-based sensors for quantifying the drugs in their pharmaceutical preparation, biological specimens, and environmental samples are covered in depth. Finally, a critical evaluation of the potential future research paths for MIP-based sensors clarifies the use of MIP in pharmaceutical fields.

Designing an electrochemical sensor based on ZnO nanoparticle-supported molecularly imprinted polymer for ultra-sensitive and selective detection of sorafenib

BACKGROUND

Sorafenib (SOR) is a multikinase inhibitor anticancer drug that is used in treating non-small cell lung cancer. In this work, we focused on developing nanomaterial-supported smart porous interfaces by following the molecular imprinting approach for the selective determination of SOR. Determination-based studies in the literature for SOR are limited, and they are chromatographic techniques-based; hence, there is a need in the literature to elaborate the selective and sensitive analysis/monitoring of SOR in both biological and pharmaceutical samples with more studies.

RESULTS

The results showed that adding ZnO NPs enhanced the signal five times compared to the solo molecularly imprinted polymer (MIP). Under the optimized conditions, ZnO/AMPS@MIP-GCE showed a linear response in the concentration range between 1.0 × 10-12 and 1.0 × 10-11 M with LOD and LOQ values of 2.25 × 10-13 M and 7.51 × 10-13 M, respectively, in the serum sample. The selectivity study was conducted against common cations, anions, and compounds such as dopamine, paracetamol, ascorbic acid, and uric acid. Also, the imprinting factor (IF) analysis was performed on selected drug substances having structural similarities to SOR and the relative IF values of regorafenib, leflunomide, teriflunomide, nilotinib, axitinib, and dasatinib indicated the selectivity of the developed sensor for SOR. Finally, ZnO/AMPS@MIP-GCE was implemented to determine SOR in the spiked commercial human serum samples and tablet dosage form with bias% between -0.43 and + 0.66.

SIGNIFICANCE AND NOVELTY

This study is the first electrochemical study for the determination of SOR, and thanks to the ZnO NPs supported MIP sensor, it stands out in terms of both high sensitivity and superior selectivity. Also, this designed sensor provides controlled orientation of the template and complete removal of templates in a one-step process, allowing extremely low detection and quantification limits.

Molecularly imprinted electrochemical sensor for the selective and sensitive determination of octreotide in cancer patient plasma sample

In this study, a molecularly imprinted polymer film (P (ANI)@MIP) on the electrode surface was fabricated using aniline as a functional monomer and octreotide (OC) as a template molecule. The developed P (ANI)@MIP was electrochemically electropolymerized on a glassy carbon electrode (GCE) surface. Each step of MIP production was evaluated by viewing the [Fe (CN)₆]^3-/4- signal obtained using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The P (ANI)@MIP film layer was studied with a scanning electron microscope (SEM), Raman, and contact angle measurements. The parameters consisting of monomer, template ratio, cycle number, removal solution, removal time, and rebinding time were optimized to obtain the best electrochemical sensor. The developed method was validated in line with ICH guidelines. The linear range, LOD, and LOQ were found as 10-80 fM, 0.801 fM, and 2.670 fM, respectively. The selectivity of the method was tested with the response of somatostatin and lanreotide from the same growth hormone family by comparing the OC response. The developed P (ANI)@MIP/GCE sensor is the first reported method for electrochemical analysis of OC. The P (ANI)@MIP/GCE sensor exhibited high sensitivity and selectivity for OC. The novel MIP sensor was used to determine OC in cancer patient plasma samples. The concentration of OC in cancer patients varied between 8.98 ng/mL and 10.10 ng/mL.

The electrochemical quantitation method for sugammadex via a molecularly imprinted polymer-based sensor

Sugammadex (SUG) is a synthetically modified γ-cyclodextrin derivative used in hospitals after surgeries to reverse the neuromuscular blockade induced by rocuronium or vecuronium. In this study, we aimed to develop the first electroanalytical quantification method for sugammadex by using molecular imprinting (MIP) via the electropolymerization (EP) technique. An EP-MIP film was formed by EP on a screen-printed gold electrode (SPAuE) and a new electrochemical sensor, EP-MIP(SUG)/SPAuE, was fabricated using the 4-aminophenol monomer with copper ions to enhance the MIP-binding site. Surface and electrochemical characterization of the EP-MIP(SUG)/SPAuE sensor have been done via scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). After screening and optimization studies were carried out to fabricate a MIP-based electrochemical sensor, the analytical performance of EP-MIP(SUG)/SPAuE and the validation parameters were tested according to the ICH guidelines. The specificity/selectivity of the developed sensor has been shown by using common interferents found in the biological fluids and also molecules having similar structures, such as α-cyclodextrin, β-cyclodextrin, and γ-cyclodextrin. As a result, a quantitative analysis method has been developed and validated by using the EP-MIP(SUG)/SPAuE sensor in the concentration range of 0.1-1.0 pM with very high sensitivity (limit of detection: 27.3 fM). The applicability of the method has been shown for bulk drug substances, pharmaceutical dosage forms, and commercial serum samples with good recovery and RSD% results. The EP-MIP(SUG)/SPAuE is the first electrochemical sensor developed for the determination of sugammadex serving the aims of simplicity, short analysis time, and low cost, and has the potential to be adapted in the future as a portable and/or wearable sensor via miniaturization.