Structural features of hydroxyapatite and carbonated apatite formed under the influence of ultrasound and microwave radiation and their effect on the bioactivity of the nanomaterials

Effect of zinc oxide micro- and nanoparticles on cytotoxicity, antimicrobial activity and mechanical properties of apatite-polymer osteoplastic material

This work is devoted to the comparison of the physical and biological properties of synthesized osteoplastic composites with an experimentally determined content (375 μg/g) of the micro (ZnOMPs) and nano (ZnONPs) particles, immobilized in Hydroxyapatite-Alginate-Chitosan matrix (HA-Alg-CS). ZnONPs show pronounced antimicrobial activity against E.coli ATCC 25922 and S. aureus ATCC 25923, while ZnOMPs only in the CS presence. Composites containing ZnONPs/MPs do not have a toxic effect on bone-forming cells - osteoblasts, preserving their ability to biomineralization. ZnOMPs and ZnONPs to varying degrees, but significantly affect composites' swelling, porosity, shape stability, and prolong vitamin D3 release for 120h, compared to Control. Composites do not demonstrate unwanted "burst release." ZnONPs/MPs increase Youngs' modulus of the HA-Alg matrix, namely 348 → 419 MPa (ZnOMPs), 348 → 646 MPa (ZnONPs), and weaken the plastic (irreversible) deformations. The compressive strength of HA-Alg and HA-Alg/CS matrixes containing ZnONPs (178 MPa and 251 MPa, respectively) is in the range of values for native cortical bone (170-193 MPa). Biocompatibility and lack of toxic effect give both composites a perspective for osteoplastic application, but composites doped with ZnONPs are more attractive.

Source separation of human excreta: Effect on resource recovery via pyrolysis

More people globally are now using on-site sanitation technologies than sewered connections. The management of faecal sludge generated by on-site facilities is still challenging and requires an understanding of all sanitation service chain components and their interactions; from source conditions to treatment and resource recovery. This study aimed to improve the current lack of knowledge regarding these interactions, by establishing a quantifiable relationship between human excreta source separation and resource recovery via pyrolysis. The effects of source separation of faeces and urine on biochar quality were investigated for different pyrolysis temperatures (450 °C, 550 °C, 650 °C) and this information was used to assess energy and nutrient recovery. Results quantify the benefits of urine diversion for nitrogen recovery (70% of total N losses during thermal treatment avoided) and show an increase in the liming potential of the produced faecal-based biochars. The quality of produced solid fuels is also improved when source-separated faeces (SSF) are used as a feedstock for pyrolysis, including a 50% increase in char calorific value. On the other hand, biochars from mixed urine and faeces (MUF) are more rich in phosphorus and potassium, and surface morphology investigation indicates higher porosity compared to SSF biochars. The high salinity of MUF biochars should be considered before agricultural applications. For both biochar types (SSF, MUF), the presence of phosphate compounds of high fertiliser value was confirmed by X-ray diffraction analysis, and temperatures around 500 °C are recommended to optimise nutrient and carbon behaviour when pyrolysing human excreta. These findings can be used for the design of circular faecal sludge management systems, linking resource recovery objectives to source conditions, and vice-versa. Ultimately, achieving consistent resource recovery from human excreta can act as an incentive for universal access to safe and sustainable sanitation.

An investigation on the fabrication and characterization of friction stir processed nano-HAp reinforced AZ91D magnesium matrix surface composite for bio-implants

In the present research, friction stir processed (FSPed) nano-hydroxyapatite reinforced AZ91D magnesium matrix surface composite has been developed with improved ultimate tensile strength (UTS) and biological performance, which are needed for the bio-implants. Nano-hydroxyapatite reinforcement with varying proportions (5.8%, 8.3%, and 12.5%) was introduced into the AZ91-D parent material (PM) by the grooving method with different grooves of 0.5, 1 & 1.5 mm of width and 2 mm depth machined on the surface of the PM. Taguchi's L-9 orthogonal array was employed to optimize the processing variables for enhancing the UTS of the developed composite material. The optimum parameters were discovered to be the tool rotational speed of 1000 rpm, transverse speed of 50 mm/min, and 12.5% reinforcement concentration. The results revealed that the tool rotational speed contributes the highest effect (43.69%) on UTS, followed by the reinforcement percentage (37.49%) and transverse speed (18.31%). The FSPed samples at the optimized parameter setting confirmed the enhancement of 30.17% and 31.86% in UTS and micro-hardness, respectively, compared to the PM. Cytotoxicity of the optimized sample was also found superior compared to the other FSPed samples. The optimized FSPed composite's grain size was 6.88 times smaller than the AZ91D parent matrix material. The improved mechanical and biological performances of the composites are attributed to the significant grain refinement and proper dispersion of the nHAp reinforcement in the matrix.

Metal ions doping effect on the physicochemical, antimicrobial, and wound healing profiles of alginate-based composite

The alginate (Alg) matrix with immobilized hydroxyapatite (HAp) and zinc oxide (ZnO), cross-linked by chitosan (CS) and metal ions (Meⁿ⁺) Ca²⁺, Zn²⁺, and Cu²⁺ was created as a wound dressing. The effect of Meⁿ⁺ and their concentrations on water vapor transition, fluid handling, dehydration, drug release, and healing are shown. Me-containing samples have a lower sorption capacity, than a commercial Kaltostat, however, a much lower degree of their dehydration provides a longer wound wet. The Meⁿ⁺ presence lowers the environmental pH to slightly acidic values promoting healing. Ca²⁺, Zn²⁺, and Cu²⁺ in complexes with CS increase antimicrobial effect against E. coli and S. aureus, slow down the Anaesthesine release, making it compatible with Fickian diffusion in the Zn²⁺ and Cu²⁺ presence, and non-Fickian transport under Ca²⁺ influence. The material promotes the proliferation of the fibroblasts, an increase of collagen fibres, and new arterial and venous capillaries, indicating the intensity of the healing process.

Calcium Phosphates-Chitosan Composite Layers Obtained by Combining Radio-Frequency Magnetron Sputtering and Matrix-Assisted Pulsed Laser Evaporation Techniques

In this work, we report the synthesis of calcium phosphate-chitosan composite layers. Calcium phosphate layers were deposited on titanium substrates by radio-frequency magnetron sputtering technique by varying the substrate temperature from room temperature (25 °C) up to 100 and 300 °C. Further, chitosan was deposited by matrix-assisted pulsed laser evaporation technique on the calcium phosphate layers. The temperature at the substrate during the deposition process of calcium phosphate layers plays an important role in the embedding of chitosan, as scanning electron microscopy analysis showed. The degree of chitosan incorporation into the calcium phosphate layers significantly influence the physico-chemical properties and the adherence strength of the resulted layers to the substrates. For example, the decreases of Ca/P ratio at the addition of chitosan suggests that a calcium deficient hydroxyapatite structure is formed when the CaP layers are generated on Ti substrates kept at room temperature during the deposition process. The Fourier transform infrared spectroscopy analysis of the samples suggest that the PO₄^3-/CO₃^2- substitution is possible. The X-ray diffraction spectra indicated that the crystalline structure of the calcium phosphate layers obtained at the 300 °C substrate temperature is disturbed by the addition of chitosan. The adherence strength of the composite layers to the titanium substrates is diminished after the chitosan deposition. However, no complete exfoliation of the layers was observed.

Recycling phosphorus and calcium from aquaculture waste as a precursor for hydroxyapatite (HAp) production: a review

Water contaminated with phosphorus needs to be managed efficiently to ensure that clean water sources will be preserved. Aquaculture plays an essential role in supplying food and generating high revenue. However, the quantity of phosphorus released from aquaculture effluents is among the major concerns for the environment. Phosphorus is a non-renewable, spatially concentrated material essential for global food production. Phosphorus is also known as a primary source of eutrophication. Hence, phosphorus recovery and separation from different wastewater streams are mandatory. This paper reviews the source of phosphorus in the environment, focusing on aquaculture wastewater as a precursor for hydroxyapatite formation evaluates the research progress on maximizing phosphorus removal from aquaculture wastewater effluents and converting it into a conversion. Shrimp shell waste appears to be an essential resource for manufacturing high-value chemicals, given current trends in wealth creation from waste. Shrimp shell waste is the richest source of calcium carbonate and has been used to produce hydroxyapatite after proper treatment is reviewed. There have been significant attempts to create safe and long-term solutions for the disposal of shrimp shell debris. Through the discussion, the optimum condition of the method, the source of phosphorus, and the calcium are the factors that influence the formation of hydroxyapatite as a pioneer in zero-waste management for sustainability and profitable approach. This review will provide comprehensive documentation on resource utilization and product development from aquaculture wastewater and waste to achieve a zero-waste approach.

Hydroxyapatite-based adsorbents: Applications in sequestering heavy metals and dyes

Hydroxyapatite (HAp) is a calcium phosphate material that was used primarily in bone regeneration and repair as a result of its chemical similarity with bone. However, HAp has emerged as a very promising adsorbent for sequestering contaminants like heavy metals, dyes, hydrocarbons as well as other emerging pollutants from wastewater as a result of its versatility and encouraging adsorptive properties. Contaminants like heavy metals and dyes have been a major source of environmental concern. Research studies involving the use of HAp as adsorbents for the adsorptive treatment of heavy metal- and dye-contaminated wastewater have become increasingly popular due to its eco-friendliness, easy synthesis, unique adsorption properties etc. Various methods are available for the synthesis of HAp and its composites with some of these methods used in combination with other methods to obtain more efficient HAp-based adsorbents. In this work, the adsorptive removal of heavy metals and dyes by HAp and its composites was extensively reviewed as well as the parametric effects of process factors like contact time, solution pH, temperature, solute concentration etc on the adsorption process. Kinetic, thermodynamic, and isotherm models for elucidating the adsorption process were also considered. Generally, from the works reviewed, HAp-based adsorbents were found to be very effective for sequestering heavy metals and dyes from solution and thus presents a low-cost option for adsorptive wastewater treatment.

3D printed PEEK/HA composites for bone tissue engineering applications: Effect of material formulation on mechanical performance and bioactive potential

Polyetheretherketone (PEEK) is a biocompatible polymer widely used for biomedical applications. Because it is biologically inert, bioactive phases, such as nano-hydroxyapatite (HA), have been added to PEEK in order to improve its bioactivity. 3D printing (3DP) technologies are being increasingly used today to manufacture patient specific devices and implants. However, processing of PEEK is challenging due to its high melting point which is above 340 °C. In this study, PEEK-based filaments containing 10 wt% of pure nano-HA, strontium (Sr)- doped nano-HA and Zinc (Zn)-doped nano-HA were produced via hot-melt extrusion and subsequently 3D printed via fused deposition modelling (FDM), following an initial optimization process. The raw materials, extruded filaments and 3D printed samples were characterized in terms of physicochemical, thermal and morphological analysis. Moreover, the mechanical performance of 3D printed specimens was assessed via tensile tensing. Although an increase in the melting point and a reduction in crystallization temperature was observed with the addition of HA and doped HA to pure PEEK, there was no noticeable increase in the degree of crystallinity. Regarding the mechanical behavior, no significant differences were detected following the addition of the inorganic phases to the polymeric matrix, although a small reduction in the ultimate tensile strength (~14%) and Young's modulus (~5%) in PEEK/HA was observed in comparison to pure PEEK. Moreover, in vitro bioactivity of 3D printed samples was evaluated via a simulated body fluid immersion test for up to 28 days; the formation of apatite was observed on the surfaces of sample surfaces containing HA, SrHA and ZnHA. These results indicate the potential to produce bioactive, 3DP PEEK composites for challenging applications such as in craniofacial bone repair.

New Generation of Hybrid Materials Based on Gelatin and Bioactive Glass Particles for Bone Tissue Regeneration

Hybrid scaffolds based on bioactive glass (BAG) particles (<38 µm), covalently linked to gelatin (G*) using 3-glycidoxypropyltrimethoxysilane (GPTMS), have been studied for bone bioengineering. In this study, two glass compositions (13-93 and 13-93B20 (where 20% of the SiO₂ was replaced with B₂O₃)) were introduced in the gelatin matrix. The C_factor (gelatin/GPTMS molar ratio) was kept constant at 500. The hybrids obtained were found to be stable at 37 °C in solution, the condition in which pure gelatin is liquid. All hybrids were characterized by in vitro dissolution in Tris(hydroxymethyl)aminomethane (TRIS) solution (for up to 4 weeks) and Simulated Body Fluid (SBF) (for up to 2 weeks). Samples processed with 13-93B20 exhibited faster initial dissolution and significantly faster precipitation of a hydroxyapatite (HA) layer. The faster ion release and HA precipitation recorded from the G*/13-93B20 samples are attributable to the higher reactivity of borosilicate compared to silicate glass. The MC3T3-E1 cell behavior in direct contact with the hybrids was investigated, showing that the cells were able to proliferate and spread on the developed biomaterials. Tailoring the glass composition allows us to better control the material’s dissolution, biodegradability, and bioactivity. Bioactive (especially with 13-93B20 BAG) and biocompatible, the hybrids are promising for bone application.

Morphological evolution of carbonated hydroxyapatite to faceted nanorods through intermediate states

On the conversion of a parent calcite nanocrystal, thin low-crystalline nanosheets of carbonated hydroxyapatite are initially grown via the dissolution–reprecipitation route and then evolve into faceted rods covered with stable surfaces.

Microwave-Assisted Fabrication of Mesoporous Silica-Calcium Phosphate Composites for Dental Application

Herein, the microwave-assisted wet precipitation method was used to obtain materials consisting of mesoporous silica (SBA-15) and calcium orthophosphates (CaP). Composites were prepared through immersion of mesoporous silica in different calcification coating solutions and then exposed to microwave radiation. The composites were characterized in terms of molecular structure, crystallinity, morphology, chemical composition, and mineralization potential by Fourier-transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), and scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy (SEM-EDX). The application of microwave irradiation resulted in the formation of different types of calcium orthophosphates such as calcium deficient hydroxyapatite (CDHA), octacalcium phosphate (OCP), and amorphous calcium phosphate (ACP) on the SBA-15 surface, depending on the type of coating solution. The composites for which the progressive formation of hydroxyapatite during incubation in simulated body fluid was observed were further used in the production of final pharmaceutical forms: membranes, granules, and pellets. All of the obtained pharmaceutical forms preserved mineralization properties.

Ultrasonic-assisted recycling of Nile tilapia fish scale biowaste into low-cost nano-hydroxyapatite: Ultrasonic-assisted adsorption for Hg2+ removal from aqueous solution followed by "turn-off" fluorescent sensor based on Hg2+-graphene quantum dots

This study was planned to recycle calcium and the phosphorus-rich Nile tilapia fish scale biowaste into nano-hydroxyapatite (FHAP), using ultrasonic-assisted extraction of calcium and phosphorus from fish scales, which was optimized in term of extraction time, acid concentration, extraction temperature, and ultrasonic power. These two elements were determined simultaneously by inductively coupled plasma atomic emission spectrometry and the FHAP phase was formed upon addition of the extracted element solution in alkaline medium using homogenous precipitation assisted with ultrasound energy. The FHAP adsorbent was characterized by x-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller. A combination of FHAP and the ultrasonic method was then used to remove Hg²⁺ from aqueous solution. Four significant variables affecting Hg²⁺ removal, namely, adsorbent dosage, pH, ultrasonic power, and adsorption time, were studied. The results exhibited that the optimal conditions for maximizing the removal of Hg²⁺ were 0.02 g adsorbent dosage, pH 8, 0.4 kW ultrasonic power, 20 min adsorption time, and 30 °C adsorption temperature. The sorption mechanism of Hg²⁺ was revealed by isotherm modeling, indicating that FHAP adsorbent has a potential for Hg²⁺ removal in aqueous media with the maximum adsorption capacity being 227.27 mg g^-1. This adsorption behavior is in agreement with the Langmuir model as reflected by a satisfactory R² value of 0.9967, when the kinetics data were fitted with pseudo-second-order. Therefore, the FHAP could be an alternative adsorbent for the ultrasonic-assisted removal of Hg²⁺ at very high efficiency and within a very short period of time.

Ultrasound-assisted synthesis of nanocrystallized silicocarnotite biomaterial with improved sinterability and osteogenic activity

It has been proved that silicon-substituted calcium phosphate ceramics possess superior bone regeneration and resorbability to HA, while the synthesis of single-phase nanocrystallized high Si-containing calcium phosphate is still a challenge. In the present work, a novel and facile aqueous precipitation method assisted with ultrasonic irradiation was adopted firstly to synthesise a single-phase nanocrystallized calcium silicophosphate (Ca₅(PO₄)₂SiO₄, CPS) biomaterial. Crystallization and morphology of Si-apatite precursors synthesized with or without ultrasonic assistance were primarily investigated and the related mechanism was discussed. Moreover, the sinterability, in vitro bioactivity and osteogenic activity of the synthesized CPS were studied in detail. Results showed that an ultrasonic cavitation effect could be beneficial to form a highly dispersive CPS precursor with a single Si-apatite phase, which greatly reduced the calcination temperature of CPS from 1350 °C to 1000 °C. Nanocrystallized CPS powders were obtained successfully under ultrasound-assisted conditions, which showed superior sinterability, in vitro bioactivity and osteogenic activity than those of micron-sized CPS and HA powders. It might be a promising candidate material for bone tissue regeneration applications.

Single-walled carbon nanotubes loaded hydroxyapatite-alginate beads with enhanced mechanical properties and sustained drug release ability

Single-walled carbon nanotubes (SWCNTs) containing biomaterial with enhanced mechanical properties for the potential orthopedic application were synthesized and investigated. X-ray diffraction and X-ray fluorescence analysis were indications of the formation of calcium-deficient (Ca/P = 1.65) hydroxyapatite (HA) with a small carbonate content under influence of microwave irradiation. The investigated mechanical properties (maximal relative deformation, compressive strength and Young's modulus) of SWCNT loaded HA-alginate composites confirm their dependence on SWCNTs content. The compressive strength of HA-alginate-SWCNT and the HA-alginate control (202 and 159 MPa, respectively) lies within the values characteristic for the cortical bone. The addition of 0.5% SWCNT, in relation to the content of HA, increases the Young's modulus of the HA-alginate-SWCNT (645 MPa) compared to the SWCNT-free HA-alginate sample (563 MPa), and enhances the material shape stability in simulated physiological conditions. Structural modeling of HA-alginate-SWCNT system showed, that physical adsorption of SWCNT into HA-alginate occurs by forming triple complexes stabilized by solvophobic/van der Waals interactions and H-bonds. The high-performance liquid chromatography demonstrated the influence of SWCNTs on the sustained anaesthesinum drug (used as a model drug) release (456 h against 408 h for SWCNT-free sample). Cell culture assay confirmed biocompatibility and stimulation of osteoblast proliferation of 0.05% and 0.5% SWCNT-containing composites during a 3-day cultivation. All these facts may suggest the potential possibility of using the SWCNT-containing materials, based on HA and alginate, for bone tissue engineering.

Antibacterial Effect of Au Implantation in Ductile Nanocomposite Multilayer (TiAlSiY)N/CrN Coatings

A multilayered nanocomposite designed for biomedical applications based on (TiAlSiY)N/CrN coating implanted by heavy Au^- ions is studied. Ion irradiation produced formation in the upper-surface of local amorphous clusters. The obtained composite system was characterized by SEM-EDS, RBS, SIMS, HRTEM, STEM, and nanoindentation mechanical tests, inspecting microstructure, phase state, elemental composition and surface defectiveness. The range of ion impact with correlation to TRIM simulations amounted to 23.5 nm with visible dislocations and interstitial loops indicating the nanopores' creation up/lengthways to the interface boundary. Mechanical parameters remain stable with a slight decrease (less than 2%) in hardness along with an increase in ductility. The antibacterial effect was evaluated in vitro by agar-diffusion and time-kill (72 h) assessments to define both cell-killing mechanisms: dry surface-contact and cytotoxic golden ions-release into moist environment. The identified antibacterial activity within implantation was 2-2.5 times higher due to inhibition zone diameter and antibacterial rate increase. The Au^- implanted composite exhibits excellent defense against Gram-negative and Gram-positive bacteria without appreciable surface contamination. Possible biophysical and chemical mechanisms of microorganisms' disruption and annihilation were proposed and analyzed. The present study shows that produced composite has large potential for use in biomedical areas.

Calcium phosphate powder synthesis by out-of-phase pulsed sonoelectrochemistry

High aspect ratio calcium phosphate (CaP) nanorods were achieved by out-of-phase pulsed sonoelectrodeposition from electrolytic aqueous bath composed of calcium nitrate, ammonium dihydrogenophosphate and surfactant at pH of 4.9. The nature of CaP phases was determined by powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR) and energy dispersive X-ray spectroscopy (EDX). The results reveal the predominantly presence of calcium deficient hydroxyapatite (CDHA). The transmission electron microscopy (TEM) analyzes highlighted that the nanorods are polycristalline and have an aspect ratio up to 30.

Dissolution, bioactivity and osteogenic properties of composites based on polymer and silicate or borosilicate bioactive glass

Bioactive glass (BAG)/Poly (Lactic Acid) (PLA) composites have great potential for bone tissue engineering. The interest in these materials is to obtain a scaffold with tailorable properties bringing together the advantages of the composites' constituents such as the biodegradability, bioactivity and osteoinduction. The materials studied are PLA/13-93 and PLA/13-93B20 (20% of SiO₂ is replaced with B₂O₃ in the 13-93 composition). To characterize them, they were dissolved in TRIS buffer and Simulated Body Fluid (SBF) in vitro. Over the 10 weeks of immersion in TRIS, the ion release from the composites was constant. Following immersion in SBF for 2 weeks, the hydroxyapatite (HA) layer was found to precipitate at the composites surface. By adding Boron, both these reactions were accelerated, as the borosilicate glass dissolves faster than pure silicate glass alone. Polymer degradation was studied and showed that during immersion, the pure PLA rods maintained their molecular weight whereby the composites decreased with time, but despite this the mechanical properties remained stable for at least 10 weeks. Their ability to induce osteogenic differentiation of myoblastic cells was also demonstrated with cell experiments showing that C2C12 cells were able to proliferate and spread on the composites. The Myosin Heavy Chain and Osteopontin were tracked by immunostaining the cells and showed a suppression of the myosin signal and the presence of osteopontin, when seeded onto the composites. This proves osteoinduction occurred. In studying the mineralization of the cells, it was found that BAG presence conditions the synthesizing of mineral matter in the cells. The results show that these composites have a potential for bone tissue engineering.

Synthesis, characterization, in vitro biocompatibility and antibacterial properties study of nanocomposite materials based on hydroxyapatite-biphasic ZnO micro- and nanoparticles embedded in Alginate matrix

The paper presents the results of studies of biocompatibility and antibacterial properties of multiphase nanocomposite materials based on HA-Alg-ZnO (hydroxyapatite‑sodium alginate-biphasic zinc oxide) and HA-ZnO (hydroxyapatite‑zinc oxide), which were synthesized from the analytically pure calcium nitrate tetrahydrate, ammonium hydrophosphate, hydrous ammonia, zinc nitrate hexahydrate and calcium chloride. The samples' antimicrobial activity assessment was carried out on Gram-negative (E. coli, P. aeruginosa) and Gram-positive bacteria (S. aureus and S. epidermidis) test cultures by the co-incubation and modified "agar diffusion" methods. The murine fibroblast cells were used for the biocompatibility tests and cytotoxicity evaluation. It was shown that synthesized nanocomposite material has a multiphase nanoscale architecture, where ZnO nanocrystals are represented by two lattices: cubic and hexagonal. The possible explanation of ZnO nanocrystals' phase transition is given. At the same time, a partial replacement of Ca²⁺ ions by Zn²⁺ ions in the HA lattice possibly occurs due to processing of composite by US radiation. The replacement was evidenced by the non-stoichiometric Ca/P ratio < 2.16, OPO lines' shifting on FTIR spectrum and TEM analysis. The studied composite demonstrate a pronounced antibacterial activity due to the incorporation of ZnO particles into sodium alginate and moistened powder of hydroxyapatite. Both forms of HA-ZnO (suspension) and HA-Alg-ZnO (beads) are biocompatible. An interpretation of the process of Zn ions' embedding into hydroxyapatite and alginate matrix is given, as well as their influence on the biomimetic composite properties is discussed in details. STATEMENT OF SIGNIFICANCE: A number of studies have shown that Zn effectively inhibits the growth and development of bacteria and yeast fungi. Zinc plays an important role in the creation of new antimicrobial agents, and zinc-doped hydroxyapatite will find further application in biomedicine. In this regard, the phase states of zinc oxide, as well as the processes of calcium replacement by zinc in calcium apatite and in alginate should be explored fully. Nowadays we have lack of information and the study's results about those interactions. The present study provides data of the multiphase morphology, antimicrobial activity, biocompatibility and cytotoxicity of the biomimetic nanostructured composite materials, such as sodium alginate/hydroxyapatite/ZnO based granules and hydroxyapatite/ZnO based hydrogel, and the establishing Zn ions' behavior patterns with another composite components.

S. N. SN, Sagadevan S, Hoque ME, Kulandaivelu R. Advanced lithium substituted hydroxyapatite nanoparticles for antimicrobial and hemolytic studies

In this study, pure hydroxyapatite (HAP) and lithium substituted hydroxyapatite (Li-HAP) nanoparticles were synthesized by a sonochemical synthesis process and investigated for their antimicrobial and hemolytic activities.

Ultrasonic-assisted conversion of limestone into needle-like hydroxyapatite nanoparticles

Needle-like hydroxyapatite nanoparticles were successfully synthesized via a reaction between calcium oxide (CaO) that was obtained from calcined limestone and orthophosphoric acid (H₃PO₄) under ultrasonic irradiation at 25 °C. The reaction systems were exposed to ultrasonic waves of 20 kHz for various times ranging from 0 to 4 h. The initial and final pH values of the mixtures of CaO and H₃PO₄ solution were continuously observed (pH < 4.0) after ultrasonic irradiation. The powder was then dried at 60 °C and calcined at 300 °C for 3 h (3 °C/min). The products were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The results showed that the formation of needle-like hydroxyapatite (HAp) nanoparticles was substantially accelerated compared with the reaction without ultrasonic irradiation. The HAp phase was increasingly visible with longer ultrasonic irradiation time compared with the monetite phase (CaHPO₄). This suggests that ultrasonic waved induced a phase transition from the monetite to HAp phase. A smaller needle-like structure of HAp (diameter ∼ 7.4 nm) with a lower contamination of monetite phase was obtained following sonication for 3 h. This study shows that Thai limestone can used as a starting material for synthesizing needle-like HAp nanoparticles with the aid of ultrasonic methods.

Natural calcium phosphates from fish bones and their potential biomedical applications

The treatment and recovery of bio-wastes have raised considerable attention both from the environmental and economic point of view. Every year, a remarkable amount of fish processing by-products are generated and dumped as waste from all over the world. Fish bones can serve as a raw material for the production of high value-added compounds that can be used in various sectors including agrochemical, biomedical, food and pharmaceutical industries. The calcination of fish bones results in a single phase (hydroxyapatite) or bi-phasic (hydroxyapatite-tricalcium phosphate) bioceramics depending on the processing conditions as well as the content of the fish bones. This review summarizes the literature on the production of hydroxyapatite from fish bones and discusses their potential applications in biomedical field. The effect of processing conditions on the properties of final products including Ca/P ratio, crystal structure, particle shape, particle size and biological properties are presented in the light of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, thermogravimetric-differential thermal analysis, bioactivity and biocompatibility investigations.