Ultrasound-assisted synthesis of NiFe- layered double hydroxides as efficient electrode materials in supercapacitors

Sonochemical synthesis of CoNi layered double hydroxide as a cathode material for assembling high performance hybrid supercapacitor

Fabricating battery-type electrode materials with large specific surface area and mesopores is an efficient method for enhancing the electrochemical performance of supercapacitors. This method may provide more active sites for Faradic reactions and shorten the ion-diffusion paths. In this study, the CoNi layered double hydroxides (LDHs) with the morphology of nanoflowers and nanoflakes were prepared in solutions with pH values of 7.5 (CoNi LDH-7.5) and 8.5 (CoNi LDH-8.5) via a simple sonochemical approach. These CoNi LDHs possessed large specific surface areas and favourable electrochemical properties. The CoNi LDH-7.5 delivered a specific capacity of 740.8C/g at a current density of 1 A/g, surpassing CoNi LDH-8.5 with 668.1C/g. The hybrid supercapacitor (HSC) was assembled with activated carbon as the anode and CoNi LDH as the cathode to assess its practical application potential in the field of electrochemical energy storage. The CoNi LDH-7.5//AC HSC achieved the highest energy density of 35.6 W h kg-1 at a power density of 781.1 W kg-1. In addition, both HSCs exhibited little capacity decay over 5,000 cycles at a high current load of 8 A/g. These electrochemical properties of CoNi LDHs make them promising candidates for battery-type electrode materials. The current sonochemical method is simple and can be applied to the preparation of other LDHs-based electrode materials with favourable electrochemical performance.

Ultrasound-Assisted 1,3-Dipolar Cycloadditions Reaction Utilizing Ni-Mg-Fe LDH: A Green and Sustainable Perspective

Ultrasound-assisted synthesis of novel pyrazoles using Ni-Mg-Fe LDH as a catalyst in cyclopentyl methyl ether (CPME) is introduced. Different LDHs were tested as a catalyst for the synthesis of pyrazoles via a 1,3-dipolar cycloaddition reaction. Among them, Ni-Mg-Fe LDH was the superior catalyst for this reaction. This protocol offered high yields, a short reaction time, and a green solvent, and with the reuse of this catalyst six times with the same activity, it could be regarded as an ecofriendly, greener process. The NiMgFe LDH catalyst with the smallest particle size (29 nm) and largest surface area showed its superior efficacy for the 1,3 dipolar cycloaddition rection and can be successfully used in up to six catalytic cycles with little loss of catalytic activity. A plausible mechanism for this reaction over the Ni-Mg-Fe LDH is proposed.

3D hollow NiCo LDH nanocages anchored on 3D CoO sea urchin-like microspheres: A novel 3D/3D structure for hybrid supercapacitor electrodes

The research on the structure of advanced electrode materials is significant in the field of supercapacitors. Herein, for the first time, we propose a novel 3D/3D composite structure by a multi-step process, in which 3D hollow NiCo LDH nanocages are immobilized on 3D sea urchin-like CoO microspheres. Results show that the 3D CoO acts as an efficient and stable channel for ion diffusion, while the hollow NiCo LDH provides abundant redox-active sites. The calculated results based on density function theory (DFT) show that the CoO@NiCo LDH heterostructure has an enhanced density of states (DOS) near the Fermi level and strong adsorption capacity for OH^-, indicating its excellent electrical conductivity and electrochemical reaction kinetics. As a result, the CoO@NiCo LDH electrode has an areal specific capacity of 4.71C cm^-2 at a current density of 3 mA cm^-2 (440.19C g^-1 at 0.28 A g^-1) and can still maintain 88.76 % of the initial capacitance after 5000 cycles. In addition, the assembled hybrid supercapacitor has an energy density of 5.59 mWh cm^-3 at 39.54 mW cm^-3.

Impact of Nanolayered Material and Nanohybrid Modifications on Their Potential Antibacterial Activity

Due to an escalating increase in multiple antibiotic resistance among bacteria, novel nanomaterials with antimicrobial properties are being developed to prevent infectious diseases caused by bacteria that are common in wastewater and the environment. A series of nanolayered structures and nanohybrids were prepared and modified by several methods including an ultrasonic technique, intercalation reactions of fatty acids, and carbon nanotubes, in addition to creating new phases based on zinc and aluminum. The nanomaterials prepared were used against a group of microorganisms, including E. coli, S. aureus, Klebsiella pneumoniae and Pseudomonas aeruginosa. Experimental results revealed that a nanohybrid based on carbon nanotubes and fatty acids showed significant antimicrobial activity against E. coli, and can be implemented in wastewater treatment. Similar behavior was observed for a nanolayered structure which was prepared using ultrasonic waves. For the other microorganisms, a nanolayered structure combined with carbon nanotubes showed a significant and clear inhibitory effect on S. aureus, Klebsiella pneumoniae and Pseudomonas aeruginosa. It is concluded that the nanolayered structures and nanohybrids, which can be modified at low cost with high productivity, using simple operations and straightforward to use equipment, can be considered good candidates for preventing infectious disease and inhibiting the spread of bacteria, especially those that are commonly found in wastewater and the environment.

Adsorption performance of tetracycline on NiFe layered double hydroxide hollow microspheres synthesized with silica as the template

Tetracycline (TC) has poor degradability and hepatotoxicity which will increase the burden on the aquatic environment when discharged into lakes in large quantities. LDH materials are often used as adsorbents because of their superior surface area and controllability of morphology. Herein, NiFe LDH hollow microspheres (NFHMS) were synthesized by a facile hydrothermal method. The removal of tetracycline by the as-prepared material in an aquatic environment was systematically investigated through comprehensive characterizations. The NFHMS sample presents a larger specific surface area than the two control samples, which contributes to its higher adsorption performance. The adsorption mechanisms of TC on NFHMS is mainly electrostatic adsorption. The fitting results of experimental data coincide well with pseudo-second-order and Weber-Morris models through kinetic simulation. Moreover, the Langmuir model is verified to be more suitable than the Freundlich model in elucidating molecular surface adsorption, and the maximum adsorption capacity of NFHMS obtained from the Langmuir model is 90.9 mg g^-1. Higher temperature is beneficial to improve the adsorption performance, and the adsorption process is spontaneous and endothermic. The initial pH of the solution will affect the adsorption capacity, and the partial neutral condition is more favorable. In addition, NFHMS sample exhibits good stability in cyclic tests. Therefore, NFHMS material is expected to be a very promising adsorbent for treating tetracycline in wastewater.

NiFeMn-Layered Double Hydroxides Linked by Graphene as High-Performance Electrocatalysts for Oxygen Evolution Reaction

Currently, precious metal group materials are known as the efficient and widely used oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) catalysts. The exorbitant prices and scarcity of the precious metals have stimulated scale exploration of alternative non-precious metal catalysts with low-cost and high performance. Layered double hydroxides (LDHs) are a promising precursor to prepare cost-effective and high-performance catalysts because they possess abundant micropores and nitrogen self-doping after pyrolysis, which can accelerate the electron transfer and serve as active sites for efficient OER. Herein, we developed a new highly active NiFeMn-layered double hydroxide (NFM LDH) based electrocatalyst for OER. Through building NFM hydroxide/oxyhydroxide heterojunction and incorporation of conductive graphene, the prepared NFM LDH-based electrocatalyst delivers a low overpotential of 338 mV at current density of 10 mA cm⁻² with a small Tafel slope of 67 mV dec⁻¹, which are superior to those of commercial RuO₂ catalyst for OER. The LDH/OOH heterojunction involves strong interfacial coupling, which modulates the local electronic environment and boosts the kinetics of charge transfer. In addition, the high valence Fe³⁺ and Mn³⁺ species formed after NaOH treatment provide more active sites and promote the Ni²⁺ to higher oxidation states during the O₂ evolution. Moreover, graphene contributes a lot to the reduction of charge transfer resistance. The combining effects have greatly enhanced the catalytic ability for OER, demonstrating that the synthesized NFM LDH/OOH heterojunction with graphene linkage can be practically applied as a high-performance electrocatalyst for oxygen production via water splitting.

Enhanced performance of asymmetric supercapacitor based on NiZn-LDH@NiCoSe2electrode materials

While supercapacitors have been widely studied as the next generation of energy storage devices, to develop active electrode materials for enhancing device performance is still challenging. Herein, we fabricated asymmetric supercapacitors based on NiZn-Layered double hydroxide (LDH) @NiCoSe₂hierarchical nanostructures as electrode materials. The NiZn-LDH@NiCoSe₂composites are deposited on Ni foam by a two-step strategy, in which NiZn-LDH nanosheets were firstly grown on Ni foam by hydrothermal method, and then NiCoSe₂particles were prepared by electrodeposition. Due to the synergistic effect between NiZn-LDH and NiCoSe₂, excellent device performance was achieved. In a three-electrode system, the NiZn-LDH@NiCoSe₂exhibits a specific capacitance of 2980 F g^-1at 1 A g^-1. Furthermore, the asymmetric supercapacitor of NiZn-LDH@NiCoSe₂//activated carbon (AC) device was assembled, which exhibits the energy density of 49.2 Wh kg^-1at the power density of 160 W kg^-1, with the capacity retention rate is 91% after 8000 cycles. The results indicates that NiZn-LDH@NiCoSe₂is a promising candidate as electrode materials for efficient energy storage devices.

Freestanding Binder-Free Electrodes with Nanodisk-Needle-like MnCuCo-LTH and Mn1Fe2S2 Porous Microthorns for High-Performance Quasi-Solid-State Supercapacitors

Transition-metal-based layered triple hydroxides (LTHs) are evolving as potential positrode candidates for high-performance supercapacitors; however, their phase stabilization is still critical. Alongside, the availability of limited negatrodes pushes research toward exploring novel alternatives in order to minimize performance limitation issues in the fabricated supercapacitors. Herein, a facile strategy for stabilizing freestanding MnCuCo-LTH-based positrode possessing intermingled nanodisk-needle-like morphology is reported. Alongside, novel high-surface-area negatrodes based on Mn₁Fe₂S₂ exhibiting porous microthorn-like morphology are also optimized. MnCuCo_LTH and Mn₁Fe₂S₂ exhibit remarkably high specific capacities of ∼494 mAh g^-1 (∼2540 F g^-1) and ∼429 mAh g^-1 (∼1546 F g^-1), respectively, at 1 A g^-1. The fabricated quasi-solid-state supercapacitor equipped with a poly(vinyl alcohol) (PVA)-KOH gel electrolyte displays a high specific capacity of ∼144 mAh g^-1 and a specific capacitance of ∼325 F g^-1 at 1 A g^-1. The ultrahigh energy cum power traits of ∼105 Wh kg^-1 (1 A g^-1) and ∼8370 W kg^-1 (at 10 A g^-1) establish an asymmetric supercapacitor as a high-performance energy storage device. This device shows an appreciably high cycling life with a capacitance retention of ∼93% after 10 000 consecutive cycles, at 10 A g^-1. This approach provides a neoteric foresight for developing high-performance advanced energy storage devices equipped with cheaper and eco-friendly components.

Ultrasonic-assisted hydrothermal synthesis of cobalt oxide/nitrogen-doped graphene oxide hybrid as oxygen reduction reaction catalyst for Al-air battery

A persistent ultrasound-assisted hydrothermal method has been developed to prepare cobalt oxide incorporated nitrogen-doped graphene (Co₃O₄/N-GO) hybrids. The electrochemical behaviors and catalytic activity of the prepared hybrids have been systematically investigated as cathode materials for Al-air battery. The results show that ultrasonication can promote the yield ratio of Co₃O₄ from 63.1% to 70.6%. The prepared Co₃O₄/N-GO hybrid with ultrasonication exhibits better ORR activity over that without ultrasonication. The assembled Al-air battery using the ultrasonicated Co₃O₄/N-GO hybrid exhibited an average working voltage of 1.02 V in 4 M KOH electrolyte at 60 mA∙cm^-2, approximately 60 mV higher than that using hybrid without ultrasonication. This should be attributed to large number density of fine Co₃O₄ particles growing on the dispersed GO sheets under the persistent ultrasonication. The related ultrasonic mechanism has been discussed in details.

Advanced drug delivery applications of layered double hydroxide

Layered double hydroxides (LDHs), also known as anionic clays or hydrotalcite-like compounds, are a class of nanomaterials that attained great attention as a carrier for drug delivery applications. The lamellar structure of this compound exhibits a high surface-to-volume ratio which enables the intercalation of therapeutic agents and releases them at the target site, thereby reducing the adverse effect. Moreover, the intercalated drug can be released in a sustained manner, and hence the frequency of drug administration can be decreased. The co-precipitation, ion exchange, manual grinding, and sol-gel methods are the most employed for their synthesis. The unique properties like the ease of synthesis, low cost, high biocompatibility, and low toxicity render them suitable for biomedical applications. This review presents the advances in the structure, properties, method of preparation, types, functionalization, and drug delivery applications of LDH. Also, this review provides various new conceptual insights that can form the basis for new research questions related to the drug delivery applications of LDH.

Recent innovations in functionalized layered double hydroxides: Fabrication, characterization, and industrial applications

Layered Double Hydroxides (LDHs) are a group of hydrotalcite-like nano-sized materials with cationic layers and exchangeable interlayer anions. The wide range of divalent and trivalent cationic metals and anionic compounds are employed in the synthesis of LDH materials, which have improved their importance among the researchers. Because of their high anion exchange property, memory effect, tunable behavior, bio-friendly, simple preparation, and their affordability, these nano-materials are essentially interested today. Modification of LDHs improves their behaviours to make them appropriate in industrial fields, including biological, adsorbent, mechanical, optical, thermal, electrical fields, etc. This review has critically discussed the structural features, main properties, and also clarified the most important methods of modification and intercalation of LDH nano-materials. Moreover, some novel reported researches related to the successful modification of LDH materials have been characterized and briefly the advantages, disadvantages, and applications are presented in the industrial fields.

Ultrasonication construction of the nano-petal NiCoFe-layered double hydroxide: An excellent water oxidation electrocatalyst

Unlike other preparation methods of NiCoFe-layered double hydroxides, the present study provides a facile ultrasound method for synthesis of the nano-petal NiCoFe-layered double hydroxide (LDH) prepared under intensification frequency of 40 kHz and ultrasonic power of 305 W. The effect of time reaction on the morphology of NiCoFe-LDH was investigated using the Field Emission-Scanning Electron Microscopy images. The results show that time reaction can affect the morphology and it also showed that the optimal time for synthesis of nano-petal NiCoFe-LDH was 60 min. Then, the effect of nano-petal NiCoFe-LDH on oxygen evaluation reaction activity was studied and compared with NiCoFe-LDH-c nano paricles. Also, in order to study the effect of Co²⁺ of nano-petal NiCoFe-LDH at water oxidation, the activity of NiFe-LDH synthesized in the same conditions was investigated. The results show that nano-petal NiCoFe-LDH has low onset potential (0.46 V vs. SCE), overpotential (~227 mV) and Tafel slope (234 mV per decade) in comparison with other NiCoFe-LDH nanoparticles (synthesis using co-precipitation method and ultrasonication method within 30 and 120 min), and NiFe-LDH. Based on the obtained results, the nano-petal NiCoFe-LDH can be as a suitable electrocatalyst with good stability for water oxidation reaction in the present 0.1 M KOH media.

Ultrasound-assisted fabrication of a new nanocomposite electrode of samaria and borazon for high performance supercapacitors

The fabrication of hetero structured materials with supercapacitor applications for industrial use remains a key challenge. This work reports a new supercapacitor material with high capacitance, comprising samaria and borazon (O₃Sm₂/BN) synthesized ultrasonically (40 ± 3 kHz, 200 W). The successful synthesis, probable interfaces between O₃Sm₂ and BN and thermal stability of the nanocomposite were studied by UV-Vis. and FT-IR spectroscopies, X-ray diffraction (XRD) and thermo gravimetric analyses (TGA). The morphology of nanocomposite was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Elemental mapping analysis and energy dispersive X-ray analysis (EDAX) confirmed the elements present in the material. This supercapacitor material shows a maximum discharge capacitance of 414 Fg^-1 at 0.25 Ag^-1 and an exceptional retention of specific capacitance (92.5%) in 5000 cycles. Such nanocomposite with better specific capacitance and charge/discharge rates makes it a right candidate as next generation supercapacitor, which certainly finds applications in various unconventional energy storage devices.

Fabrication of Highly Dispersed Cu-Based Oxides as Desirable NH3-SCR Catalysts via Employing CNTs To Decorate the CuAl-Layered Double Hydroxides

In this study, three kinds of CuAl-LDO/CNT (LDO, layered double oxide) catalysts were prepared by the assembly of CNTs and CuAl-LDH (LDH, layered double hydroxides) as well as subsequently structural topological transformation. The effects of the assembly method on the surface structure property and the DeNO_x performance of the prepared samples were systematically investigated. It was found that three CuAl-LDO/CNT catalysts showed preferable NH₃-SCR catalytic performance compared with CuAl-LDO where the catalyst CuAl-LDO/CNTs(I) exhibited optimum NO_x conversion (>80%) and N₂ selectivity (>90%) within 180-300 °C. Such fine catalytic performance can be attributed to the proper surface acidity and redox ability of the catalyst, which might be correlated with the high dispersion of Cu-based active centers caused by the induced nucleation and effective separation action of LDH by carbon nanotubes. In addition, the outstanding H₂O and SO₂ resistance of the CuAl-LDO/CNTs(I) catalyst was also obtained because of the synergistic effect between CuAl-LDO and CNTs, which could greatly promote the activation and decomposition of ammonium sulfate at lower temperatures.

The NiGa-LDH@NiWO4 nanocomposite as an electrode material for pseudocapacitors

NiGa-LDH@X-NiWO₄ (X: 3, 5 or 10 wt% NiWO₄) nanocomposites were prepared at room temperature under mild conditions.