Axial super-resolution in ultrasound imaging with application to non-destructive evaluation

High-Resolution Ultrasound Platform for Infant Meningitis Detection: An In Vitro Demonstration

Infant meningitis remains a severe burden on global health, particularly for young infants. Traditional ultrasound imaging techniques are limited in spatial resolution to visualize white blood cells (WBCs) in the cerebrospinal fluid (CSF), which is considered a well-established marker for meningitis detection. This work presents a novel platform that uses high-resolution ultrasound to detect the backscatter signals from microscopic CSF WBCs through the anterior fontanelle of neonates and young infants. The whole system was built around a custom probe that allows for a 20 MHz focused transducer to be mechanically controlled to map the area of interest in the CSF. Data processing can be performed internally in the device without the need to extract the images for further analysis. The in vitro feasibility of the proposed solution was evaluated in imaging 7 μm particle suspensions at different concentrations relevant to meningitis diagnosis ranging from 7- to 646-particles (pp)/μL. The experimental tests were conducted from a simple setup using a sample container to a more realistic setup based on an anatomical phantom of the neonatal head. The results show high-quality images, where 7 μm particles can be resolved for the different concentrations.

Investigating the flexural behavior of nanomodified multi-delaminated composites using acoustic emission technique

The formation of multiple delaminations is a frequently observed damage mechanism in composite materials, exerting a more pronounced influence on their strength properties compared to single delaminations. To tackle this issue, the incorporation of nanoparticles has been investigated as a means to enhance composite materials. This study aims to examine the effects of nano-additives, specifically carbon nanotubes and nanosilica, on the flexural behavior of glass/epoxy composites containing multiple embedded delaminations. The acoustic emission technique is employed to gain deeper insights into the damage mechanisms associated with flexural failure. Artificial delaminations of varying sizes, arranged in a triangular pattern, were introduced into four interlayers of a [(0/90)2]s oriented glass/epoxy composite. The findings reveal a notable reduction in flexural properties due to the presence of multiple delaminations. However, the addition of nanoparticles demonstrates a significant improvement in the flexural behavior of the multi-delaminated specimens. The most substantial enhancement is observed in the composite incorporating 0.3 wt% nanosilica + 0.5 wt% carbon nanotubes. Furthermore, genetic K-means and hierarchical clustering techniques are employed to classify different damage mechanisms based on the peak frequency and amplitude of the acoustic emission signals. The results indicate that the hierarchical clustering method outperforms the genetic K-means method in accurately clustering the acoustic emission signals. Moreover, the incorporation of nanoparticles' impact on the occurrence of distinct damage mechanisms is evaluated through the analysis of acoustic signals using Wavelet Packet Transform. By investigating the flexural behavior of nanomodified multi-delaminated composites and employing the acoustic emission technique, this study offers valuable insights into the role of nanoparticles in enhancing the mechanical properties and monitoring the damage mechanisms of composite materials.

Improving axial resolution based on the deconvolution recovery method combined with adaptive weighting techniques for ultrasound imaging

BACKGROUND

A fundamental challenge in medical ultrasound imaging is to improve the resolution accurately. Adaptive beamforming is often used to improve lateral resolution, such as minimum variance (MV) and phase coherence factor (PCF). However, it is difficult to improve the axial resolution due to the limitation of the spatial pulse length (SPL) of the transmitted signal.

OBJECTIVE

A deconvolution recovery method combines two adaptive weighting techniques to improve axial resolution.

METHODS

A deconvolution recovery (DR) technique is used to improve axial resolution with a shorter SPL. Then, the DR is combined with MV and PCF (DR-MVPCF) to suppress the sidelobe. The influence of different transmission modes, regularization parameters, and the estimation of point spread function are discussed on the proposed algorithm.

RESULTS

In simulation, DR-MVPCF improved axial resolution from 0.41 mm (0.98 λ) to 0.09 mm (0.21 λ) compared with MV-PCF. In the water bath experiment, DR-MVPCF provided improvement of axial resolution from 0.39 mm (0.93 λ) to 0.07 mm (0.17 λ) compared with MV-PCF. In-vivo data experiment, the DR-MVPCF method increased the speckle signal-to-noise ratio and visibility of the structure while the contrast ratio and contrast-noise ratio decreased.

CONCLUSIONS

The proposed method can improve the axial resolution significantly.

Ultrasonic array imaging of highly attenuative materials with spatio-temporal singular value decomposition

With the increasing use of high density polyethylene (HDPE) pipes in nuclear industry which puts safety at the forefront, ultrasonic array imaging methods play a vital role in the structural integrity of HDPE pipe materials. However, the viscoelastic attenuation of HDPE pipe materials significantly decreases the level of signals, leading to a low signal-to-noise ratio caused by electronic noise. In this work, a domain-adapted spatio-temporal singular value decomposition (STSVD) processing algorithm combined with the total focusing method is proposed to improve the ultrasonic array image quality. First, the real-valued radio frequency (RF) data or A-scan signals are demodulated into the complex analytic signals containing in-phase and quadrature (I/Q) components. Then, the STSVD processing algorithm is used to filter the I/Q data, and the filtered I/Q data is converted into RF signals. Finally, the total focusing method is applied to the processed RF signals to produce the image of the region under detection as a stage of post-processing. Experiments are carried out with an ultrasonic linear phased array in contact with the HDPE pipe materials containing multiple side-drilled holes and through-wall notches. Results show that the proposed method can produce images with high quality to provide good inspection and characterization of defects in highly attenuative materials, especially the deeper defects.