Preparation and characterization of activated carbon from agricultural wastes and their ability to remove chlorpyrifos from water

Agricultural biomass/waste-based materials could be a potential adsorption-type remediation contributor to environmental pollution induced by pesticides-A critical review

The widespread use of pesticides that are inevitable to keep the production of food grains brings serious environmental pollution problems. Turning agricultural biomass/wastes into materials addressing the issues of pesticide contaminants is a feasible strategy to realize the reuse of wastes. Several works summarized the current applications of agricultural biomass/waste materials in the remediation of environmental pollutants. However, few studies systematically take the pesticides as an unitary target pollutant. This critical review comprehensively described the remediation effects of crop-derived waste (cereal crops, cash crops) and animal-derived waste materials on pesticide pollution. Adsorption is considered a superior and highlighted effect between pesticides and materials. The review generalized the sources, preparation, characterization, condition optimization, removal efficiency and influencing factors analysis of agricultural biomass/waste materials. Our work mainly emphasized the promising results in lab experiments, which helps to clarify the current application status of these materials in the field of pesticide remediation. In the meantime, rigorous pros and cons of the materials guide to understand the research trends more comprehensively. Overall, we hope to achieve a large-scale use of agricultural biomass/wastes.

Waste newspaper as cellulose resource of activated carbon by sodium salts for methylene blue and congo red removal

The work was aimed at evaluating the adsorptive properties of waste newspaper (WN) activated carbons chemically produced using sodium salts for methylene blue (MB) and congo red (CR) removal. The activated carbons, designated as AC1, AC2, AC3 and AC4 were prepared through impregnation with NaH2PO4, Na2CO3, NaCl and NaOH, respectively and activation at 500 °C for 1 h. The activated carbons were characterized for surface chemistry, thermal stability, specific area, morphology and composition. The AC1 with a surface area of 917 m2/g exhibits a greater MB capacity of 651 mg/g. Meanwhile, a greater CR capacity was recorded by AC2 at 299 mg/g. The pseudo-second order model fitted well with the kinetic data, while the equilibrium data could be described by Langmuir model. The thermodynamic parameters, i.e.., positive ΔH°, negative ΔG° and positive ΔS° suggest that the adsorption of dyes is endothermic, spontaneous and feasible at high solution temperature. To conclude, WN is a potential cellulose source for producing activated carbon, while NaH2PO4 activation could be employed to convert WN into activated carbon for effective dye wastewater treatment.

Steric and energetic studies on the influence of cellulose on the adsorption effectiveness of Mg trapped hydroxyapatite for enhanced remediation of chlorpyrifos and omethoate pesticides

Magnesium-trapped hydroxyapatite (Mg.HP) was hybridized with cellulose fiber to produce a bio-composite (CLF/HP) with enhanced adsorption affinities for two types of toxic pesticides (chlorpyrifos (CF) and omethoate (OM)). The enhancement influence of the hybridized cellulose on the adsorption performances of Mg.HP was illustrated based on the determined steric and energetic factors. The computed CF and OM adsorption performances of CLF/HP during the saturation phases are 279.8 mg/g and 317.9 mg/g, respectively, which are significantly higher than the determined values using Mg/HP (143.4 mg/g (CF) and 145.3 mg/g (OM)). The steric analysis demonstrates a strong impact of the hybridization process on the reactivity of the surface of the composite. While CLF/HP reflects effective uptake site densities (Nm) of 93.3 mg/g (CF) and 135.3 mg/g (OM), the estimated values for Mg.HP are 51.2 mg/g (CF) and 46.11 mg/g (OM), which explain the reported enhancement in the adsorption performances of the composite. The capacity of each uptake site to be occupied with more than one molecule (n (CF) = 3-3.74 and n (OM) = 2.35-3.54) suggests multimolecular uptake. The energetic factors suggested physical mechanistic processes of spontaneous and exothermic behaviors either during the uptake of CF or OM.

A Sustainable Banana Peel Activated Carbon for Removing Pharmaceutical Pollutants from Different Waters: Production, Characterization, and Application

Due to the growing concerns about pharmaceutical contamination and its devastating impact on the economy and the health of humans and the environment, developing efficient approaches for removing such contaminants has become essential. Adsorption is a cost-effective technique for removing pollutants. Thus, in this work, banana peels as agro-industrial waste were utilized for synthesizing activated carbon for removing pharmaceuticals, namely amoxicillin and carbamazepine from different water matrices. The chemically activated carbon by phosphoric acid (H3PO4) was carbonized at temperatures 350 °C, 450 °C and 550 °C. The material was characterized by several techniques such as scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS), Fourier transform infrared spectroscopy (FTIR), Boehm titration, point of zero charge (pHPZC), BET surface area (SBET), the proximate and ultimate analyses, X-ray powder diffraction (XRD), and thermos-gravimetric analysis (TGA). The SEM of banana peel activated carbon (BPAC) depicted a semi-regular and heterogeneous morphology, characterized by an abundance of pores with diverse forms and sizes. Boehm titration revealed an increase in the amounts of acidic groups by 0.711 mmol/g due to activation by H3PO4. FTIR recorded different peaks suggesting significant modifications in the spectroscopic characteristics of the BPAC surface due to the successful activation and adsorption of the pollutant molecules. The pHpzc of BPAC was calculated to be 5.005. The SBET surface area dramatically increased to 911.59 m2/g after the activation. The optimum conditions were 25 °C, a materials dosage of 1.2 g/L, a saturation time of 120 min, a pollutants mixture of 25 mg/L, and a pH of 5. Langmuir exhibits a slightly better fit than Freundlich with a low value of the residual sum of squares (SSE) and the data were better fitted to the pseudo-second-order kinetic. Furthermore, the efficacy of BPAC in eliminating pharmaceuticals from Milli Q water, lake water, and wastewater was successfully investigated over the seven cycles. The results of the present work highlighted a potential usage of agro-industrial waste in eliminating organic micropollutants while exhibiting sustainable management of this waste.

Stable Supercapacitors Based on Activated Carbon Prepared from Italian Orange Juice

The development of efficient energy storage systems is critical in the transition towards sustainable energy solutions. In this context, the present work investigates the viability of using orange juice, as a promising and sustainable precursor, for the synthesis of activated carbon electrodes for supercapacitor technologies. Through the carbonization-activation process and controlling the preparation parameters (KOH ratio and activation time), we have tailored the specific surface area (SSA) and pore size distribution (PSD) of the resulting carbon materials-crucial parameters that support supercapacitive performance. Several spectroscopic, morphological, and electrochemical techniques are used to characterize the obtained carbon materials. In particular, our optimization efforts revealed that a 5:1 KOH ratio with an activation time up to 120 min produced the highest SSA of about 2203 m2/g. Employing these optimal conditions, we fabricated symmetric coin cell supercapacitors using Na2SO4 as the electrolyte, which exhibited interesting specific capacitance (~56 F/g). Durability testing over 5000 cycles sustained the durability of the as-made activated carbon electrodes, suggesting an excellent retention of specific capacitance. This study not only advances the field of energy storage by introducing a renewable material for electrode fabrication but also contributes to the broader goal of waste reduction through the repurposing of food byproducts.

Enhanced thyroxine removal from micro-polluted drinking water resources in a bio-electrochemical reactor amended with TiO2@GAC particles: Efficiency, mechanism and energy consumption

A three-dimensional bioelectrochemical system (3D-BES) with both electrocatalytic and biodegradation functions was designed and developed to enhance iodine-containing hormone removal from micro-polluted oligotrophic drinking water sources and to reduce energy consumption. Thyroxine (T4) removal efficiency was 99.0% in the 3D-BES amendment with TiO2@GAC as the particle electrodes, which was 20.5% higher than the total efficiency of single biodegradation (28.7%) plus electrochemical decomposition (49.8%). The high T4 removal efficiency was a result of biochemical synergistic degradation, enhancement of electron transfer and utilization, enrichment of functional microorganisms, and the expression of dehalogenation functional genes. The electron transfer was increased by 1.63 times in 3D-BES compared to the 2D-BES, which contributed to: (i) ∼17.8% enhancement of dehalogenation, (ii) 2.35 times enhancement of the attenuation rate, and (iii) 60% reduction in energy consumption. Moreover, the aggregation of microorganisms and the hydrophobic T4 onto TiO2@GAC shortened the transfer distance of matter and energy, which induced the degradation steps to be shortened and the toxic decay to be accelerated from T4 and its metabolites. These comprehensive functions also enhanced the 31.8% ATPase activity, 7.3% abundance of the functional reductive dehalogenation genera, and 52.3% dehalogenation genes expression for Pseudomonas, Ancylobacter, and Dehalogenimonas, which contributed to an increase in T4 removal. This work provides an environmental-friendly biochemical synergistic method for the detoxification of T4 polluted water.

Removal of Cr6+ ions and mordant violet 40 dye from liquid media using Pterocladia capillacea red algae derived activated carbon-iron oxides

In recent years, water pollution has become one of the most dangerous problems facing the world. Pollution of water with heavy metals and different dyes has caused many harmful effects on human health, living organisms and our environment. In this study, iron oxide nanomagnetic composite from Pterocladia Capillacea red algae-derived activated carbon (PCAC-IO) was synthesized by co-precipitation method using different iron salts and different base solutions. The synthesized nanocomposite was investigated with various characterization techniques such as FTIR, BET, SEM-EDX, TEM, XRD, and VSM. The obtained PCAC-IO adsorbent was used for Cr6+ ions and Mordant Violet 40 (MV40) dye removal. The adsorption mechanism of Cr6+ ions and MV40 dye on PCAC-IO was examined using several adsorption and kinetic isotherm models. Langmuir and Freundlich models were investigated using experimental data. Pseudo-first-order (PFO), Pseudo-second-order (PSO) and intraparticle diffusion models (IPDM) were applied to identify the adsorption mechanism. It has shown that the PSO kinetic model fits better with the experimental data obtained from PCAC-IO. This result can be interpreted as the adsorption of the adsorbate on the nanocomposite as chemical adsorption. The optimum conditions for maximum Cr6+ ions removal (96.88%) with PCAC-IO adsorbent occur at room temperature, 5 g L-1 adsorbent concentration, 100 mg L-1 initial pollutant concentration, pH 1 and at the end of 180 min, while maximum MV40 dye removal (99.76%), other conditions being the same, unlikely it occurred at pH 2.06 and after 45 min. The most suitable model for Cr6+ ions removal under the conditions of 1 L-1 g adsorbent concentration and 400 mg L-1 adsorbate concentration was Langmuir (Qmax = 151.52 mg g-1), while for MV40 removal it was Freundlich (Qmax = 303.03 mg g-1). We propose the use of activated carbon-supported iron oxide prepared from bio-waste material, especially from Pterocladia Capillacea red algae, as a promising adsorbent with high efficiency in the removal of Cr6+ ions and MV40 dye from aqueous media.

Adsorptive removal of malachite green dye from aqueous solution using Rumex abyssinicus derived activated carbon

The potential for malachite green dye saturated effluent to severely affect the environment and human health has prompted the search for effective treatment technologies. Thus, this study was conducted with the goal of developing activated carbon from Rumex abyssinicus for the adsorptive removal of malachite green dye from an aqueous solution. Unit operations such as drying, size reduction, impregnation with H3PO4, and thermal activation were used during the preparation of the activated carbon. An experiment was designed considering four main variables at their respective three levels: initial dye concentration (50, 100, and 150 mg/L), pH (3, 6, and 9), contact period (20, 40, and 60 min), and adsorbent dosage (0.05, 0.01, and 0.15 g/100 mL). Optimization of the batch adsorption process was carried out using the Response Surface methodology's Box Behnken approach. The characterization of the activated carbon was described by SEM for surface morphology with cracks and highly porous morphology, FTIR for multi-functional groups O-H at 3506.74 cm-1 and 3290.70 cm-1, carbonyl group stretching from aldehyde and ketone (1900-1700 cm-1), stretching motion of aromatic ring C=C (1543.12 cm-1), stretching motion of -C-H (1500-1200 cm-1), vibrational and stretching motion of -OH (1250.79 cm-1), and vibrational motion of C-O-C (1049.32 cm-1), pHpzc of 5.1, BET for the specific surface area of 962.3 m2/g, and XRD for the presence of amorphous structure. The maximum and minimum dye removal efficiencies of 99.9% and 62.4% were observed at their respective experimental conditions of (100 mg/L, 0.10 mg/100 mL, pH 6, and 40 min) and (100 mg/L, 0.15 mg/100 mL, pH 3, and 20 min), respectively. Langmuir, Freundlich, Toth, and Koble-Corrigan models were used to evaluate the experimental data, in which Koble-Corrigan model was found to be the best fit with the highest value of R2 0.998. In addition to this, the kinetic studies were undertaken using pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Boyd models, and as a result, the pseudo-second-order model proved to have a better fit among the kinetic models. The kinetics and isotherm analysis revealed that the nature of the adsorption to be homogenous and monolayer surfaces driven by chemosorption. Furthermore, the thermodynamics study revealed the nature of adsorption to be feasible, spontaneous, and endothermic. On the other hand, the reusability study depicted the fact that the adsorbent can be utilized for five cycles with a negligible drop in the removal efficiencies from 99.9 to 95.2%. Finally, the low-cost, environmentally benign, and high adsorption capacity of the adsorbent material derived from Rumex abyssinicus stem could be used to treat industrial effluents.

Natural and Natural-Based Polymers: Recent Developments in Management of Emerging Pollutants

Anthropogenic activities lead to the issue of new classes of pollutants in the environment that are not currently monitored in environmental studies. This category of pollutants (known as emerging contaminants) includes a very wide range of target substances, such as pharmaceuticals, plant protection products, personal care products, dyes, toxins, microplastics and many other industrially important intermediaries. Together with an increasing demand for clean water (both for agricultural necessities and for the increasing population consumption), the need for the removal of emerging pollutants, simultaneously with the current "green chemistry" approach, opens the door for the industrial application of natural polymers in the area of environmental protection. Recent developments in this area are presented in this paper, as well as the application of these particular natural materials for the removal of other contaminants of interest (such as radioisotopes and nanoparticles). The current knowledge regarding the processes' kinetics is briefly presented, as well as the future development perspectives in this area.