Hydrodynamic cavitation-enhanced photocatalytic activity of P-doped TiO2 for degradation of ciprofloxacin: Synergetic effect and mechanism

Synergistic enhancement in hydrodynamic cavitation combined with peroxymonosulfate fenton-like process for bpa degradation: New insights into the role of cavitation bubbles in regulation reaction pathway

The combination of hydrodynamic cavitation (HC) and Fenton-like oxidation technology can dramatically enhance the pollutant removal capacity, however, the synergistic effect of cavitation and catalysts on reactive oxygen species (ROS) generation remained enigmatic. In this study, we established a combined system based on HC and Ce-MnFe2O4 activated peroxymonosulfate (PMS) for BPA removal, and attentions were paid on the role of cavitation bubbles. The results show that the combination of HC in Ce-MnFe2O4 activated PMS could mediate the degradation of BPA from the non-radical pathway dominated by 1O2 to •O2- dominated radical pathway. Both controlled experiments and theoretical calculations revealed that the cavitation bubbles with different sizes play the dominant role in ROS generation. The microjets produced by the collapse of cavitation bubbles could create a large number of oxygen vacancy defects on Ce-MnFe2O4 surface, which modify the activation barrier of PMS and facilitate the generation of •O2- thermodynamically. The stable existing cavitation bubbles with the size of 100∼400 nm could create considerable gas-liquid interface. The molecular dynamics simulations show that the nano bubbles can concentrate the BPA and increase the probability of contacts between BPA and Ce-MnFe2O4, hence effectively solve the issues of short lifetime of •O2- radicals and limited mass transfer distance to strengthen the reaction. In addition, the PMS/Ce-MnFe2O4/HC system not only achieves the satisfied COD (95 %) and TOC (65 %) removal efficiency but also enabled the BPA-contaminated water with a low energy cost of 0.065 kWh·m-3 and oxidant cost, highlighting the application potential of the HC technology for contaminated water.

Batch and column studies for the removal of basic red-46 dye and textile by using magnesium oxide (MgO), strontium titanium trioxide (SrTiO3), cobalt- and iron-doped lanthanum chromium trioxide (Co.Fe.LaCrO3), and cadmium sulfide (CdS)-doped graphene oxide nanocomposites

Despite efforts to reduce the risk of toxic chemicals, colors, and dyes being released into the environment from urban and industrial areas, there is still cause for concern. Colored water must be filtered and sterilized before it can be used for irrigation. The utilization of metal oxide and nanocomposite materials in wastewater treatment procedures appears to be a viable option for the future. Therefore, different compounds were doped with graphene oxide to identify the best material for dye removal by the adsorption process. According to recent studies, the ideal conditions for graphene oxide-doped magnesium oxide (GO/MgO) are as follows: pH 10 showed the highest adsorption capacity (qe) at 49.4 mg/g; an adsorbent dosage of 0.01 g/50 mL showed 48.3 mg/g qe; a shaking time of 30 min resulted in 44.2 mg/g qe; an initial dye concentration of 100 mg/L yielded 53.6 mg/g qe; and a temperature of 35 °C gave 49.5 mg/g qe. For graphene oxide-doped strontium titanate (GO/SrTiO3), the optimum conditions were as follows: pH 10 with 45.8 mg/g qe; an adsorbent dose of 0.01 g/50 mL with 40.5 mg/g qe; a shaking time of 30 min with 75 mg/g qe; and a temperature of 35 °C with 44.7 mg/g qe. Graphene oxide-doped cobalt and iron-doped lanthanum chromium titanate (GO/Co.Fe.LaCrO3) showed optimum conditions of pH 9 with 34.2 mg/g qe; an adsorbent dose of 0.01 g/50 mL with 27.5 mg/g qe; a shaking time of 45 min with 33.2 mg/g qe; an initial dye concentration of 100 mg/L with 37.6 mg/g qe; and a temperature of 35 °C with 42.5 mg/g qe. Graphene oxide-doped cadmium sulfide (GO/CdS) showed the following optimum conditions: pH 8 with 23.1 mg/g qe; an adsorbent dose of 0.01 g/50 mL with 25.5 mg/g qe; an initial dye concentration of 75 mg/L with 28.3 mg/g qe; and a temperature of 35 °C with 33.5 mg/g qe. The pseudo-first-order model was the best fit only for graphene oxide-doped magnesium oxide (GO/MgO) with an R2 value of 0.966, while the pseudo-second-order adsorption isotherm was the best fit for all four products, with R2 values ranging from 0.991 to 0.998. Additionally, the Langmuir adsorption isotherms provided good results for all four products, with R2 values ranging from 0.957 to 0.985. The Freundlich adsorption kinetics showed satisfactory fit only for graphene oxide-doped magnesium oxide (GO/MgO) and graphene oxide-doped cadmium sulfide (GO/CdS), with R2 values of 0.951 and 0.982, respectively. To examine the characteristics and practicality of the adsorption process, certain thermodynamic variables were calculated. The adsorption capability of the most efficient nanocomposites for the degradation of basic red-46 was significantly affected by various concentrations of heavy metal ions and electrolytes. In dye solutions containing surfactants/detergents, the adsorption efficiency of several effective photocatalysts for basic dyes was significantly reduced. A 0.5 M HCl solution was found to be the most effective for desorption. In column investigations, the optimal bed height, flow velocity, and dye intake levels were determined to be 3 cm, 1.8 mL/min, and 70 mg/L, respectively, for maximal adsorption of basic red-46. The adsorption investigation of genuine textile waste products has also been carried out to facilitate the practical deployment of this approach. The methods used in this study were cost-effective, easy to handle, and eco-friendly and involved no hazardous materials in the synthesis, making the resulting materials non-hazardous. All these methods were part of green chemistry.

Photocatalytic degradation of ciprofloxacin from water with waste polystyrene and TiO2 composites

Ciprofloxacin (CIP) is one of the widely used antibiotics with a broad antimicrobial spectrum in the fluoroquinolone type. Its concentration in water bodies has increased over the years due to its frequent use. Since ciprofloxacin in the aquatic ecosystem adversely affects human health as well as other organisms, it must be removed from wastewater. The aim of this study was to develop Polystyrene (PS) and Titanium dioxide (TiO2) composites that can be used as catalysts in CIP removal by photocatalytic process. Waste PS (obtained from disposable cutlery) was used in the synthesis of these composites. In this study, PS-TiO2 composites with different PS content (C20, C50, C80; the numbers in the names indicate the PS percentage in the composite by weight) were synthesized. This is important in terms of the use of one waste in the removal of another waste. This process was optimized using Box-Behnken design, one of the response surface method. Parameters such as the amount of polymer in the composite, pH and initial CIP concentration were studied and their effects on CIP removal were found. The validity and adequacy of the selected model were evaluated according to the relevant statistical data. These are R2 = 0.9751, adjusted R2 = 0.9565, the model's p-value <0.05 and the lack of fit-value 0.246. Optimum conditions for CIP removal were obtained when the C50 was used, with a pH value of 3 and an initial CIP concentration of 5 mg/L. In the process carried out under these conditions, the CIP removal was found to be 95.01 % at the end of 180 min. This value was predicted as 94.37 % in the model. According to these results, C50 composite synthesized with waste PS can be used effectively for CIP removal.

Degradation of methyl orange using hydrodynamic Cavitation, H2O2, and photo-catalysis with TiO2-Coated glass Fibers: Key operating parameters and synergistic effects

Advanced oxidation processes (AOPs) are eco-friendly, and promising technology for treating dye containing wastewater. This study focuses on investigating the removal of methyl orange (MO), an azo dye, from a synthetic wastewater through the use of hydrodynamic cavitation (HC), both independently and in combination with hydrogen peroxide (H2O2), as an external oxidant, as well as photocatalysis (PC) employing catalyst coated on glass fibers tissue (GFT). The examination of various operating parameters, including the pressure drop and the concentration of H2O2, was systematically conducted to optimize the degradation of MO. A per-pass degradation modelwas used to interpret and describe the experimental data. The data revealed that exclusive employment of HC using a vortex-based cavitation device at 1.5 bar pressure drop, resulted in a degradation exceeding 96 % after 100 passes, equivalent to 230 min of treatment (cavitation yield of 3.6 mg/kJ for HC), with a COD mineralization surpassing 12 %. The presence of a small amount of H2O2 (0.01 %) significantly reduced the degradation time from 230 min to 36 min (16 passes), achieving a degradation of 99.8 % (cavitation yield of 6.77 mg/kJ for HC) with COD mineralization rate twice as much as HC alone, indicating a synergistic effect of 4.8. The degradation time was further reduced to 21 min by combining HC with PC using TiO2-coated glass fibers and H2O2, (cavitation yield of 11.83 mg/kJ for HC), resulting in an impressive synergistic effect of 9.2 and COD mineralization twice as high as the HC/H2O2 system. The results demonstrate that HC based hybrid AOPs can be very effective for treating and mineralizing azo dyes in water.

Tailoring Interfacial Physicochemical Properties in Cu2O-TiO2@rGO Heterojunction: Insights from EXAFS and Electron Trap Distribution Analysis

In this study, a solution-based synthesis technique was utilized to produce Cu2O nanoparticles (NPs) on TiO2 nanofibers (TNF), which were then subsequently coated with reduced graphene oxide (rGO) nanosheets. In the absence of any cocatalyst, CTNF@rGO-3% composite displayed an ideal photocatalytic H2 evolution rate of 96 μmol g-1 h-1 under visible light irradiation, this was 10 times higher than that of pure TNF. At 420 nm, the apparent quantum efficiency of this composite reached a maximum of 7.18%. Kelvin probe force microscopy demonstrated the formation of an interfacial electric field that was oriented from CTNF to rGO and served as the driving force for interfacial electron transfer. The successful establishment of an intimate interface between CTNF@rGO facilitated the efficient transfer of charges and suppressed the rate of recombination of photogenerated electron-hole pairs, leading to a substantial enhancement in photocatalytic performance. X-ray photoelectron spectroscopy, photoluminescence spectra, and electrochemical characterization provide further confirmation that formation of a heterojunction between CTNF@rGO leads to an extension in the lifetimes of the photogenerated charge carriers. The experimental evidence suggests that a p-n heterojunction is the mechanism responsible for the significant photocatalytic activity observed in the CTNF@rGO composite during H2 evolution.

Recent progress on sonochemical production for the synthesis of efficient photocatalysts and the impact of reactor design

Sonochemical-assisted synthesis has flourished recently for the design of photocatalysts. The main power used is ultrasound that allows the nanomaterials shape and size modification and control. This review highlights the effect in formation mechanism by ultrasound application and the most common photocatalysts that were prepared via sonochemical techniques. Moreover, the challenge for the suitable reactor design for the synthesis of materials or for their photocatalytic evaluation is discussed since the most prominent reactor systems, batch, and continuous flow, has both advantages and drawbacks. This work summarises the significance of sonochemical synthesis for photocatalytic materials as a green technology that needs to be further investigated for the preparation of new materials and the scale up of developed reactor systems to meet industrial needs.