C1 Lateral Mass Screw Placement Through Endonasal Corridor for Purpose of O-C1 Fusion: Morphometric Analysis in Cadaveric Specimens

Endoscopic Endonasal Occipitocervical Fixation with a Customized Three-Dimensional Printed Titanium Plate-Screw Construct: A Cadaveric Feasibility Study

OBJECTIVE

To evaluate the feasibility of a novel method for occipitocervical fixation (OCF) through the endonasal corridor.

METHODS

Thin-cut computed tomography scans were obtained for 5 cadaveric specimens. Image segmentation was used to reconstruct 3D models of each O-C1 joint complex. Using computer-aided design software, plates were custom-designed to span each O-C1 joint, sit flush onto the bony surface, and accommodate screws. The final models were 3D-printed in titanium. For implantation, specimens were held in pin-fixation and registered to neuronavigation. A rigid 0º endoscope was used for endonasal visualization. An inverted U-shaped nasopharyngeal flap was raised to expose the occipital condyles and C1. The plates were introduced and fixed with bone screws. Computed tomography scans were obtained to assess screw accuracy and proximity to critical neurovascular structures. Screw entry points and trajectories were recorded.

RESULTS

Endonasal OCF was performed on 5 cadaveric specimens. The mean starting point for occipital condyle screws was 6.17 mm lateral and 5.38 mm rostral to the medial O-C1 joint. Mean axial and sagittal trajectories were 7.98° and 6.71°, respectively. The mean starting point for C1 screws was 16.11 mm lateral to the C1 anterior tubercle and 6.39 mm caudal to the medial O-C1 joint. Mean axial and sagittal trajectories were 10.97° and -9.91°, respectively.

CONCLUSIONS

Endonasal OCF is technically and anatomically feasible. The application of this technique may allow for same-stage endonasal decompression and fixation, offering a minimally invasive alternative to current methods of fixation and advancing surgeons' ability to treat pathology of the craniovertebral junction. Next steps will focus on biomechanical testing.

Anterior occipital condyle screw placement through the endonasal corridor: proof of concept study with cadaveric analysis

PURPOSE

Odontoidectomy for ventral compressive pathology may result in O-C1 and/or C1-2 instability. Same-stage endonasal C1-2 spinal fusion has been advocated to eliminate risks associated with separate-stage posterior approaches. While endonasal methods for C1 instrumentation and C1-2 trans-articular stabilization exist, no hypothetical construct for endonasal occipital instrumentation has been validated. We provide an anatomic description of anterior occipital condyle (AOC) screw endonasal placement as proof-of-concept for endonasal craniocervical stabilization.

METHODS

Eight adult, injected cadaveric heads were studied for placing 16 AOC screws endonasally. Thin-cut CT was used for registration. After turning a standard inferior U-shaped nasopharyngeal flap endonasally, 4 mm × 22 mm AOC screws were placed with a 0° driver using neuronavigation. Post-placement CT scans were obtained to determine: site-of-entry, measured from the endonasal projection of the medial O-C1 joint; screw angulation in sagittal and axial planes, proximity to critical structures.

RESULTS

Average site-of-entry was 6.88 mm lateral and 9.74 mm rostral to the medial O-C1 joint. Average angulation in the sagittal plane was 0.16° inferior to the palatal line. Average angulation in the axial plane was 23.97° lateral to midline. Average minimum screw distances from the jugular bulb and hypoglossal canal were 4.80 mm and 1.55 mm.

CONCLUSION

Endonasal placement of AOC screws is feasible using a 0° driver. Our measurements provide useful parameters to guide optimal placement. Given proximity of hypoglossal canal and jugular bulb, neuronavigation is recommended. Biomechanical studies will ultimately be necessary to evaluate the strength of AOC screws with plate-screw constructs utilizing endonasal C1 lateral mass or C1-2 trans-articular screws as inferior fixation points.