Hygiene aspect of treating human urine by alkaline dehydration

Direct evolution of an alkaline fungal laccase to degrade tetracyclines

A fungal laccase-mediator system capable of high effectively oxidizing tetracyclines under a wide pH range will benefit environmental protection. This study reported a directed evolution of a laccase PIE5 to improve its performance on tetracyclines oxidization at alkaline conditions. Two mutants, namely MutA (D229N/A244V) and MutB (N123A/D229N/A244V) were obtained. Although they shared a similar optimum pH and temperature as PIE5, the two mutants displayed approximately 2- and 5-fold higher specific activity toward the mediators ABTS and guaiacol at pHs 4.0 to 6.5, respectively. Simultaneously, their catalytic efficiency increased by 8.0- and 6.4-fold compared to PIE5. At a pH range of 5-8 and 28 °C, MutA or MutB at a final concentration of 2.5 U·mL-1 degraded 77 % and 81 % of 100 mg·L-1 tetracycline within 10 min, higher than PIE5 (45 %). Furthermore, 0.1 U·mL-1 MutA or MutB completely degraded 100 mg·L-1 chlortetracycline within 6 min in the presence of 0.1 mM ABTS. At pH 8.0, MutA degraded tetracycline and chlortetracycline following the routine pathways were reported previously based on LC-MS analysis.

Estimation of alkali dosage and contact time for treating human excreta containing viruses as an emergency response: a systematic review

Water, sanitation, and hygiene provisions are essential during emergencies to prevent infectious disease outbreaks caused by improper human excreta management in settlements for people affected by natural disasters and conflicts. Human excreta disinfection is required when long-term containment in latrines is not feasible on-site. Alkali additives, including lime, are effective disinfectants for wastewater and faecal sludge containing large amounts of solid and dissolved organic matter. The aim of this study was to determine the minimum dose and contact time of alkali additives for treating virus-containing human excreta in emergency situations. We used literature data collected by searching Google Scholar and Web of Science. The date of the last search for each study was 31th May 2023. Only peer-reviewed articles that included disinfection practices in combination with quantitative data for the physicochemical data of a matrix and viral decay were selected for data extraction. Two reviewers independently collected data from each study. We extracted datasets from 14 studies that reported quantitative information about their disinfection tests, including viral decay over time, matrix types, and physicochemical properties. Three machine learning algorithms were applied to the collected dataset to determine the time required to achieve specified levels of virus inactivation under different environmental conditions. The best model was used to estimate the contact time to achieve a 3-log10 inactivation of RNA virus in wastewater and faeces. The most important variables for predicting the contact time were pH, temperature, and virus type. The estimated contact time for 3 log inactivation of RNA virus was <2 h at pH 12, which was achieved by adding 1.8 and 3.1% slaked lime to wastewater and faeces, respectively. The contact time decreased exponentially with the pH of the sludge and wastewater. In contrast, the pH of the sludge and wastewater increased linearly with the slaked lime dosage. Lime treatment is a promising measure where long-term containment in latrine is not feasible in densely populated areas, as 1 day is sufficient to inactivate viruses. The relationship we have identified between required contact time and lime dosage is useful for practitioners in determining appropriate treatment conditions of human waste.

Concentrating stabilized urine with reverse osmosis: How does stabilization method and pre-treatment affect nutrient recovery, flux, and scaling?

Human urine can be used as a fertilizer, however, due to the high water content (97%), concentration is required to make transportation economically feasible. Reverse osmosis (RO) has been identified as an energy efficient concentration method. Furthermore, to maximize nitrogen recovery from source-separated urine it should be stabilized with an acid or base to prevent urea hydrolysis. However, the method of stabilization will have an impact on the downstream RO process. Calcium hydroxide is often used as a base stabilization method for human urine but would require pre-treatment to remove excess calcium and subsequent membrane scaling. Three pre-treatment methods such as air bubbling, NaHCO3 addition, and NH4HCO3 addition, were investigated in this study. Each method successfully reduced the scaling potential and air bubbling was determined to be the most effective method as it resulted in the highest nutrient recovery during concentration and did not require the addition of any chemicals. Base stabilization with air bubbling pre-treatment was then compared to urine stabilized with citric acid. Acid stabilized urine had a higher nitrogen recovery (7.6% higher). However, solids formed in the real acidified urine and during concentration a brown organic compound formed on the membrane surface. The crystals were identified as uric acid dihydrate and the brown organic fouling resulted in a significant decrease in permeate flux as compared to the base stabilized urine with air bubbling pre-treatment. At a 60% water recovery, 85.5% of the urea and 99.2% of the potassium was recovered in the brine stream and more than 99.9% of the phosphorus was recovered as a separate solid calcium phosphate fertilizer. Whilst nutrient recovery was higher with acid stabilization, the membrane fouling that occurred with this stabilization method meant that base stabilization with air bubbling pre-treatment was the preferred treatment option. It is recommended that acid stabilized urine be concentrated using evaporation processes instead.

On-site urine treatment combining Ca(OH)2 dissolution and dehydration with ambient air

We present the results of three field tests and three laboratory tests of a new physical-chemical urine treatment system, which can recover all nutrients, while pathogens are inactivated. The system consists of two steps. In the first reactor, biological processes including urea hydrolysis are prevented by mixing fresh urine with calcium hydroxide (Ca(OH)₂). Due to the high pH value and the high availability of calcium, phosphate can be recovered by precipitation. The high pH value also fosters the inactivation of microorganisms, including pathogens. In the second reactor, water is evaporated at low energy consumption by blowing unheated ambient air over the stabilized urine. Stabilization in the first reactor was successful in all field and laboratory tests. The pH value remained between 12 and 13, except for short dips due to shortages of Ca(OH)₂. Nearly all phosphorus (92-96%) precipitated and could be recovered as calcium phosphate in the first reactor, while nitrogen and potassium overflowed with the urine into the evaporation reactor. The efficiency of the second treatment step was very different for field and laboratory experiments and depended on the duration of the experiment. During a four-day laboratory test, nitrogen recovery was 98%. In contrast, nitrogen recovery was only around 20% in the long-term field experiments. The high nitrogen losses occurred, because biological urea hydrolysis was not inhibited anymore, when the pH value in the second reactor decreased due to the dissolution of high amounts of carbon dioxide from the ambient air. Potassium was not subject to any significant loss, and the measured recovery in the solid evaporation product was 98%. Evaporation rates ranged between 50 g m^-2 h^-1 (RH = 82±13%, T = 12±6°C) and 130 g m^-2 h^-1 (RH = 60±19%, T = 24±5°C) in the three field tests. Apart from some disturbances due to low supply of Ca(OH)₂, the urine module functioned without any substantial failures and was simple to maintain. The minimum consumption of Ca(OH)₂ at full capacity was 6 g·L^-1 urine and the electricity demand was 150 Wh kg^-1 water evaporated from urine, resulting in operational costs of 0.05 EUR pers^-1 d^-1.

State of the art of urine treatment technologies: A critical review

Over the last 15 years, urine treatment technologies have developed from lab studies of a few pioneers to an interesting innovation, attracting attention from a growing number of process engineers. In this broad review, we present literature from more than a decade on biological, physical-chemical and electrochemical urine treatment processes. Like in the first review on urine treatment from 2006, we categorize the technologies according to the following objectives: stabilization, volume reduction, targeted N-recovery, targeted P-recovery, nutrient removal, sanitization, and handling of organic micropollutants. We add energy recovery as a new objective, because extensive work has been done on electrochemical energy harvesting, especially with bio-electrochemical systems. Our review reveals that biological processes are a good choice for urine stabilization. They have the advantage of little demand for chemicals and energy. Due to instabilities, however, they are not suited for bathroom applications and they cannot provide the desired volume reduction on their own. A number of physical-chemical treatment technologies are applicable at bathroom scale and can provide the necessary volume reduction, but only with a steady supply of chemicals and often with high demand for energy and maintenance. Electrochemical processes is a recent, but rapidly growing field, which could give rise to exciting technologies at bathroom scale, although energy production might only be interesting for niche applications. The review includes a qualitative assessment of all unit processes. A quantitative comparison of treatment performance was not the goal of the study and could anyway only be done for complete treatment trains. An important next step in urine technology research and development will be the combination of unit processes to set up and test robust treatment trains. We hope that the present review will help guide these efforts to accelerate the development towards a mature technology with pilot scale and eventually full-scale implementations.

Willingness among food consumers to recycle human urine as crop fertiliser: Evidence from a multinational survey

Source-separating sanitation systems offer the possibility of recycling nutrients present in wastewater as crop fertilisers. Thereby, they can reduce agriculture's impacts on global sources, sinks, and cycles for nitrogen and phosphorous, as well as their associated environmental costs. However, it has been broadly assumed that people would be reluctant to perform the new sanitation behaviours that are necessary for implementing such systems in practice. Yet, few studies have tried to systematically gather evidence in support of this assumption. To address this gap, we surveyed 3763 people at 20 universities in 16 countries using a standardised questionnaire. We identified and systematically assessed cross-cultural and country-level explanatory factors that were strongly associated with people's willingness to consume food grown using human urine as fertiliser. Overall, 68% of the respondents favoured recycling human urine, 59% stated a willingness to eat urine-fertilised food, and only 11% believed that urine posed health risks that could not be mitigated by treatment. Most people did not expect to pay less for urine-fertilised food, but only 15% were willing to pay a price premium. Consumer perceptions were found to differ greatly by country and the strongest predictive factors for acceptance overall were cognitive factors (perceptions of risks and benefits) and social norms. Increasing awareness and building trust among consumers about the effectiveness of new sanitation systems via cognitive and normative messaging can help increase acceptance. Based on our findings, we believe that in many countries, acceptance by food consumers will not be the major social barrier to closing the loop on human urine. That a potential market exists for urine-fertilised food, however, needs to be communicated to other stakeholders in the sanitation service chain.

Inactivation of Cryptosporidium parvum oocysts and faecal indicator bacteria in cattle slurry by addition of ammonia

AIMS

To determine inactivation of Cryptosporidium parvum oocysts and reduction of Escherichia coli and enterococci in cattle slurry added aqueous ammonia.

METHODS AND RESULTS

Escherichia coli, enterococci and nonviable C. parvum oocysts (DAPI+PI+) were enumerated every second day for 2 weeks in cattle slurry amended with 60 mmol l^-1 aq. ammonia and compared with untreated slurry at three temperatures. Regardless of temperature, the proportion of nonviable C. parvum oocysts increased significantly faster over time in slurry with added ammonia than raw slurry (P = 0·021) corresponding to 62·0% higher inactivation (P = 0·001) at day 14. Additionally, 91·8% fewer E. coli and 27·3% fewer enterococci were observed in slurry added ammonia at day 14 compared to raw slurry.

CONCLUSION

The addition of aqueous ammonia to raw slurry significantly reduced the viability of C. parvum oocysts and numbers of bacterial indicators. Hence, ammonia is usable at lower pathogen concentrations in slurry before application to agricultural land.

SIGNIFICANCE AND IMPACT OF THE STUDY

Livestock waste is a valuable source of plant nutrients and organic matter, but may contain high concentrations of pathogens like E. coli and Cryptosporidium sp. that can be spread in the environment, and cause disease outbreaks. However, die-off rates of pathogens in organic waste can increase following increasing ammonia concentrations.

Inactivation kinetics modeling of Escherichia coli in concentrated urine for implementing predictive environmental microbiology in sanitation safety planning

Urine concentration (condensation) leads to the inactivation of pathogens in urine owing to a hyperosmotic environment. This study proposed an inactivation kinetic model of Escherichia coli (E. coli), a surrogate of human bacterial pathogens, in concentrated synthetic urine. The model parameters were obtained under an assumption that the inactivation rate of E. coli followed a binomial distribution, which made it possible to accurately simulate the time-course decay of E. coli in synthetic urine. The inactivation rate constant values obtained in concentrated urine samples, ammonium buffer solutions and carbonate buffer solutions indicated that the osmotic pressure was a relatively predominant cause for the inactivation of E. coli. The appropriate storage time was estimated using the approach of quantitative microbial risk assessment, which indicated that the 5-fold concentrated urine could be safely collected after 1-day storage when urea was hydrolyzed, whereas 91-hour storage was required for non-concentrated urine. The occupational risk was not negligible even with 6-month storage at 20 °C when urea was not hydrolyzed, which suggested that the urine storage styles should be clarified more minutely. The present study highlights the importance of "predictive environmental microbiology," which deals with inactivation kinetic models of microorganisms under varied environmental conditions to fully implement the hazard analysis and critical control point (HACCP) approach for the safe use of human excreta in agriculture.

Fate of Ascaris at various pH, temperature and moisture levels

Soil-transmitted helminths (STH) are intestinal worms that infect 24% of the world's population. Stopping the spread of STH is difficult, as the eggs are resilient (can withstand high pH) and persistent (can remain viable in soils for several years). To ensure that new sanitation systems can inactivate STH, a better understanding of their resilience is required. This study assessed the inactivation of Ascaris eggs under various conditions, in terms of moisture content (MC) (<20 to >90%), temperature (20-50 °C) and pH (7-12.5). The results highlight that the exposure of Ascaris eggs to elevated pH (10.5-12.5) at temperatures ≤27.5 °C for >70 days had no effect on egg viability. Compounding effects of alkaline pH (≥10.5) or decreasing MC (<20%) was observed at 35 °C, with pH having more of an effect than decreasing MC. To accelerate the inactivation of STH, an increase in the treatment temperature is more effective than pH increase. Alkaline pH alone did not inactivate the eggs but can enhance the effect of ammonia, which is likely to be present in organic wastes.

Pathogen Reduction Potential in Anaerobic Digestion of Organic Fraction of Municipal Solid Waste and Food Waste

Anaerobic digestion (AD) is a commonly used method of processing waste. Regardless of the type of the used digestate (fertilizer, feedstock in case of solid-state fermentation, raw-material in case of thermal treatment) effective pathogen risk elimination, even in the case of high pathogen concentration is essential. An investigation of the survival time and inactivation rate of the Salmonella Senftenberg W₇₇₅, Enterococcus spp., and Ascaris suum eggs during thermophilic anaerobic digestion performed on laboratory scale and confirmation of hygienization in full-scale operation were performed in this study. Except for sanitization efficiency, the AD process performance and stability were also verified based on determination of pH value, dry matter content, acidity, alkalinity, and content of fatty acids. The elimination of pathogen was met within 6.06 h, 5.5 h, and about 10 h for the Salmonella Senftenberg W₇₇₅, Enterococcus spp., and Ascaris suum, respectively in the laboratory trials. The obtained results were confirmed in full-scale tests, using 1500 m³ Kompogas^® reactors, operating in MBT Plant located in Poland. Sanitization of the digestate was achieved. Furthermore, the process was stable. The pH value, suspended solids, and ammonium content remained stable at 8.5, 35%, and 3.8 g/kg, respectively. The acetic acid content was noted between almost 0.8 and over 1.1 g/kg, while the concentration of propionic acid was noted at maximum level of about 100 mg/kg. The AD conditions could positively affect the pathogen elimination. Based on these results it can be found that anaerobic digestion under thermophilic conditions results in high sanitation efficiency.

Current time-temperature relationships for thermal inactivation of Ascaris eggs at mesophilic temperatures are too conservative and may hamper development of simple, but effective sanitation

Ascaris eggs are commonly used as indicators for pathogen inactivation during the treatment of fecal sludge and wastewater due to their highly resistant lipid membrane and ability to survive in the environment for long periods of time. Current guidelines suggest that thermal treatment alone cannot inactivate Ascaris eggs at temperatures below 45 °C, although some evidence in the literature suggests this to be incorrect. Here, we performed a controlled experiment to test the effect of mesophilic temperatures on Ascaris inactivation. We exposed Ascaris suum eggs to a temperature gradient between 34°C and 45 °C under anaerobic and aerobic conditions to observe the required exposure times for a 3-log reduction. Indeed, we found that temperatures lower than 45 °C did inactivate these eggs, and the required exposure times were up to two orders of magnitude shorter than suggested by current guidelines. Results from the anaerobic exposures were used to develop a time-temperature relationship that is appropriate for Ascaris inactivation at mesophilic temperatures. Data from the literature demonstrated that our relationship is conservative, with faster inactivation occurring under environmental conditions when Ascaris eggs were suspended in fecal sludge or manure. A specific aerobic relationship was not developed, but we demonstrated that aerobic conditions cause faster inactivation than anaerobic conditions. Therefore, the anaerobic relationship provides a conservative guideline for both conditions. We demonstrate that relatively low temperatures can considerably impact Ascaris viability and suggest that mesophilic temperatures can be used in waste treatment processes to inactivate pathogens. The development of safe, low-input, mesophilic treatment processes is particularly valuable for ensuring universal access to safe sanitation and excreta management.