Recent advances in solid-phase sorbents for sample preparation prior to chromatographic analysis

Development of a disposable paper-based thin film solid-phase microextraction sampling kit to quantify ketone body

Diabetes ketoacidosis (DKA) is a life-threatening complication and requires immediate medical attention in the case of diabetes subjects, especially in the case of type 1 diabetes mellitus. In the condition of DKA, the body produces an excess amount of ketone bodies after unregulated fat degradation, causing blood to become acidic and hampering the regular metabolic activities of the body. The current diagnostic technique for DKA condition is based on monitoring ketone bodies, especially β-hydroxybutyric acid, from human urine and blood samples. The detection of serum ketone bodies in pathology is sometimes limited due to false positive results and the lack of standardization for precise quantification of analytes. In this study, a paper-based patch operating on the thin film solid-phase microextraction (TF-SPME) principle was developed and it was coupled with gas chromatography-mass spectrometry for simple quantification of β-hydroxybutyric acid (BHB) ketone body from a phosphate-buffered saline matrix. To fabricate the paper-based TF-SPME patches, a regular A4 sheet paper sheet was utilized as the substrate and uniform coating by multiwalled carbon nanotubes (MWCNT), polydimethylsiloxane (PDMS) and divinyl benzene (DVB) compounds was performed with an automatic film applicator. The 70 μm paper-based coated sheet was trimmed into 4 cm × 1 cm dimension pieces to obtain multiple patches from a single sheet. Extraction of the BHB ketone body into the closed vials was performed by exploiting the individual DVB/PDMS and DVB/CNT/PDMS paper patches followed by desorption with acetonitrile before quantification by gas chromatography-mass spectrometry analysis. Our study showed that the BHB extraction efficiency of DVB/PDMS-coated patches was higher than that of DVB/CNT/PDMS. The outcome showed a good linearity (R 2 = 0.99) within the 500-20 000 ng mL-1 concentration range of BHB by paper-based DVB/PDMS patches. This study demonstrated the feasibility of utilizing simple, cost-effective paper-based disposable TF-SPME patches as a sampling kit for future screening of diabetes ketoacidosis without the need for prolonged traditional sample preparation in pathology.

Overview of Liquid Sample Preparation Techniques for Analysis, Using Metal-Organic Frameworks as Sorbents

The preparation of samples for instrumental analysis is the most essential and time-consuming stage of the entire analytical process; it also has the greatest impact on the analysis results. Concentrating the sample, changing its matrix, and removing interferents are often necessary. Techniques for preparing samples for analysis are constantly being developed and modified to meet new challenges, facilitate work, and enable the determination of analytes in the most comprehensive concentration range possible. This paper focuses on using metal-organic frameworks (MOFs) as sorbents in the most popular techniques for preparing liquid samples for analysis, based on liquid-solid extraction. An increase in interest in MOFs-type materials has been observed for about 20 years, mainly due to their sorption properties, resulting, among others, from the high specific surface area, tunable pore size, and the theoretically wide possibility of their modification. This paper presents certain advantages and disadvantages of the most popular sample preparation techniques based on liquid-solid extraction, the newest trends in the application of MOFs as sorbents in those techniques, and, most importantly, presents the reader with a summary, which a specific technique and MOF for the desired application. To make a tailor-made and well-informed choice as to the extraction technique.

Enhancing verapamil trace determination from biological matrices by bar adsorptive microextraction

Verapamil is an L-type calcium channel blocker widely used in the treatment of cardiovascular diseases such as hypertension, angina and arrhythmias, requiring accurate therapeutic monitoring to maintain plasma, urine and saliva concentrations within a safe range. In this context, a novel analytical approach has been proposed to determine verapamil in biological samples, using bar adsorptive microextraction coated with reversed-phase polymers followed by high-performance liquid chromatography with diode array detection. Two adsorbents have been chosen, i.e. STRATA-CN and ENVI-18 polymers, showing recoveries from 56.01 ± 2.16% to 96.82 ± 0.61% under optimized experimental conditions, such as sample pH: 10.0 (STRATA-CN) and 8.0 (ENVI-18), 2 h of equilibrium time, stirring speed at 990 rpm, back-extraction solvent using methanol:acetonitrile (1 : 1 v/v), and 1 h under sonication. The analytical method showed linearity from 20 to 600 ng mL-1 (r ≥ 0.99), as well as adequate precision (with RSD% below 15%) and accuracy (with RE% within 15% of the nominal value). Finally, the analytical method was applied to plasma, urine and saliva samples and proved to be a promising alternative for the trace analysis of verapamil in biological matrices.

Nanoparticle Assisted Fabric Phase Sorptive Extraction for Azo Dye Determination in the Industrial Sewage

Currently, one of the significant environmental problems is the presence of azo dye materials in water sources. In this study, for the first time, a fast and sensitive sample preparation approach using nanoparticle-assisted fabric phase sorptive extraction (NFPSE) followed by high-performance liquid chromatography was examined to remove some azo dyes such as methyl red and sunset yellow from aqueous solutions. Primarily, the significance of several parameters affecting NFPSE, such as fabric type, the kind of sorbent, the number of contacts with sol-gel and the time of contact, was investigated. In addition, experiments were performed to determine the effect of different adsorption parameters, such as sample volume, adsorption time, adsorbent value, desorption time, ionic strength and pH. It was found that the calibration curve was linear within two ranges of concentrations (0.05-0.1 and 0.5-15 ng/L for methyl red; 0.05-0.5 and 0.5-15 ng/L for sunset yellow) with correlation coefficients better than 0.9683. The limit of detection was 0.014 ng/L for methyl red and 0.015 ng/L for sunset yellow. Repeatability Relative Standard Deviation (RSD) with three replicated experiments was 1.5-10% for methyl red and 2.5-5.8% for sunset yellow. Relative recovery percentages of 88-96% for methyl red and 62-92% for sunset yellow were obtained in the samples. Moreover, the results have shown that acceptable accuracy, precision and linearity make the "fabric phase sorptive extraction" a proper method for the determination of dyes from industrial sewage samples.

Revealing nitrogenous VX metabolites and the whole-molecule VX metabolism in the urine of guinea pigs

VX, a well-known organophosphorus nerve agent (OPNA), poses a significant threat to public safety if employed by terrorists. Obtaining complete metabolites is critical to unequivocally confirm its alleged use/exposure and elucidate its whole-molecular metabolism. However, the nitrogenous VX metabolites containing 2-diisopropylaminoethyl moiety from urinary excretion remain unknown. Therefore, this study applied a newly developed untargeted workflow platform to discover and identify them using VX-exposed guinea pigs as animal models. 2-(N,N-diisopropylamino)ethanesulfonic acid (DiPSA) was revealed as a novel nitrogenous VX metabolite in urine, and 2-(Diisopropylaminoethyl) methyl sulfide (DAEMS) was confirmed as another in plasma, indicating that VX metabolism differed between urine and plasma. It is the first report of a nitrogenous VX metabolite in urine and a complete elucidation of the VX metabolic pathway. DiPSA was evaluated as an excellent VX exposure biomarker. The whole-molecule VX metabolism in urine was characterized entirely for the first time via the simultaneous quantification of DiPSA and two known P-based biomarkers. About 52.1% and 32.4% of VX were excreted in urine as P-based and nitrogenous biomarkers within 24 h. These findings provide valuable insights into the unambiguous detection of OPNA exposure/intoxication and human and environmental exposure risk assessment.

Functionalized magnetic nanomaterials as recyclable adsorbents for efficient flavonoid enrichment in Scutellaria Radix

A magnetic composite (Fe3O4@SiO2@PNIPAM-co-NHMA) with high adsorption capacity and recoverability was developed for the enrichment and determination of flavonoids in Scutellaria Radix (SR). A magnetic solid-phase extraction (MSPE) technique using Fe3O4@SiO2@PNIPAM-co-NHMA absorbent in combination with high-performance liquid chromatography (HPLC) was developed for selectively enrichment and determination of the biologically active flavonoids in the aqueous extract of SR, including baicalein, baicalin, wogonoside and wogonin. Under the optimized experimental conditions, the magnetic adsorbent could adsorb up to 77.0 ± 0.98 % - 98.15 ± 0.15 % of four representative flavonoids from SR, with elution rates varying from 55.10 ± 0.25 % to 91.94 ± 1.85 %. The limits of detection (LOD) and limits of quantitation (LOQ) were 0.01-0.35 μg/mL and 0.03-0.98 μg/mL, respectively. In addition, it remained effective after six replicates, demonstrating its potential as a recoverable adsorbent for enriching flavonoids in traditional Chinese medicine.

Innovative Solid-Phase Extraction Strategies for Improving the Advanced Chromatographic Determination of Drugs in Challenging Biological Samples

In the past few decades, considerable scientific strides have been made in the subject of drug analysis in human biological samples. However, the risk caused by incorrect drug plasma levels in patients still remains an important concern. This review paper attempts to investigate the advances made over the last ten years in common sample preparation techniques (SPT) for biological samples based on solid sorbents, including solid-phase extraction (SPE) and solid-phase micro-extraction (SPME), and in particular in the field of molecularly imprinted polymers (MIPs), including non-stimuli-responsive and stimuli-responsive adsorbents. This class of materials is known as 'smart adsorbents', exhibiting tailored responses to various stimuli such as magnetic fields, pH, temperature, and light. Details are provided on how these advanced SPT are changing the landscape of modern drug analysis in their coupling with liquid chromatography-mass spectrometry (LC-MS) analytical techniques, a general term that includes high-performance liquid chromatography (HPLC) and ultra-high performance liquid chromatography (UHPLC), as well as any variation of MS, such as tandem (MS/MS), multiple-stage (MSn), and high-resolution (HRMS) mass spectrometry. Some notes are also provided on coupling with less-performing techniques, such as high-performance liquid chromatography with ultraviolet (HPLC-UV) and diode array detection (HPLC-DAD) detection. Finally, we provide a general review of the difficulties and benefits of the proposed approaches and the future prospects of this research area.

Chromatographic Methods for the Determination of Organic Pollution in Urban Water: A Current Mini Review

The number of pollutants and chemicals with the potential to reach the environment is still largely unknown, which poses great challenges for researchers in various fields of science, environmental scientists, and analytical chemists. Chromatographic techniques, both gas chromatography (GC) and liquid chromatography (LC) coupled with different types of detection, are now invaluable tools for the identification of a wide range of chemical compounds and contaminants in water. This review is devoted to chromatographic techniques GC-MS, GC-Orbitrap-MS, GC-MS/MS, GC-HRMS, GC × GC-TOFMS, GC-ECD, LC-MS/MS, HPLC-UV, HPLC-PDA, UPLC-QTOFMS, used to determinate emerging organic contaminants in aquatic media, mainly in urban water, published in the scientific literature over the past several years. The article also focuses on sample preparation methods used in the analysis of aqueous samples. Most research focuses on minimizing the number of sample preparation steps, reducing the amount of solvents used, the speed of analysis, and the ability to apply it to a wide range of analytes in a sample. This is extremely important in the application of sensitive and selective methods to monitor the status of urban water quality and assess its impact on human health.

MOF-801 based solid phase microextraction fiber for the monitoring of indoor BTEX pollution

Benzene, toluene, ethylbenzene and xylenes (BTEX) are some of the better-known indoor air pollutants, for which effective monitoring is important. The analysis of BTEX can be performed by different type of solid phase microextraction (SPME) fibers. This study presents a proposal for a low cost, convenient and environmentally friendly analytical method for the determination of BTEX in air samples using custom made SPME fibers. In this context, custom made metal organic frameworks (MOF-801) were coated on a stainless-steel wire for SPME fiber preparation. The analysis of BTEX was performed by introducing SPME fiber into an analyte-containing Tedlar bag in steady-state conditions. After the sampling step, the analytes were analyzed using gas chromatography mass spectrometry in selected ion monitoring mode. Parameters that affect the analysis results were optimized; these include desorption temperature and time, preconditioning time, extraction temperature and time, and sample volume. Under optimized conditions, analytical figure of merits of developed method were obtained, including limits of detection (LOD) (0.012 - 0.048 mg/m3), linear ranges (0.041-18 mg/m3), intraday and interday repeatability (2.08 - 4.04% and 3.94 - 6.35%), and fiber to fiber reproducibility (7.51 - 11.17%). The proposed method was successfully applied to real air samples with an acceptable recovery values between 84.5% and 110.9%. The developed method can be applied for the effective monitoring of BTEX.

One Pot Synthesis of Nanofiber-Coated Magnetic Composites as Magnetic Dispersive Solid-Phase Extraction Adsorbents for Rapid Determination of Tetracyclines in Aquatic Food Products

A magnetic adsorbent based on a C-nanofiber (Fe3O4@C-NFs) nanocomposite was synthesized using a simple one-pot co-precipitation method. The characterized results showed that the obtained C-nanofiber-coated magnetic nanoparticles had many attractive features such as a large specific surface area and a highly interwoven and branched mesoporous structure, as well as distinguished magnetism. The nanocomposite was then used as an adsorbent in the magnetic solid phase extraction (MSPE) of four typical tetracyclines (oxytetracycline, tetracycline, chlortetracycline, and doxycycline) in aquatic products. The TCs in the extract were determined using ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). Experimental variables of MSPE, including the sorbent amount, pH condition, adsorption and desorption time, and desorption solvent, were investigated and optimized systematically. The method validation indicated that the developed method showed good linearity (R2 > 0.995) in the range of 1.0-200 ng/mL. The average recoveries at the spiked levels ranged from 90.7% to 102.7% with intra-day and inter-day relative standard deviations (RSDs, n = 6) ranging from 3.72% to 8.17% and 4.20% to 9.69%, respectively. The limit of detection (LOD) and limit of quantification (LOQ) for the four kinds of TCs were 0.7 μg/kg and 2.0 μg/kg, respectively. Finally, MSPE based on C-nanofiber-coated magnetic nanoparticles was successfully applied to TC analysis in real aquatic products (grass carp, large yellow croaker, snakehead, mandarin fish, Penaeus vannamei, swimming crab, etc.). Compared with traditional extraction methods, the proposed method for TC analysis in aquatic products is more sensitive, effective, recyclable, and environmentally friendly.

Dispersive Micro-Solid Phase Extraction Using a Graphene Oxide Nanosheet with Neocuproine and Batocuproine for the Preconcentration of Traces of Metal Ions in Food Samples

A dispersive micro-solid phase extraction (Dµ-SPE) method for the preconcentration of trace metal ions (Pb, Cd, Cr, Mn, Fe, Co, Ni, Cu, Zn) on graphene oxide with the complexing reagents neocuproine or batocuproine is presented here. Metal ions form cationic complexes with neocuproine and batocuproine. These compounds are adsorbed on the GO surface via electrostatic interactions. The factors affecting the separation and preconcentration of analytes such as pH, eluent (concentration, type, volume), amount of neocuproine, batocuproine and GO, mixing time, and sample volume were optimized. The optimal sorption pH was 8. The adsorbed ions were effectively eluted with 5 mL 0.5 mol L^-1 HNO₃ solution and determined by the ICP-OES technique. The preconcentration factor for the GO/neocuproine and GO/batocuproine in the range 10-100 and 40-200 was obtained for the analytes, with detection limits of 0.035-0.84 ng mL^-1 and 0.047-0.54 ng mL^-1, respectively. The method was validated by the analysis of the three certified reference materials: M-3 HerTis, M-4 CormTis, and M-5 CodTis. The procedure was applied to determine metal levels in food samples.

Novel amino-functionalized magnetic metal-organic framework/layered double hydroxide adsorbent for microfluidic solid phase extraction: Application for vitamin D3

Vitamin D deficiency is highly prevalent worldwide, especially with limited sun exposure and sun avoidance. Thus, reliable monitoring of vitamin D levels in food and biological samples is vital for medicinal diagnosis. Herein, a potent method for the extraction and determination of vitamin D₃ is presented using a microchip-based solid-phase extraction (SPE) device followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) detection. A new magnetic adsorbent based on Fe₃O₄ magnetic nanoparticles (MNPs) modified ZnFe layered double hydroxide (LDH)/2-aminoterephthalic acid-Zn²⁺ metal-organic framework (IRMOF-3) composite (IRMOF-3@MLDH) was successfully synthesized and fixed inside a rectangular micro-column (4 × 2 × 12 mm). The porous structure and high surface area of IRMOF-3@MLDH provide abundant adsorbing sites and make it a potent SPE adsorbent, with an exceptional ability to retain vitamin D₃. The adsorption isotherm showed that the composite was highly efficient at extracting vitamin D₃ with an extraction capacity of 126 mg g^-1. The designed extraction microchip simplified the SPE process, paving the way for automated SPE systems. The developed method presented a broad linear range of 5-2000 ng mL^-1, with a detection limit of 1.4 ng mL^-1. In comparison to conventional silica-based adsorbents, a higher sensitivity was obtained in the determination of vitamin D₃ using the IRMOF-3@MLDH adsorbent. The selectivity of the method was also satisfactory, enabling the measurement of vitamin D₃ in food and blood samples with high recovery values in the range from 95.2 to 101%. Thus, the newly developed adsorbent and method offer an efficient alternative to the commonly used C18-based approach.

Utilization of Waste Biomaterial as an Efficient and Eco-Friendly Adsorbent for Solid-Phase Extraction of Pantoprazole Contaminants in Wastewater

The objective of this analysis is to establish the potential of biodegradable agro-industrial waste materials as biosorbents in the solid-phase extraction (SPE) technique for sample preparation. In this regard, waste coffee husk (CH) powder was collected, washed, treated chemically, characterized, and applied as an SPE adsorbent to extract pantoprazole from the wastewater samples. Sample detection was accomplished using the UPLC-MS/MS system. The positive mode of electrospray ionization was exploited for the ionization of the sample, and quantification of the target analyte was performed by the multiple reaction monitoring modes. The precursor to product ion transition of 384.02→1380.05 and 384.02→200.05 was used as qualifiers and quantifiers, respectively. Optimization of the particle size, adsorbent dose, and contact time were evaluated to select the best combination of features. The efficiency and regeneration capability of the CH were compared with respect to a commercially available silica-based C18 SPE adsorbent, and it was found that CH possessed comparable (~50%) extraction, as well as regeneration capacity (~95%). The developed biosorbent was applied in a wastewater sample spiked with the target analyte and recovery studies were performed, which found a range of 93.0 to 102.0% with a %RSD of 3.72 to 12.7%. Thus, CH can be exploited as a ‘greener’ replacement for the commercially available adsorbents for the extraction/retention of active pharmaceutical ingredients present in water/wastewater samples.

An Imine-Based Porous 3D Covalent Organic Polymer as a New Sorbent for the Solid-Phase Extraction of Amphenicols from Water Sample

In this paper, an imine-based porous 3D covalent organic polymer (COP) was synthesized via solvothermal condensation. The structure of the 3D COP was fully characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, transmission electron microscopy, and powder X-ray diffractometry, thermogravimetric analysis, and Brunauer-Emmer-Teller (BET) nitrogen adsorption. This porous 3D COP was used as a new sorbent for the solid-phase extraction (SPE) of amphenicol drugs, including chloramphenicol (CAP), thiamphenicol (TAP), and florfenicol (FF) in aqueous solution. Factors were investigated for their effects on the SPE efficiency, including the types and volume of eluent, washing speed, pH, and salinity of water. Under the optimized conditions, this method gave a wide linear range (0.1-200 ng/mL) with a high correlation coefficient value (R² > 0.99), low limits of detection (LODs, 0.01-0.03 ng/mL), and low limits of quantification (LOQs, 0.04-0.10 ng/mL). The recoveries ranged from 83.98% to 110.7% with RSDs ≤ 7.02%. The good enrichment performance for this porous 3D COP might contribute to the hydrophobic and π-π interactions, the size-matching effect, hydrogen bonding, and the good chemical stability of 3D COP. This 3D COP-SPE method provides a promising approach to selectively extract trace amounts of CAP, TAP, and FF in environmental water samples in ng quantities.

Selectivity evaluation of extraction systems

Extraction is the most common sample preparation technique prior to chromatographic analysis for samples which are too complex, too dilute, or contain matrix components incompatible with the further use of the separation system or interfere in the detection step. The most important extraction techniques are biphasic systems involving the transfer of target compounds from the sample to a different phase ideally accompanied by no more than a tolerable burden of co-extracted matrix compounds. The solvation parameter model affords a general framework to characterize biphasic extraction systems in terms of their relative capability for solute-phase intermolecular interactions (dispersion, dipole-type, hydrogen bonding) and within phase solvent-solvent interactions for cavity formation (cohesion). The approach is general and allows the comparison of liquid and solid extraction phases using the same terms and is used to explain the features important for the selective enrichment of target compounds by a specific extraction phase using solvent extraction, liquid-liquid extraction, and solid-phase extraction for samples in a gas, liquid, or solid phase. Hierarchical cluster analysis with the system constants of the solvation parameter model as variables facilitates the selection of solvents for extraction, the identification of liquid-liquid distribution systems with non-redundant selectivity, and evaluation of different approaches using liquids and solids for the isolation of target compounds from different matrices.

Advances in solid-phase extraction techniques: Role of nanosorbents for the enrichment of antibiotics for analytical quantification

Antibiotics are life-saving medications for treating bacterial infections; however it has been discovered that resistance developed by bacteria against these incredible agents is the primary contributing factor to rising global mortality rates. The fundamental cause of the emergence of antibiotic resistance in bacteria is the presence of antibiotic residues in various environmental matrices. Although antibiotics are present in diluted form in environmental matrices like water, consistent exposure of bacteria to these minute levels is enough for the resistance to develop. So, identifying these tiny concentrations of numerous antibiotics in various and complicated matrices will be a crucial step in controlling their disposal in those matrices. Solid phase extraction, a popular and customizable extraction technology, was developed according to the aspirations of the researchers. It is a unique alternative technique that could be implemented either alone or in combination with other approaches at different stages because of the multitude of sorbent varieties and techniques. Initially, sorbents are utilized for extraction in their natural state. The basic sorbent has been modified over time with nanoparticles and multilayer sorbents, which have indeed helped to accomplish the desired extraction efficiencies. Among the current traditional extraction techniques such as liquid-liquid extraction, protein precipitation, and salting out techniques, solid-phase extractions (SPE) with nanosorbents are most productive because, they can be automated, selective, and can be integrated with other extraction techniques. This review aims to provide a broad overview of advancements and developments in sorbents with a specific emphasis on the applications of SPE techniques used for antibiotic detection and quantification in various matrices in the last two decades.

Nanographite-assisted matrix solid phase dispersion microextraction of active and toxic compounds from complex food matrices using cyclodextrin aqueous solution as elution solvent

In this study, a cyclodextrin aqueous solution was used as an environmentally friendly eluent to simultaneously extract active and toxic compounds from food matrices with the aid of nanographite-assisted matrix solid phase dispersion microextraction (NG-MSPDM). The NG-MSPDM procedure was optimized by single-factor experiments and response surface methodology to obtain optimum conditions. The proposed method achieved excellent linearity at 0.10-20 μg/mL for all target analytes with a coefficient of correction (R²) ≥ 0.9909, limits of detection < 52.01 ng/mL, satisfactory reproducibility below 3.21 %, and acceptable recoveries of 82.0-112 %. To accurately determine the target components in the complex matrix, collision cross-section values of the analytes were obtained using ion mobility quadrupole time-of-flight mass spectrometry (IM-Q-TOF/MS). Results indicated that the NG-MSPDM method successfully achieved the simultaneous extraction of flavonoids and phenoxyacetic herbicides from Alpinia officinarum.

Determination of methanol-derivatives in drying oils after metal oxide-based dispersive solid phase extraction/QuEChERS clean-up

The determination of secondary volatile degradation products in drying oil extracts is substantial to prevent formation of undesirable metal formates in paintings and/or other artefacts. This study develops a simple, cost-effective, and reliable, high-performance liquid chromatography with diode array detector (HPLC-DAD) method to determine three secondary volatile degradation products (methanol, formaldehyde, and formic acid) in drying oils, including linseed, poppy-seed, and walnut oil. Extraction of analytes was performed using QuEChERS-based procedure followed by metal oxide-based dispersive solid-phase extraction (d-SPE) clean-up and presented a good performance for all of the volatile analytes of interest with recoveries in the range of 90-120% after application of the nanostructured cerium oxide-based (CeO₂) and zirconia-based (ZrO₂) sorbents prepared by favorable and ecological-friendly methods. With a new clean-up solution for samples with high-fat content, it was possible to achieve higher recoveries than with commercial Z-Sep/C18 sorbent. In all cases, relative standard deviations (RSD) of less than 10% were achieved. No significant matrix interference was observed due to the application of effective sorbents in nanostructured form. The developed method was applied to samples of drying oils, and it was found that after storage for three months, all methanol was most likely oxidized to formaldehyde and formic acid. The concentrations of formaldehyde were in the range of 260 - 304 μg∙g^-1, while formic acid concentrations ranged between 72 - 386 μg∙g^-1. The highest concentration of formaldehyde (304 μg∙g^-1) and formic acid (386 μg∙g^-1) was found in linseed oil.

Recent applications of organic molecule-based framework porous materials in solid-phase microextraction for pharmaceutical analysis

Sample preparation is an indispensable part of detection of complex samples in pharmaceutical analysis. Solid-phase microextraction (SPME) has obtained a lot of attention due to its advantages of time saving, less solvent and easily automation. A variety of functional materials are used as sorbents in SPME to carry out selective and high extraction. This review centers around the recent applications of organic molecule-based framework porous materials, such as metal organic frameworks (MOFs) and covalent organic frameworks (COFs), as SPME coating materials mainly focus on pharmaceutical analysis in food, environment, and biological samples. Four representative extraction devices are introduced, including on-fiber SPME, in-tube SPME, thin film SPME, stir bar SPME. The application prospect of other organic porous materials as sorbents for pharmaceutical analysis are also discussed, such as hyper crosslinked polymers (HCPs) and conjugated microporous polymers (CMPs). The progresses and discusses are provided to offer references for further research focusing on application and development of organic molecule-based framework porous materials in the field of SPME.

Determination of polycyclic aromatic hydrocarbons in surface waters by high performance liquid chromatography previous to preconcentration through solid-phase extraction by using polymeric monoliths

A simple, sensitive and reproducible solid-phase extraction method using plastic cartridges containing a monolithic sorbent (m-SPE), coupled to reverse phase liquid chromatography analysis, aiming to determine fifteen polycyclic aromatic hydrocarbons in surface water samples, was developed. The sorbent was easily prepared through a thermal polymerization reaction by using a mixture of n-butyl methacrylate as non-polar monomer and ethylene glycol dimethacrylate as crosslinker contained in a typical Polypropylene syringe cartridge. The effect of different parameters (type of hydrophobic monomer, elution solvent, sample volume, sorbent amount and sorbent load capacity) on the extraction efficiency was optimized. The optimal conditions were achieved by using n-butyl methacrylate as monomer, tetrahydrofurane (THF) as solvent for sorbent cleaning, THF:acetone (1:1) as elution solvent, 25.00 mL of sample volume, 600 µL of the polymerization mixture and 60 µg L^-1 as sample loading capacity. Finally, the sorbent charge capacity, the reusability of the cartridges and the extraction efficiency of the m-SPE monolith, as compared with a typical C8 cartridge, were evaluated. Under the optimized experimental conditions, enrichment factors were between 76 and 103, relative recovery factors from 78 to 103%, accuracy values in the range of 58 to 98%, and inter-batch reproducibility values from between 2 and 10%, were obtained. The limits of detection and quantification were obtained by two different procedures: the signal to noise (S/N) ratios (3 and 10, respectively) and the IUPAC convention. The lowest LOD and LOQ values, obtained with the S/N ratios, were between 0.02 and 1.00 µg L^-1, respectively whereas with the IUPAC convention the values were between 0.07 and 5 µg L^-1. Using this procedure, several PAHs could be detected in the surface water sample taken from a river stream located in La Plata city (Buenos Aires Province, Argentina).

Separation and Enrichment of Selected Polar and Non-Polar Organic Micro-Pollutants—The Dual Nature of Quaternary Ammonium Ionic Liquid

In this study, the dual nature of quaternary ammonium ionic liquid–didecyldimethylammonium perchlorate, [DDA][ClO4], was evaluated. A novel and sensitive in situ ionic liquid dispersive liquid–liquid microextraction method (in situ IL-DLLME) combined with magnetic retrieval (MR) was applied to enrich and separate selected organic micro-pollutants, both polar and non-polar. The magnetic support relied on using unmodified magnetic nanoparticles (MNPs) prepared by the co-precipitation of Fe2+/Fe3+ (Fe3O4). The separation technique was on-lined with high-performance liquid chromatography (HPLC–DAD) verified by inverse gas chromatography. An anion exchanger, NaClO4, was added to form an in situ hydrophobic IL. The fine droplets of [DDA][ClO4], molded in aqueous samples, functioned as an extractant for isolating the studied compounds. Then the carrier MNPs were added to separate the IL from the water matrix. The supernatant-free sample was desorbed in acetonitrile (MeCN) and injected into the HPLC system. The applicability of [DDA][ClO4] as an extraction solvent in the MR in situ IL-DLLME method was checked by the selectivity parameters (Sij∞) at infinite dilution. The detection limit (LOD) ranged from 0.011 to 0.079 µg L−1 for PAHs and from 0.012 to 0.020 µg L−1 for benzophenones. The method showed good linearity with correlation coefficients (r2) ranging from 0.9995 to 0.9999.

Current Role of Mass Spectrometry in the Determination of Pesticide Residues in Food

The extensive use of pesticides represents a risk to human health. Consequently, legal frameworks have been established to ensure food safety, including control programs for pesticide residues. In this context, the performance of analytical methods acquires special relevance. Such methods are expected to be able to determine the largest number of compounds at trace concentration levels in complex food matrices, which represents a great analytical challenge. Technical advances in mass spectrometry (MS) have led to the development of more efficient analytical methods for the determination of pesticides. This review provides an overview of current analytical strategies applied in pesticide analysis, with a special focus on MS methods. Current targeted MS methods allow the simultaneous determination of hundreds of pesticides, whereas non-targeted MS methods are now applicable to the identification of pesticide metabolites and transformation products. New trends in pesticide analysis are also presented, including approaches for the simultaneous determination of pesticide residues and other food contaminants (i.e., mega-methods), or the recent application of techniques such as ion mobility–mass spectrometry (IM–MS) for this purpose.

Molecular Dynamic Study of Mechanism Underlying Nature of Molecular Recognition and the Role of Crosslinker in the Synthesis of Salmeterol-Targeting Molecularly Imprinted Polymer for Analysis of Salmeterol Xinafoate in Biological Fluid

The rational preparation of molecularly imprinted polymers (MIPs) in order to have selective extraction of salmeterol xinafoate (SLX) from serum was studied. SLX is an acting β-adrenergic receptor agonist used in the treatment of asthma and has an athletic performance-enhancing effect. Molecular dynamics were used for the simulation of the SLX-imprinted pre-polymerization system, to determine the stability of the system. The computational simulation showed that SLX as a template, 4-hydroxyethyl methacrylate (HEMA) as a monomer, and trimethylolpropane trimethacrylate (TRIM) as a crosslinker in mol ratio of 1:6:20 had the strongest interaction in terms of the radial distribution functional. To validate the computational result, four polymers were synthesized using the precipitation polymerization method, and MIP with composition and ratio corresponding with the system with the strongest interaction as an MD simulation result showed the best performance, with a recovery of 96.59 ± 2.24% of SLX in spiked serum and 92.25 ± 1.12% when SLX was spiked with another analogue structure. Compared with the standard solid phase extraction sorbent C-18, which had a recovery of 79.11 ± 2.96%, the MIP showed better performance. The harmony between the simulation and experimental results illustrates that the molecular dynamic simulations had a significant role in the study and development of the MIPs for analysis of SLX in biological fluid.

Dual-Template Magnetic Molecularly Imprinted Polymer for Simultaneous Determination of Spot Urine Metanephrines and 3-Methoxytyramine for the Diagnosis of Pheochromocytomas and Paragangliomas

A novel dual-template magnetic molecularly imprinted polymer (MMIP) was synthesized to extract normetanephrine (NMN), metanephrine (MN) and 3-methoxytyramine (3-MT) from spot urine samples. As the adsorbent of dispersive solid-phase extraction (d-SPE), the MMIP was prepared using dopamine and MN as dual templates, methacrylic acid as the functional monomer, ethylene glycol dimethacrylate as the crosslinking reagent and magnetic nanoparticles as the magnetic core. NMN, MN, 3-MT and creatinine (Cr) in spot urine samples were selectively enriched by d-SPE and detected by HPLC-fluorescence detection/ultraviolet detection. The peak area (A) ratios of NMN, MN and 3-MT to Cr were used for the diagnosis of pheochromocytomas and paragangliomas (PPGLs). The results showed that the adsorption efficiencies of MMIP for target analytes were all higher than 89.0%, and the coefficient variation precisions of intra-assay and inter-assay for the analytes were within 4.9% and 6.3%, respectively. The recoveries of the analytes were from 93.2% to 112.8%. The MMIP was still functional within 14 days and could be reused at least seven times. The d-SPE and recommended solid-phase extraction (SPE) were both used to pretreat spot urine samples from 18 PPGLs patients and 22 healthy controls. The correlation coefficients of A_NMN/A_Cr and A_MN/A_Cr between d-SPE and SPE were both higher than 0.95. In addition, the areas under the receiver operator curves for spot urine A_NMN/A_Cr, A_MN/A_Cr and plasma free NMN and MN were 0.975, 0.773 and 0.990, 0.821, respectively, indicating the two methods had the similar performances. The d-SPE method took only 20 min, which was effective in clinical application.

Nanomaterials with Excellent Adsorption Characteristics for Sample Pretreatment: A Review

Sample pretreatment in analytical chemistry is critical, and the selection of materials for sample pretreatment is a key factor for high enrichment ability, good practicality, and satisfactory recoveries. In this review, the recent progress of the sample pretreatment methods based on various nanomaterials (i.e., carbon nanomaterials, porous nanomaterials, and magnetic nanomaterials) with excellent adsorption efficiency, selectivity, and reproducibility, as well as their applications, are presented. Due to the unique nanoscale physical–chemical properties, magnetic nanomaterials have been used for the extraction of target analytes by easy-to-handle magnetic separation under a magnetic field, which can avoid cumbersome centrifugation and filtration steps. This review also highlights the preparation process and reaction mechanism of nanomaterials used in the sample pretreatment methods, which have been applied for the extraction organophosphorus pesticides, fluoroquinolone antibiotics, phenoxy carboxylic acids, tetracycline antibiotics, hazardous metal ions, and rosmarinic acid. In addition, the remaining challenges and future directions for nanomaterials used as sorbents in the sample pretreatment are discussed.

Clinical Application Study of Polymeric Nanospheres Network in Methylphenidate Extraction from Urine Samples by Dispersive Solid Phase Extraction Adsorbent

Purpose: This research introduces a polymeric nanosphere as a new dispersive solid phase extraction (DSPE) adsorbent for the extraction of methylphenidate (MPH) from urine and its high performance liquid chromatography (HPLC) analysis. Methods: Polymeric nanosphere is a kind of copolymeric network obtained by copolymerization of an ionic liquid monomer and styrene in the presence of vinyltriethoxysilane and 2-hydroxyethylmethacrylate. HPLC coupled with ultra violet detector was applied for the determination and quantification of MPH. Dominant parameters in extraction were modified by the one-parameter-at-a-time method. The results are as follow: 10 mg of polymeric nanospheres (PNS), 400 μL of acetonitrile (ACT), 5 mL of urine with the pH value of 9, and the extraction and desorption times of 2 and 5 minutes, respectively, which can be selected as the optimum extraction conditions. Results: Calibration curve was plotted through optimized conditions, and the proposed method was validated. The results demonstrated that the method presented linearity in the concentration range of 30-1200 ng/mL. Selectivity, matrix effect and metabolites interference effect were investigated and the method presented no obvious interference effect during the analysis run time. Repeatability, limit of detection (LOD) and limit of quantification (LOQ) values of the method can be reported in this section as well. The method showed satisfactory results with 98.8% relative recovery in the analysis of positive urine samples. Conclusion: The findings convinced the applicability of the introduced method for DSPE and HPLC analysis of the positive urine samples in different laboratories.

Chromatographic techniques for the analysis of organophosphate pesticides with their extraction approach: a review (2015-2020)

In agriculture, a wide range of OPPs has been employed to boost crop yield, quality, and storage life. However, due to the ever-increasing population and rapid urbanization, pesticide use has surged in recent years. These compounds are exceedingly poisonous to humans, and despite the fact that specific legislation prohibits their use, the frequency of toxic and/or fatal incidents, as well as current statistics, suggest that they are currently accessible. As a result, determining the exposure to these substances as well as their detection (and that of their metabolites) in different types of exposed samples has become a hot issue in terms of quality and safety concerns. However, developing tools for the evaluation of these substances is a critical challenge for laboratories. Various chromatographic-based methods reported in the period of 2015-2020 have been developed, which are summarized and critically reviewed in this article, including the extraction of the target OPPs from different kinds of matrices. A comparison among the extraction and analysis techniques has been made in the current review article.

Self-supported 3D reduced graphene oxide for solid-phase extraction: An efficient and low-cost sorbent for environmental contaminants in aqueous solution

A 3D reduced graphene oxide (3D-rGO), a self-supported, efficient, and low-cost sorbent, was synthesised and employed in a solid-phase extraction (SPE) cartridge. As a proof of concept, it was applied to remove diclofenac from aqueous solution. After applying statistical methods to systematically investigate key parameters for optimizing the 3D-rGO cartridge performance, it reached removal and elution efficiencies of 100 % and 90 %, respectively. This SPE cartridge presented advantages compared to traditional ones as the smaller amount of material into the cartridge (mass twenty times smaller), in addition to the ability of eliminating sorbent preconditioning, reducing the use of solvents, and making the process environmentally friendly with a faster operation. Also, it presented improved reproducibility after several cycles of reuse, and finally a lower cost of production unveiled by a cost-benefit analysis. Analysis with scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectrometry, Raman, and Fourier transform infrared spectroscopy in attenuated total reflectance mode suggested that the 3D framework morphology with a high content of carbon at the surface and some residual oxygen-containing groups are the protagonists in this performance. Therefore, 3D-rGO has the potential to be a highly efficient sorbent in analytical procedures using SPE for environmental contaminants in water and effluent samples.

Functional Hybrid Micro/Nanoentities Promote Agro-Food Safety Inspection

The rapid development of nanomaterials has provided a good theoretical basis and technical support to solve the problems of food safety inspection. The combination of functionalized composite nanomaterials and well-known detection methods is gradually applied to detect hazardous substances, such as chemical residues and toxins, in agricultural food products. This review concentrates on the latest agro-food safety inspection techniques and methodologies constructed with the assistance of new hybrid micro/nanoentities, such as molecular imprinting polymers integrated with quantum dots (MIPs@QDs), molecular imprinting polymers integrated with upconversion luminescent nanoparticles (MIPs@UCNPs), upconversion luminescent nanoparticles combined with metal-organic frameworks (UCNPs@MOFs), magnetic metal-organic frameworks (MOFs@Fe₃O₄), magnetic covalent-organic frameworks (Fe₃O₄@COFs), covalent-organic frameworks doped with quantum dots (COFs@QDs), nanobody-involved immunoassay for fast inspection, etc. The presented summary and discussion favor a relevant outlook for further integrating various disciplines, like material science, nanotechnology, and analytical methodology, for addressing new challenges that emerge in agro-food research fields.

Performance comparison between solid phase extraction and magnetic carbon nanotubes facilitated dispersive-micro solid phase extractions (Mag-CNTs/d-µSPE) of a cyanide metabolite in biological samples using GC–MS

Dispersive-micro solid phase extraction (d-µSPE) has gained increasing attention due to its convenience, effectiveness, and flexibility for sorbent selection. Among a various selection of materials, magnetic carbon nanotubes (Mag-CNTs) is a promising d-µSPE sorbent with excellent separation efficiency in addition to its high surface area and adsorption capability. In this work, two different surface-modified Mag-CNTs, Mag-CNTs-COOH and Mag-CNTs-SO3H, were developed to facilitate d-µSPE (Mag-CNTs/d-µSPE). The cyanide metabolite, 2-aminothiazoline-4-carboxylic acid (ATCA), was selected to evaluate their extraction performance using gas chromatography–mass spectrometry (GC–MS) analysis. The Mag-CNTs-COOH enabled a one-step derivatization/desorption approach in the workflow; therefore, a better overall performance was achieved. Compared to the Mag-CNTs-SO3H/d-µSPE and SPE workflow, the one-step desorption/derivatization approach improved the overall extraction efficiency and reduced solvent consumption and waste production. Both Mag-CNTs/d-µSPE workflows were validated according to ANSI/ASB 036 guidelines and showed excellent analytical performances. The limit of detection (LOD) and limit of quantitation (LOQ) of ATCA in synthetic urine were 5 and 10 ng/mL, respectively, and that in bovine blood were achieved at 10 and 60 ng/mL. The SPE method’s LOD and LOQ were also determined at 1 and 25 ng/mL in bovine blood samples. The Mag-CNTs/d-µSPE methods demonstrated great potential to extract polar and ionic metabolites from biological matrices. The extraction processes of ATCA described in this work can provide an easier-to-adopt procedure for potential routine forensic testing of the stable biomarker in cyanide poisoning cases, particularly for those cases where the cyanide detection window has passed.

Near-infrared light responsive dendrimers facilitate the extraction of bicalutamide from human plasma and urine

BACKGROUND

Today, it is well accepted that the quantitative measurement of anti-cancer drugs in human biological samples requires the development and validation of efficient bioanalytical methods. This study attempts to provide a high-capacity and thermo-sensitive nano-adsorbent for bicalutamide extraction from human biological fluids.

MAIN METHODS AND MAJOR RESULTS

In this study, five generations of thermo-sensitive dendrimers were synthesized onto the surface of WS₂ nano-sheets. After drug-loading process from body fluids, the near-infrared (NIR) light (at 808 nm) was applied and light-to-heat conversion by the WS₂ nano-sheets led to shrinkage in polymer chains, resulting the release of the entrapped drug. Finally, the extracted drug was analyzed via HPLC-UV system (at 270 nm). The final nano-adsorbent was described via FE-SEM, XRD, FT-IR, and TGA techniques. The adsorption isotherm data were well fitted by Langmuier isotherm model (R²  = 0.9978). The mean recoveries for spiking bicalutamide at three different concentrations in plasma and urine samples were 92.12% and 94.54% under the NIR light irradiation.

CONCLUSIONS AND IMPLICATIONS

We have developed a smart strategy to analyze bicalutamide in biological samples using near-infrared light irradiation in a controlled manner. All the results indicate the promising application of the proposed method for the extraction and determination of bicalutamide.

Recent developments in sample preparation techniques combined with high-performance liquid chromatography: A critical review

This review article compares and contrasts sample preparation techniques coupled with high-performance liquid chromatography (HPLC) and describes applications developed in biomedical, forensics, and environmental/industrial hygiene in the last two decades. The proper sample preparation technique can offer valued data for a targeted application when coupled to HPLC and a suitable detector. Improvements in sample preparation techniques in the last two decades have resulted in efficient extraction, cleanup, and preconcentration in a single step, thus providing a pathway to tackle complex matrix applications. Applications such as biological therapeutics, proteomics, lipidomics, metabolomics, environmental/industrial hygiene, forensics, glycan cleanup, etc., have been significantly enhanced due to improved sample preparation techniques. This review looks at the early sample preparation techniques. Further, it describes eight sample preparation technique coupled to HPLC that has gained prominence in the last two decades. They are (1) solid-phase extraction (SPE), (2) liquid-liquid extraction (LLE), (3) gel permeation chromatography (GPC), (4) Quick Easy Cheap Effective Rugged, Safe (QuEChERS), (5) solid-phase microextraction (SPME), (6) ultrasonic-assisted solvent extraction (UASE), and (7) microwave-assisted solvent extraction (MWASE). SPE, LLE, GPC, QuEChERS, and SPME can be used offline and online with HPLC. UASE and MWASE can be used offline with HPLC but have also been combined with the online automated techniques of SPE, LLE, GPC, or QuEChERS for targeted analysis. Three application areas of biomedical, forensics, and environmental/industrial hygiene are reviewed for the eight sample preparation techniques. Three hundred and twenty references on the eight sample preparation techniques published over the last two decades (2001-2021) are provided. Other older references were included to illustrate the historical development of sample preparation techniques.

An Update on Molecularly Imprinted Polymer Design through a Computational Approach to Produce Molecular Recognition Material with Enhanced Analytical Performance

Molecularly imprinted polymer (MIP) computational design is expected to become a routine technique prior to synthesis to produce polymers with high affinity and selectivity towards target molecules. Furthermore, using these simulations reduces the cost of optimizing polymerization composition. There are several computational methods used in MIP fabrication and each requires a comprehensive study in order to select a process with results that are most similar to properties exhibited by polymers synthesized through laboratory experiments. Until now, no review has linked computational strategies with experimental results, which are needed to determine the method that is most appropriate for use in designing MIP with high molecular recognition. This review will present an update of the computational approaches started from 2016 until now on quantum mechanics, molecular mechanics and molecular dynamics that have been widely used. It will also discuss the linear correlation between computational results and the polymer performance tests through laboratory experiments to examine to what extent these methods can be relied upon to obtain polymers with high molecular recognition. Based on the literature search, density functional theory (DFT) with various hybrid functions and basis sets is most often used as a theoretical method to provide a shorter MIP manufacturing process as well as good analytical performance as recognition material.

Functionalized graphene oxide tablets for sample preparation of drugs in biological fluids: Extraction of ritonavir, a HIV protease inhibitor, from human saliva and plasma using LC-MS/MS

In this work, graphene oxide-based tablets (GO-Tabs) were prepared by applying a thin layer of functionalized GO on a polyethylene substrate. The GO was functionalized with amine groups (-NH₂ ) by poly(ethylene glycol)bis(3-aminopropyl) terminated (GO-NH₂ -PEG-NH₂ ). The functionalized GO-Tabs were used for the extraction of ritonavir (RTV) in human saliva samples. RTV in plasma and saliva samples was analyzed using LC-MS/MS. Gradient LC system with MS/MS in the positive-ion mode [electrospray ionization (ESI+)] was used. The transitions m/z 721 → 269.0 and m/z 614 → 421 were used for RTV and the internal standard indinavir, respectively. This study determined the human immunodeficiency virus protease inhibitor RTV in human saliva samples using functionalized GO-Tab and LC-MS/MS, and the method was validated. The standard calibration curve for plasma and saliva samples was constructed from 5.0 to 2000 nmol L^-1 . The limit of detection was 0.1 nmol L^-1 , and the limit of quantification was 5.0 nmol L^-1 in both plasma and saliva matrices. The intra- and inter-assay precision values were found to be between 1.5 and 5.8%, and the accuracy values ranged from 88.0 to 108% utilizing saliva and plasma samples. The extraction recovery was more than 80%, and the presented functionalized GO-Tabs could be reused for more than 10 extractions without deterioration in recovery.

Optimising factors affecting solid phase extraction performances of molecular imprinted polymer as recent sample preparation technique

Molecular imprinted solid-phase extraction is the technique that uses molecular imprinted polymer as the sorbent in solid phase extraction. Molecular imprinted solid-phase extraction is effective and efficient for the extraction process and cleaning as compared with solid phase extraction (SPE) without molecular imprinted polymer. The complexity of variables in molecular imprinted solid-phase extraction arise as problems in the analysis, therefore it is necessary to optimize the extraction conditions of molecular imprinted solid-phase extraction. To achieve the sorption equilibrium and achieve the shortest time, certain parameters such as contact time, ion strength of sample, pH of sample, amount of sorbent, sample flow rate, addition of salt and buffer solution, washing solvent, elution solvent, and loading solvent need to be optimized. The selection of suitable properties and quantities of each factor greatly affect the formation of appropriate interactions between the sorbent and analytes. Percentage recovery is also influenced by formation of the appropriate bonds, sample flow rates, extraction time, salt addition, and sorbent mass. Therefore, in the future, molecular imprinted solid-phase extraction optimization has to consider and adjust various factors reviewed in this paper to form appropriate interactions between the absorbent and target molecules which have an impact on the optimal results.

Overview of Sample Preparation and Chromatographic Methods to Analysis Pharmaceutical Active Compounds in Waters Matrices

In the environment, pharmaceutical residues are a field of particular interest due to the adverse effects to either human health or aquatic and soil environment. Because of the diversity of these compounds, at least 3000 substances were identified and categorized into 49 different therapeutic classes, and several actions are urgently required at multiple steps, the main ones: (i) occurrence studies of pharmaceutical active compounds (PhACs) in the water cycle; (ii) the analysis of the potential impact of their introduction into the aquatic environment; (iii) the removal/degradation of the pharmaceutical compounds; and, (iv) the development of more sensible and selective analytical methods to their monitorization. This review aims to present the current state-of-the-art sample preparation methods and chromatographic analysis applied to the study of PhACs in water matrices by pinpointing their advantages and drawbacks. Because it is almost impossible to be comprehensive in all PhACs, instruments, extraction techniques, and applications, this overview focuses on works that were published in the last ten years, mainly those applicable to water matrices.