Removal of p-aminobenzenesulfanilamide from water solutions by catalytic photo-oxidation over Fe-pillared clay

Fe-pillared montmorillonite functionalized chitosan/gelatin foams for efficient removal of organic pollutants by integration of adsorption and Fenton degradation

A Fe-pillared montmorillonite (Fe-MMT) functionalized bio-based foam (Fe-MMT@CS/G) was developed by using chitosan (CS) and gelatin (G) as the matrix for high-efficiency elimination of organic pollutants through the integration of adsorption and Fenton degradation. The results showed that the mechanical properties of as-obtained foam were strengthened by the addition of certain amounts of Fe-MMT. Interestingly, Fe-MMT@CS/G displayed efficient adsorption ability for charged pollutants under a wide range of pH. The adsorption processes of methyl blue (MB), methylene blue (MEB) and tetracycline hydrochloride (TCH) on Fe-MMT@CS/G were well described by the Freundlich isotherm model and pseudo-second-order kinetic model. The maximum adsorption capacities were 2208.24 mg/g for MB, 1167.52 mg/g for MEB, and 806.31 mg/g for TCH. Electrostatic interactions, hydrogen bonding and van der Waals forces probably involved the adsorption process. As expected, this foam could exhibit better removal properties toward both charged and uncharged organic pollutants through the addition of H2O2 to trigger the Fenton degradation reaction. For non-adsorbable and uncharged bisphenol A (BPA), the removal efficiency was dramatically increased from 1.20 % to 92.77 % after Fenton degradation. Additionally, it presented outstanding recyclability. These results suggest that Fe-MMT@CS/G foam is a sustainable and efficient green material for the alleviation of water pollution.

A review of the influence of soil minerals and organic matter on the migration and transformation of sulfonamides

Sulfonamides (SAs) are common antibiotics that are widely present in the environment and can easily migrate in the environment, so they pose an environmental risk. Minerals and organic matter influence the antibiotic migration and transformation in sewage treatment plants, activated sludge, surface water, and soil environment. In the present paper, the influence of the process and mechanism of minerals and organic matter on the adsorption, degradation, and plant uptake of SAs in soil were summarized. In the impact process of mineral and organic matter on the SAs migration and transformation, the pH value is undoubtedly the most important factor because it determines the ionic state of SAs. In terms of influence mechanisms, the minerals absorb SAs well via cation exchange, complexation, H-bonding, and cation bridging. Mineral photodegradation is also one of the primary removal methods for SAs. Soil organic matter (SOM) can significantly increase the SAs adsorption. The adsorption forces of SAs and SOM or dissolved organic matter (DOM) were very similar, but SOM decreased SAs mobility in the environment, while DOM increased SAs availability. DOM generated active substances and aided in the photodegradation of SAs. This review describes the effects of minerals and organic matter on the fate of SAs in soil, which is useful in controlling the migration and transformation of SAs in the soil environment.

Efficient photocatalytic degradation of emerging ciprofloxacin under visible light irradiation using BiOBr/carbon quantum dot/saponite composite

The use of visible-driven photocatalysts has fascinated attention as a capable and sustainable approach for wastewater remediation. In this work, BiOBr/carbon quantum dot (CQDs)/saponite composites (CQDs/Clay@BiOBr) were fabricated via hydrothermally using two different CQDs/Clay precursors (in-situ synthesis (IS) and physical mixing (PM)). The obtained products were characterized, and the photocatalytic performances of the prepared samples were evaluated in the photocatalytic decomposition of emerging ciprofloxacin (CIP) pharmaceutical waste. The highest CIP mineralization performance was achieved when a combination of BiOBr and CQDs/Clay (IS) with the appropriate proportion because the strong adhesion between CQDs and clay generate a great heterojunction in the composite. The stronger interaction of CQDs and better distribution of CQDs on the surface of clay in the CQDs/Clay (IS) enhanced the interaction of BiOBr and CQDs, and avoided the re-agglomeration of excess of CQDs on surface of BiOBr which reduce the active surface to receive the light and react with CIP. The ultrafast degradation rate of the optimized CQDs/Clay@BiOBr composite was better compared to others. The significant improvement in the CIP degradation efficiency of the CQDs/Clay@BiOBr composite was attributed to the excellent separation and transportation of photogenerated electrons and holes, as confirmed by photoluminescence, photocurrent density, and electrochemical impedance spectroscopy results. Moreover, the photocatalytic degradation mechanism of CIP in the CQDs/Clay@BiOBr composite was proposed based on the electronic states of each material in the composite and on a scavenger test. Thus, the proposed CQDs/Clay@BiOBr composite can be employed as a potential visible-light-driven photocatalyst for the decomposition of organic contaminants in wastewater.

Research Trends on Pillared Interlayered Clays (PILCs) Used as Catalysts in Environmental and Chemical Processes: Bibliometric Analysis

Over the last four decades, a large number of studies have been published on pillared interlayered clays (PILCs) used as adsorbent materials and catalysts or supports for transition metals in heterogeneous catalysis. Particularly, PILCs have been used for water treatment through advanced oxidation processes (AOPs) to remove organic pollutants. They have also been studied in various chemical and environmental processes. Because of the growing interest in PILCs, this article is focused on analyzing scientific publications such as research/review articles and book chapters from the last four decades (from 1980 to 2019) through a bibliometric analysis (BA) to visualize and describe research trends on PILCs. By narrowing the bibliographic search to titles, keywords, and abstracts of publications related to PILCs, using Scopus and Web of Science (WoS) (the two scientific databases), a total of 3425 documents have been retrieved. The bibliometric dataset was analyzed by VantagePoint^®. The main research trends identified in the last four decades were the use of PILCs in environmental processes (34.4% of total publications) along with chemical processes (petrochemical reactions 17.5%, SCR NOx 10.8%, and decomposition 8.2%). In environmental processes, PILCs have been used in photo-oxidation (32%), CWPO (21.1%), and heterogeneous catalysis (19.4%). Phenols, dyes, and VOCs have been the main pollutants studied using PILCs as catalysts. Fe, Ti, Zr, Cu, and Co are the most supported active phases in PILCs. Other research trends grouped by characterization techniques, countries, research areas, institutes, scientific journals that have published the most on this topic, number of publications per 5-year period, and most frequently used keywords through the last four decades have been identified. It was determined that the number of publications on PILCs has increased since 1980 and the countries with the highest number of publications are China, Spain, and The United States of America.

Guidelines to Study the Adsorption of Pesticides onto Clay Minerals Aiming at a Straightforward Evaluation of Their Removal Performance

Natural and modified clay minerals have been extensively used for the adsorption/desorption of organic substances, especially pesticides, from waters and wastewater, aiming at pollution control and more efficient use of the herbicides through controlled release. While natural clay minerals efficiently remove organic cations such as paraquat and diquat, the adsorption of anionic or neutral species demands surface chemical modification with, for instance, quaternary ammonium salts containing long alkyl chains. Basic pesticides, on the other hand, are better absorbed in clay minerals modified with polycations. Kinetic studies and adsorption/desorption isotherms provide the parameters needed to evaluate the clay mineral’s adsorptive performance towards the pollutant target. However, the direct comparison of these parameters is complicated because the experimental conditions, the analytical techniques, the kinetic and isotherm models, and the numerical fitting method differ among the various studies. The free-energy-related Langmuir constant depends on the degree of site occupation; that is, it depends on the concentration window used to construct the adsorption isotherm and, consequently, on the analytical technique used to quantify the free concentrations. This paper reviews pesticides’ adsorption on natural and modified clay minerals and proposes guidelines for designing batch adsorption/desorption studies to obtain easily comparable and meaningful adsorption parameters. Articles should clearly describe the experimental conditions such as temperature, contact time, total concentration window, the solution to adsorbent ratio, the analytical technique, and its detection and quantification limits, besides the fitting models. Research should also evaluate the competitive effects of humic substances, colloidal inorganic particles, and ionic strength to emulate real-world adsorption experiments.

Fenton-like degradation of sulfathiazole using copper-modified MgFe-CO3 layered double hydroxide

The catalytic activity of layered double hydroxides, with and without insertion of copper, was evaluated in a heterogeneous Fenton process for degradation of the antibiotic sulfathiazole (STZ). The characterizations with different techniques revealed lamellar structures formed by stacking of layers containing magnesium, iron, and copper cations. The insertion of copper in the lamellar structure increased the specific area of the material and the degradation kinetics, achieving complete STZ removal after 90 min. X-ray photoelectron spectroscopy analysis showed the presence of Cu(II) and Cu(I) surface sites, which contributed to the generation of hydroxyl and hydroperoxyl/superoxide radicals. It also indicated an increase of Cu(I) content after use. For both materials, but specially for LDH without copper, addition of tert-butyl alcohol and p-benzoquinone hindered STZ degradation, indicating the importance of hydroxyl and hydroperoxyl/superoxide radicals in the degradation process, respectively. These results demonstrated the potential of copper-modified MgFe-CO₃ as a catalyst for the degradation of emerging contaminants, offering the benefits of easy preparation and high efficiency in the Fenton process.

Visible-Light Enhanced Catalytic Wet Peroxide Oxidation of Natural Organic Matter in the Presence of Al/Fe-Pillared Clay

An Al/Fe-pillared clay catalyst (Al/Fe-PILC) prepared from low cost technical-grade reagents has been investigated in the photocatalytic Wet Peroxide Oxidation (photo-CWPO) of dissolved Natural Organic Matter (NOM) under circumneutral pH. The successful pillaring of the layered clay material was confirmed by X-ray diffraction (XRD), N2 adsorption at −196 °C, cation exchange capacity (CEC) and simultaneous thermal analysis (TGA/DSC). High levels of mineralization of the dissolved organic carbon and color removal of a synthetic NOM surrogate solution were achieved even under natural lab’s lighting and ambient temperature and pressure, whereas the absence of radiation (in dark) was found to strongly affect the performance of the degradation. The photo-CWPO of NOM activated by the Al/Fe-PILC clay catalyst under visible light irradiation (LED lamp, 450 and 550 nm peaks) displayed a DOC mineralization of 72% and color removal of 73% in just 210 min of irradiation at neutral pH, whereas both responses decayed under ultraviolet lightning (λ: 365 nm) to 41% and 58%, respectively. This behavior is ascribed to formation of triplet states of natural organic matter (3NOM*) by absorption of visible light, which seems to synergistically improve the rate-determining step of the heterogeneous Fenton process, namely reduction of Fe3+ into Fe2+ on the surface of the clay catalyst. Interestingly, experiments performed at neutral and pH 3.0 showed very similar efficiencies under visible light irradiation; these findings may really facilitate the application of the photo-CWPO process to assist conventional drinking water treatment plants in the removal of NOM before the typical disinfection by chlorine to produce safer drinking water.