Liposome destruction by hydrodynamic cavitation in comparison to chemical, physical and mechanical treatments

Preliminary analysis: Effect of a rotary generator of hydrodynamic cavitation on rheology and methane yield of wastewater sludge

Slightly acidic (pH 5.1) waste sludge with 4.7 % Total Solids (TS) was treated on a laboratory scale pined disc rotary generator of hydrodynamic cavitation (PD RGHC). Influence of four rotor discs with different number of cavitation generation units (CGUs) was investigated: 8-pins, 12-pins, 16-pins and 8-prism elements. The effect of hydrodynamic cavitation (HC) was investigated by analyzing rheological properties, surface tension, dewaterability, and particle size distribution. After subjecting the sludge to 30 cavitation passes, the dewatering ability of the sludge significantly decreased, resulting in a more than two-fold increase in Capillary Suction Time (CST). All regimes were successful in disintegrating particles to smaller sizes. A slight increase of sludge surface tension was measured post cavitation. Cavitated samples displayed a zero-shear viscosity, in contrast to the untreated sample, where viscosity noticeably increased as shear stress decreased. HC did not improve methane yield. Statistically significant correlations between physio-chemical properties and apparent viscosity at low shear stress were identified. Although there were no discernible statistical differences in sludge characteristics, some trends are visible among investigated CGU designs and warrant further research.

Microfluidic production, stability and loading of synthetic giant unilamellar vesicles

In advanced drug delivery, versatile liposomal formulations are commonly employed for safer and more accurate therapies. Here we report a method that allows a straightforward production of synthetic monodisperse (~ 100 μm) giant unilamellar vesicles (GUVs) using a microfluidic system. The stability analysis based on the microscopy imaging showed that at ambient conditions the produced GUVs had a half-life of 61 ± 2 h. However, it was observed that ~ 90% of the calcein dye that was loaded into GUVs was transported into a surrounding medium in 24 h, thus indicating that the GUVs may release these small dye molecules without distinguishable membrane disruption. We further demonstrated the feasibility of our method by loading GUVs with larger and very different cargo objects; small soluble fluorescent proteins and larger magnetic microparticles in a suspension. Compared to previously reported microfluidics-based production techniques, the obtained results indicate that our simplified method could be equally harnessed in creating GUVs with less cost, effort and time, which could further benefit studying closed membrane systems.

Reassembly of the vesicular structure of niosomes after their destruction in a mechanical field

This paper presents, for the first time, evidence for vesicle destruction and payload loss at the stage of purification of niosome dispersions by centrifugation, an important operation in the assembly of vesicular materials. The ability of niosomes of different compositions to reassemble, i.e., to restore the vesicular structure after destruction in the field of centrifugal forces, was demonstrated by dynamic light scattering and fluorescence spectroscopy. The kinetics of reassembly of vesicular structures is determined by the strength of the centrifugal field and the composition of niosomes. In contrast to ternary compositions, where particle size and modality are essentially unchanged after redispersion of the precipitate resulting from centrifugation, niosome dispersions containing anionic dicetyl phosphate includes micron-sized particles after redispersion, which vary in size over a wide range throughout the observation period. The reassembly process is complicated by the presence of charge on the surface of the niosomes. Elastic niosomes - ethosomes have been synthesised which, due to the high deformability of the shells, are less susceptible to destruction in the centrifugal field and retain the contents of the aqueous core. Using the "energy landscape" approximation, it is shown that vesicular structures assembled during hydration and reassembled after their centrifugation occupy different positions in the energetic pathway of their preparation. The results obtained should also be taken into account when determining the entrapment efficiency, since this procedure uses centrifugation to separate the load. It is important to note that the physical stability of niosomes, which is usually considered in terms of the functional activity of particles, is manifest and should be considered at the material preparation stage.

Advances in microscopy characterization techniques for lipid nanocarriers in drug delivery: a comprehensive review

This review paper provides an in-depth analysis of the significance of lipid nanocarriers in drug delivery and the crucial role of characterization techniques. It explores various types of lipid nanocarriers and their applications, emphasizing the importance of microscopy-based characterization methods such as light microscopy, confocal microscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The paper also delves into sample preparation, quantitative analysis, challenges, and future directions in the field. The review concludes by underlining the pivotal role of microscopy-based characterization in advancing lipid nanocarrier research and drug delivery technologies.

Long-Term Stable Liposome Modified by PEG-Lipid in Natural Seawater

This paper describes the stabilization of liposomes using a PEGylated lipid, N-(methylpolyoxyethylene oxycarbonyl)-1,2-distearoyl-sn-glycero-3-phosphoethanolamine sodium salt (DSPE-PEGs), and the evaluation of the survival rate in natural seawater for future environmental applications. Liposomes in natural seawater were first monitored by confocal microscopy, and the stability was compared among different lengths and the introduction ratio of DSPE-PEGs. The survival rate increased with an increase in the PEG ratio. In addition, the survival rate in different cationic solutions (Na+, K+, Mg2+, and Ca2+ solutions) was studied to estimate the effects of the DSPE-PEG introduction. We propose that these variations in liposome stability are due to the cations, specifically the interaction between the poly(ethylene glycol) (PEG) chains and divalent ions, which contribute to making it difficult for cations to access the lipid membrane. Our studies provide insights into the use of PEG lipids and may offer a promising approach to the fabrication of liposomal molecular robots using different natural environments.

Lipid vesicle-based molecular robots

A molecular robot, which is a system comprised of one or more molecular machines and computers, can execute sophisticated tasks in many fields that span from nanomedicine to green nanotechnology. The core parts of molecular robots are fairly consistent from system to system and always include (i) a body to encapsulate molecular machines, (ii) sensors to capture signals, (iii) computers to make decisions, and (iv) actuators to perform tasks. This review aims to provide an overview of approaches and considerations to develop molecular robots. We first introduce the basic technologies required for constructing the core parts of molecular robots, describe the recent progress towards achieving higher functionality, and subsequently discuss the current challenges and outlook. We also highlight the applications of molecular robots in sensing biomarkers, signal communications with living cells, and conversion of energy. Although molecular robots are still in their infancy, they will unquestionably initiate massive change in biomedical and environmental technology in the not too distant future.

Biofilm Removal from In Vitro Narrow Geometries Using Single and Dual Pulse Er:YAG Laser Photoacoustic Irrigation

The disinfection and removal of biofilm from titanium dental implants remains a great challenge in oral medicine. Here we present results of novel photoacoustic irrigation laser modalities for biofilm removal in model geometries mimicking the peri-implant pocket. The efficacy of single pulse (Er:YAG-SSP) and dual pulse (Er:YAG-AutoSWEEPS) photoacoustic irrigation modalities were determined for Enterococcus faecalis biofilm decontamination from titanium surfaces in narrow cylindrical and square gap geometries. The density of bacteria as well as the number of live bacteria were determined prior and after different photoacoustic treatments. Both SSP and AutoSWEEPS photoacoustic irrigation techniques removed at least 92% of biofilm bacteria during the 10 s photoacoustic treatment. The effectiveness of cleaning was better in the narrow square gap geometry compared to the cylindrical geometry. The dual pulse Er:YAG-AutoSWEEPS photoacoustic irrigation showed better results compared to SSP modality. No chemical adjuvants were needed to boost the effectiveness of the photoacoustic irrigation in the saline solution. The results imply that photoacoustic irrigation is an efficient cleaning method for debridement and decontamination in narrow geometries and should be considered as a new therapeutic option for the treatment of peri-implant diseases.

Locally induced shockwaves for selective perforation of cargo loaded lipid vesicles with temporal and spatial control

Controlled poration of lipid membranes is crucial for numerous biomimetic applications such as targeted drug delivery. Although several chemical and physical mechanisms have been proposed for the poration of synthetic membranes, achieving good temporal and spatial control remains a challenge. In this study, we introduce a novel method for membrane poration that utilizes the mechanical shockwave generated by the photo-acoustic effect, which occurs when an optically opaque microparticle is illuminated by a near-infrared laser of optical tweezers. We show that the shockwave effectively porates membranes of giant unilamellar vesicles in close proximity to the microparticle without damaging nearby cells, which is a desirable outcome for potential targeted drug delivery. The poration effect is nonspecific and operates on both liquid and gel phase membranes. Since the photo-acoustic effect can be triggered by standard optical tweezers, this method holds broad applicability in various experimental settings within the field of soft matter research.

Inactivation of the enveloped virus phi6 with hydrodynamic cavitation

The COVID -19 pandemic reminded us that we need better contingency plans to prevent the spread of infectious agents and the occurrence of epidemics or pandemics. Although the transmissibility of SARS-CoV-2 in water has not been confirmed, there are studies that have reported on the presence of infectious coronaviruses in water and wastewater samples. Since standard water treatments are not designed to eliminate viruses, it is of utmost importance to explore advanced treatment processes that can improve water treatment and help inactivate viruses when needed. This is the first study to investigate the effects of hydrodynamic cavitation on the inactivation of bacteriophage phi6, an enveloped virus used as a SARS-CoV-2 surrogate in many studies. In two series of experiments with increasing and constant sample temperature, virus reduction of up to 6.3 logs was achieved. Inactivation of phi6 at temperatures of 10 and 20 °C occurs predominantly by the mechanical effect of cavitation and results in a reduction of up to 4.5 logs. At 30 °C, the reduction increases to up to 6 logs, where the temperature-induced increased susceptibility of the viral lipid envelope makes the virus more prone to inactivation. Furthermore, the control experiments without cavitation showed that the increased temperature alone is not sufficient to cause inactivation, but that additional mechanical stress is still required. The RNA degradation results confirmed that virus inactivation was due to the disrupted lipid bilayer and not to RNA damage. Hydrodynamic cavitation, therefore, has the potential to inactivate current and potentially emerging enveloped pathogenic viruses in water at lower, environmentally relevant temperatures.

Liposomes for encapsulation of liposoluble vitamins (A, D, E and K): Comparation of loading ability, storage stability and bilayer dynamics

To understand the encapsulation difference and stability mechanism of nanoliposomes (NLPs) loaded with different kinds and loads of liposoluble vitamins (LSV, including VA, VD, VE, and VK), the physicochemical stability during three-months storage and bilayer membrane properties of LSV-NLPs were evaluated. The results suggested that VD and VE were not suitable for high-load (≥30 wt%) encapsulation, but the stability of other LSV-NLPs was excellent during storage. Their particle size was less than 100 nm, the polydispersity index was less than 0.3, and the retention rate of VE and VK remained above 85 %. LSV encapsulation inhibited malondialdehyde production, decreased liposome surface roughness, and improved nanoliposome rigidity. The order of occupying capacity of LSV to the hydrophobic zone of the bilayer was VK＞VD＞VE＞VA, and the stability of LSV located in the hydrophobic region was better. Except for high-load VD and VE, the other LSV encapsulation increased the microviscosity of the lipid-water interface and hydrophobic zone by 0.5 ∼ 7.1 times and 0.5 ∼ 20 times, respectively. The accumulation of acyl chain was enhanced by 0.2 ∼ 4 times, and the interchain longitudinal and intra-chain transverse order degree was increased by 10.89 %∼144.35 % and 3.26 %∼115.52 %, respectively. High microviscosity and tight chain stacking limited bilayer fluidity and thus improve LSV-NLPs stability. This work will contribute to the application of nanoliposomes as liposoluble vitamin carriers in the food industry.

Silica-coated gold nanorods with hydrophobic modification show both enhanced two-photon fluorescence and ultrasound drug release

Hydrophobically-modified silica-coated gold nanorods are presented here as multifunctional theranostic agents. A single modification both increases two-photon fluorescence and promotes cavitation-based acoustic signal for imaging. A two-fold greater release of small molecule drugs was observed under ultrasound-mediated conditions as compared to passive release without ultrasound.

Unfolding the Potency of Adenosine in Targeting Triple Negative Breast Cancer via Paclitaxel-Incorporated pH-Responsive Stealth Liposomes

Triple-negative breast cancer (TNBC) belongs to the category of the most destructive forms of breast cancer. Being a highly potent chemotherapeutic agent, paclitaxel (PTX) is extensively utilized in the management of various cancers. Commercially available PTX formulations contain non-targeted drug carriers that result in low antitumor activity because of non-specific tissue distribution. Thus, to resolve this issue, we designed PTX-loaded pH-sensitive liposomes (pH Lipos) in the present investigation and used adenosine (ADN) as a targeting ligand. Further, d-α-tocopheryl polyethylene glycol succinate (TPGS) was incorporated into the liposomes to impart a stealth effect to the system. For the development of these pH Lipos, different conjugates were synthesized (ADN-CHEMS and TPGS-ADN) and further utilized for the preparation of ADN-PEG-pH Lipo and ADN-pH Lipo by a thin-film hydration method. DOPE:HSPC:CHEMS:cholesterol at a molar ratio of 3:3:2:2 was selected for the preparation of pH-Lipo possessing 7.5% w/w drug loading. They showed a particle size below 140 nm, a PDI below 0.205, and a % EE greater than 60%. All of the pH Lipos displayed a biphasic pattern of PTX release at pH 7.4 and 5.5. However, the percent drug release at pH 5.5 was substantially greater because of the pH-sensitive nature of the liposomes. The MDA MB 231 and 4T1 cell lines depicted improvement in the qualitative as well as quantitative cellular uptake of PTX ADN-PEG-pH Lipo with a substantial decrease in the IC₅₀ value. Moreover, a higher apoptotic index was observed with pH Lipo compared to free PTX. PTX ADN-PEG-pH Lipo revealed a 3.98- and 3.41-fold rise in the AUC and t_1/2 values of PTX compared to Intaxel, respectively. Overall, characteristic decreases in tumor volume and serum toxicity marker levels were observed, which confirmed the development of an efficient and safe formulation.

Dual Effects of Presynaptic Membrane Mimetics on α-Synuclein Amyloid Aggregation

Aggregation of intrinsically disordered α-synuclein (αSN) under various conditions is closely related to synucleinopathies. Although various biological membranes have shown to alter the structure and aggregation propensity of αSN, a thorough understanding of the molecular and mechanical mechanism of amyloidogenesis in membranes remains unanswered. Herein, we examined the structural changes, binding properties, and amyloidogenicity of three variations of αSN mutants under two types of liposomes, 1,2-Dioleoyl-sn-glycero-3-Phosphocholine (DOPC) and presynaptic vesicle mimetic (Mimic) membranes. While neutrally charged DOPC membranes elicited marginal changes in the structure and amyloid fibrillation of αSNs, negatively charged Mimic membranes induced dramatic helical folding and biphasic amyloid generation. At low concentration of Mimic membranes, the amyloid fibrillation of αSNs was promoted in a dose-dependent manner. However, further increases in the concentration constrained the fibrillation process. These results suggest the dual effect of Mimic membranes on regulating the amyloidogenesis of αSN, which is rationalized by the amyloidogenic structure of αSN and condensation-dilution of local αSN concentration. Finally, we propose physicochemical properties of αSN and membrane surfaces, and their propensity to drive electrostatic interactions as decisive factors of amyloidogenesis.

Cavitation bubble interaction with compliant structures on a microscale: A contribution to the understanding of bacterial cell lysis by cavitation treatment

Numerous studies have already shown that the process of cavitation can be successfully used for water treatment and eradication of bacteria. However, most of the relevant studies are being conducted on a macro scale, so the understanding of the processes at a fundamental level remains poor. In attempt to further elucidate the process of cavitation-assisted water treatment on a scale of a single bubble, the present paper numerically addresses interaction between a collapsing microbubble and a nearby compliant structure, that mechanically and structurally resembles a bacterial cell. A fluid-structure interaction methodology is employed, where compressible multiphase flow is considered and the bacterial cell wall is modeled as a multi-layered shell structure. Simulations are performed for two selected model structures, each resembling the main structural features of Gram-negative and Gram-positive bacterial cell envelopes. The contribution of two independent dimensionless geometric parameters is investigated, namely the bubble-cell distance δ and their size ratio ς. Three characteristic modes of bubble collapse dynamics and four modes of spatiotemporal occurrence of peak local stresses in the bacterial cell membrane are identified throughout the parameter space considered. The former range from the development of a weak and thin jet away from the cell to spherical bubble collapses. The results show that local stresses arising from bubble-induced loads can exceed poration thresholds of cell membranes and that bacterial cell damage could be explained solely by mechanical effects in absence of thermal and chemical ones. Based on this, the damage potential of a single microbubble for bacteria eradication is estimated, showing a higher resistance of the Gram-positive model organism to the nearby bubble collapse. Microstreaming is identified as the primary mechanical mechanism of bacterial cell damage, which in certain cases may be enhanced by the occurrence of shock waves during bubble collapse. The results are also discussed in the scope of bacteria eradication by cavitation treatment on a macro scale, where processes of hydrodynamic and ultrasonic cavitation are being employed.

Bacterial cell wall material properties determine E. coli resistance to sonolysis

The applications of bacterial sonolysis in industrial settings are plagued by the lack of the knowledge of the exact mechanism of action of sonication on bacterial cells, variable effectiveness of cavitation on bacteria, and inconsistent data of its efficiency. In this study we have systematically changed material properties of E. coli cells to probe the effect of different cell wall layers on bacterial resistance to ultrasonic irradiation (20 kHz, output power 6,73 W, horn type, 3 mm probe tip diameter, 1 ml sample volume). We have determined the rates of sonolysis decay for bacteria with compromised major capsular polymers, disrupted outer membrane, compromised peptidoglycan layer, spheroplasts, giant spheroplasts, and in bacteria with different cell physiology. The non-growing bacteria were 5-fold more resistant to sonolysis than growing bacteria. The most important bacterial cell wall structure that determined the outcome during sonication was peptidoglycan. If peptidoglycan was remodelled, weakened, or absent the cavitation was very efficient. Cells with removed peptidoglycan had sonolysis resistance equal to lipid vesicles and were extremely sensitive to sonolysis. The results suggest that bacterial physiological state as well as cell wall architecture are major determinants that influence the outcome of bacterial sonolysis.

Microbubble dynamics and jetting near tissue-phantom biointerfaces

Precise excitation of cavitation is a promising mechanism for microsurgery procedures and targeted drug delivery enhancement. The underlying phenomenon of interest, jetting behaviour of oscillating cavitation bubbles, occurs due to near-surface interactions between the boundary, liquid, and bubble. Within this study we measured boundary effects on the cavitation bubble dynamics and morphology, with an emphasis on observation and measurement of jetting behaviour near tissue-phantom biointerfaces. An important mechanism of boundary poration has been observed using time-resolved optical microscopy and explained for different tissue-phantom surface densities and Young's modulus. Below a critical distance to the boundary, around γ = 1.0, the resulting jets penetrated the tissue-phantom, resulting in highly localized few micrometer diameter jets.

Liposome destruction by a collapsing cavitation microbubble: A numerical study

Hydrodynamic cavitation poses as a promising new method for wastewater treatment as it has been shown to be able to eradicate bacteria, inactivate viruses, and destroy other biological structures, such as liposomes. Although engineers are already commercializing devices that employ cavitation, we are still not able to answer the fundamental question: What exactly are the damaging mechanisms of hydrodynamic cavitation in various applications? In this light, the present paper numerically addresses the interaction between a single cavitation microbubble and a nearby lipid vesicle of a similar size. A coupled fluid-structure interaction model is employed, from which three critical modes of vesicle deformation are identified and temporally placed in relation to their corresponding driving mechanisms: (a) unilateral stretching at the waist of the liposome during the first bubble collapse and subsequent shock wave propagation, (b) local wrinkling at the tip until the bubble rebounds, and (c) bilateral stretching at the tip of the liposome during the phase of a second bubble contraction. Here, unilateral and bilateral stretching refer to the local in-plane extension of the bilayer in one and both principal directions, respectively. Results are discussed with respect to critical dimensionless distance for vesicle poration and rupture. Liposomes with initially equilibrated envelopes are not expected to be structurally compromised in cases with δ>1.0, when a nearby collapsing bubble is not in their direct contact. However, the critical dimensionless distance for the case of an envelope with pre-existing pores is identified at δ=1.9. Additionally, the influence of liposome-bubble size ratio is addressed, from which a higher potential of larger bubbles for causing stretching-induced liposome destruction can be identified.

Delivery of trans-membrane proteins by liposomes; the effect of liposome size and formulation technique on the efficiency of protein delivery

Channelopathies are disorders caused by reduced expression or impaired function of ion channels. Most current therapies rely on symptomatic treatment without addressing the underlying cause. We have recently established proof of principle for delivery of functional ion channel protein into the membrane of target cells using fusogenic liposomes incorporating glycine receptor (GlyR)-containing cell membrane fragments (CMF) that were formulated by thin film hydration. Here, the effect of liposome size and the formulation technique on the performance of the delivery vehicle was assessed. Three types of liposomes were prepared using lecithin and cholesterol, (i) small (SL), and (ii) large (LL) liposomes made by thin film hydration, and (iii) small liposomes prepared by vortex agitation (V-SL). All liposomes were evaluated for their ability to (i) incorporate GlyR-rich CMF, (ii) fuse with the cell membrane of target cells and (iii) deliver functional GlyR, as assessed by patch-clamp electrophysiology. SL prepared by thin film hydration offered the most effective delivery of glycine receptors that gave clear glycine-mediated currents in target cells. LL showed higher incorporation of CMF, but did not effectively fuse with the target cell membrane, while V-SL did not incorporate sufficient amounts of CMF. Additionally, SL showed minimalin vivotoxicity upon intrathecal injection in mice. Thus, liposome-mediated delivery of membrane proteins may be a promising therapeutic approach for the treatment of channelopathies.

Luminescence intensity of vortex cavitation in a Venturi tube changing with cavitation number

Hydrodynamic cavitation in a Venturi tube produces luminescence, and the luminescence intensity reaches a maximum at a certain cavitation number, which is defined by upstream pressure, downstream pressure, and vapor pressure. The luminescence intensity of hydrodynamic cavitation can be enhanced by optimizing the downstream pressure at a constant upstream pressure condition. However, the reason why the luminescence intensity increases and then decreases with an increase in the downstream pressure remains unclear. In the present study, to clarify the mechanism of the change in the luminescence intensity with cavitation number, the luminescence produced by the hydrodynamic cavitation in a Venturi tube was measured, and the hydrodynamic cavitation was precisely observed using high-speed photography. The sound velocity in the cavitating flow field, which affects the aggressive intensity of the cavitation, was evaluated. The collapse of vortex cavitation was found to be closely related to the luminescence intensity of the hydrodynamic cavitation. A method to estimate the luminescence intensity of the hydrodynamic cavitation considering the sound velocity was developed, and it was demonstrated that the estimated luminescence intensity agrees well with the measured luminescence intensity.

Imaging of photoacoustic-mediated permeabilization of giant unilamellar vesicles (GUVs)

Target delivery of large foreign materials to cells requires transient permeabilization of the cell membrane without toxicity. Giant unilamellar vesicles (GUVs) mimic the phospholipid bilayer of the cell membrane and are also useful drug delivery vehicles. Controlled increase of the permeability of GUVs is a delicate balance between sufficient perturbation for the delivery of the GUV contents and damage to the vesicles. Here we show that photoacoustic waves can promote the release of FITC-dextran or GFP from GUVs without damage. Real-time interferometric imaging offers the first movies of photoacoustic wave propagation and interaction with GUVs. The photoacoustic waves are seen as mostly compressive half-cycle pulses with peak pressures of ~ 1 MPa and spatial extent FWHM ~ 36 µm. At a repetition rate of 10 Hz, they enable the release of 25% of the FITC-dextran content of GUVs in 15 min. Such photoacoustic waves may enable non-invasive targeted release of GUVs and cell transfection over large volumes of tissues in just a few minutes.

Cavitation bubble interaction with a rigid spherical particle on a microscale

Cavitation bubble collapse close to a submerged sphere on a microscale is investigated numerically using a finite volume method in order to determine the likelihood of previously suspected mechanical effects to cause bacterial cell damage, such as impact of a high speed water jet, propagation of bubble emitted shock waves, shear loads, and thermal loads. A grid convergence study and validation of the employed axisymmetric numerical model against the Gilmore's equation is performed for a case of a single microbubble collapse due to a sudden ambient pressure increase. Numerical simulations of bubble-sphere interaction corresponding to different values of nondimensional bubble-sphere standoff distance δ and their size ratio ε are carried out. The obtained results show vastly different bubble collapse dynamics across the considered parameter space, from the development of a fast thin annular jet towards the sphere to an almost spherical bubble collapse. Although some similarities in bubble shape progression to previous studies on larger bubbles exist, it can be noticed that bubble jetting is much less likely to occur on the considered scale due to the cushioning effects of surface tension on the intensity of the collapse. Overall, the results show that the mechanical loads on a spherical particle tend to increase with a sphere-bubble size ratio ε, and decrease with their distance δ. Additionally, the results are discussed with respect to bacteria eradication by hydrodynamic cavitation. Potentially harmful mechanical effects of bubble-sphere interaction on a micro scale are identified, namely the collapse-induced shear loads with peaks of a few megapascals and propagation of bubble emitted shock waves, which could cause spatially highly variable compressive loads with peaks of a few hundred megapascals and gradients of 100 MPa/μm.

A review on hydrodynamic cavitation disinfection: The current state of knowledge

Disinfection, which aims to eliminate pathogenic microorganisms, is an essential step of water treatment. Hydrodynamic cavitation (HC) has emerged as a promising technology for large-scale disinfection without introducing new chemicals. HC, which can effectively induce sonochemistry by mechanical means, creates extraordinary conditions of pressures of ~1000 bar, local hotspots with ~5000 K, and high oxidation (hydroxyl radicals) in room environment. These conditions can produce highly destructive effects on microorganisms in water. In addition, the enhancements of chemical reactions and mass transfers by HC produce the synergism between HC and disinfectants or other physical treatment methods. HC is generated by hydrodynamic cavitation reactors (HCRs), therefore, their performance basically determines the effectiveness, economical efficiency, and applicability of HC disinfection. Therefore, developing high-performance HCRs and revealing the corresponding disinfection mechanisms are the most crucial issues today. In this review, we summarize the fundamental principles of HC and HCRs and recent development in HC disinfection. The energy release from cavitation phenomenon and corresponding mechanisms are elaborated. The performance (effectiveness, treatment ratio, and cost) of various HCRs, effects of treatment conditions on performance, and applicability of HC disinfection are evaluated and discussed. Finally, recommendations are provided for the future progress based on the analysis of previous studies.

Kelvin-Helmholtz-like instability of phospholipid bilayers under shear flow: System-size dependence

We performed a series of molecular dynamics (MD) simulations of phospholipid bilayers under shear flow to estimate the effect of the system size on Kelvin-Helmholtz (KH)-like instability of the bilayer at the molecular scale. To extend the estimation by the MD simulations to the microscale, we introduced linear stability analysis for the fluid-fluid interface consisting of a thin membrane. For both the MD simulations and theoretical model, the critical velocity difference across the bilayer, where instability occurs, decreased with increasing wavelength of the bilayer undulation λ, which corresponds to the system size. When λ was more than about ten times larger than the bilayer thickness, the critical velocity difference in the MD simulations was in quantitative agreement with that obtained by the theoretical model. This means that the theoretical model is applicable for the shear-induced KH-like instability of the bilayer for large λ. The theoretical model showed that the critical velocity difference for the KH-like instability was proportional to λ^{-3/2}. Based on these results, we discuss the implications of the shear-induced bilayer instability in the shear-induced cell damage observed in experiments.

Hydrodynamic Cavitation: A Promising Technology for Industrial-Scale Synthesis of Nanomaterials

One of the most challenging issues for the large-scale application of nanomaterials, especially nanocarbons, is the lack of industrial synthetic methods. Sonochemistry, which creates an extreme condition of high pressure and temperature, has been thereby applied for synthesizing a wide variety of unusual nanostructured materials. Hydrodynamic cavitation (HC), characterized by high effectiveness, good scalability, and synergistic effect with other physical and chemical methods, has emerged as the promising sonochemistry technology for industrial-scale applications. Recently, it was reported that HC can not only significantly enhance the performance of biochar, but also preserve or improve the respective chemical composition. Moreover, the economic efficiency was found to be at least one order of magnitude higher than that of conventional methods. Due to the great potential of HC in the industrial-scale synthesis of nanomaterials, the present perspective focuses on the mechanism of sonochemistry, advances in HC applications, and development of hydrodynamic cavitation reactors, which is supposed to contribute to the fundamental understanding of this novel technology.