Graphene acoustic transducers based on electromagnetic interactions

3D printed triboelectric nanogenerator for underwater ultrasonic sensing

The underwater ultrasound power measurement has become necessary due to the rapid development of sonochemistry and sonocatalysis. This article presents construction of novel triboelectric nanogenerator (TENG) and its application for a detection of ultrasonic waves in water. The device was 3D printed using widely available and cost-effective materials. TENG consisted of the device housing and movable polymer pellets confined between flat electrodes. The device housing and pellets were 3D printed via stereolithography (SLA) and fused deposition modelling (FDM) methods, respectively. The pellets moved periodically driven by the ultrasonic waves leading to generation of an alternating voltage signal. The electric response of TENG was calibrated using a commercially available ultrasonic power sensor. The open-circuit voltage output of TENG was registered in different sections of the ultrasonic bath in order to determine the distribution of the acoustic power. TENG electric responses were analyzed by applying the fast Fourier transform (FFT) and fitting the theoretical dependence to experimental data. The main peaks in the frequency spectra of the voltage waveforms corresponded to the fundamental excitation frequency of the ultrasonic bath. TENG device, presented in this paper, can be successfully applied as a self-powered sensor for detection of ultrasonic waves. It enables precise control of the sonochemical process and reduction of power losses of the ultrasonic reactor. 3D printing technology has been confirmed to be fast, easy, and scalable method of fabrication of the ultrasonic sensors.

Experimental investigation on characteristics of graphene acoustic transducers driven by electrostatic and electromagnetic forces

Acoustic transducers with graphene film have high sensitivity and wide bandwidth of frequency response as receivers. However, they exist in transmitting mode with low radiation performance. We propose an effective approach to enhance radiation performance of the graphene acoustic transducer by embedding a coil in insulating layer, and investigate the characteristics of graphene acoustic transducers by experiments. A graphene acoustic transducer is designed and fabricated. The highest receiving sensitivity of the transducer is -30 dB. The output sound pressure level of the transducer is more than 3 dB on average in the range of 2 ∼ 16 kHz compared without a coil. And the sound pressure level increases by 6 dB on average in the range of 40 ∼ 45 kHz. These results demonstrate that the graphene transducer maintains high receiving performance, and also improves acoustic radiation performance, which greatly expands its application field.

AZ31B magnesium alloy matching layer for Lens-focused piezoelectric transducer application

Compared with planar transducers, focused transducers have higher ultrasound intensity and better lateral resolution in the focal zone. At present, the matching layer materials for focused transducers are mainly 0-3 composite materials, which have problems such as non-uniformity, difficulty to fabricate at high frequencies, and large sound attenuation. In this paper, finite element analysis is carried out to simulate lens-focused transducers with different matching layer structures and materials. It is found that the focused transducer with magnesium alloy matching layer has the best comprehensive performance. A lens-focused PZT-5H ultrasonic transducer was then fabricated with AZ31B magnesium alloy as the first matching layer. The measured results show that the center frequency of the transducer is 4.38 MHz, the -6-dB bandwidth is 68.35 % and the insertion loss is -13.88 dB. Benefiting from the high uniformity, high acoustic impedance and extremely low acoustic attenuation of magnesium alloy, the transducers in this research exhibit superior performances than other reported transducers with conventional matching layer. The current work suggests that AZ31B magnesium alloy is a promising matching layer material for ultrasonic transducers.

The effect of copper grain size on laser ultrasonic backscattered signal

Grain size has an essential influence on the serviceability of metallic materials. In this paper, a noncontact laser ultrasonic testing platform is built to study the effect of copper grain size on the laser ultrasonic backscattered signal. According to the correlation between grain size and ultrasonic wavelength, the ultrasonic scattering by copper grains in the experiment contains not only Rayleigh scattering but also the transition region from Rayleigh scattering to stochastic scattering. Using time-frequency analysis, the influence of copper grain size on the characteristic parameters of backscattering was explored, and a prediction model of grain size was established, which was compared with the prediction model based on the attenuation method to verify the accuracy of the backscattering model. The results show that the backscattered signal can adequately characterize the grain size information and laser ultrasonics is a method that can realize on-line detection of grain size.