Role of Surface Characteristics of Mannitol in Crystallization of Fenofibrate During Spray Drying

Enhanced dissolution rates of glibenclamide through solid dispersions on microcrystalline cellulose and mannitol, combined with phosphatidylcholine

OBJECTIVE

This study aimed to investigate the impact of physical solid dispersions of spray-dried glibenclamide (SG) on the surface of microcrystalline cellulose (MC) and mannitol (M) surfaces, as well as their combination with phosphatidylcholine (P), on enhancing the dissolution rate of glibenclamide (G).

METHODS

Solid dispersions were prepared using varying proportions of 1:1, 1:4, and 1:10 for SG on the surface of MC (SGA) and M (SGM), and then combined with P, in a proportion of 1:4:0.02 using spray drying. The particle size, specific surface area, scanning electron microscopy (SEM), X-ray diffraction (XRD), and dissolution rate of SGA and SGM were characterized.

RESULTS

SEM analysis revealed successful adhesion of SG onto the surface of the carrier surfaces. XRD showed reduced crystalline characteristic peaks for SGA, while SGM exhibited a sharp peaks pattern. Both SGA and SGM demonstrated higher dissolution rates compared to SG and G alone. Furthermore, the dissolution rates of the solid dispersions of SG, MC and P (SGAP), and SG, M, and P (SGMP) were sequentially higher than that of SGA and SGM.

CONCLUSIONS

The study suggests that physical solid dispersions of SG on MC and M, along with their combination with P, can effectively enhance the dissolution rate of G. These findings may be valuable in developing of oral solid drug dosage forms utilizing SGA, SGM, SGAP, and SGMP.

Sugars and Polyols of Natural Origin as Carriers for Solubility and Dissolution Enhancement

Crystalline carriers such as dextrose, sucrose, galactose, mannitol, sorbitol, and isomalt have been reported to increase the solubility, and dissolution rates of poorly soluble drugs when employed as carriers in solid dispersions (SDs). However, synthetic polymers dominate the preparation of drugs: excipient SDs have been created in recent years, but these polymer-based SDs exhibit the major drawback of recrystallisation upon storage. Also, the use of high-molecular-weight polymers with increased chain lengths brings forth problems such as increased viscosity and unnecessary bulkiness in the resulting dosage form. An ideal SD carrier should be hydrophilic, non-hygroscopic, have high hydrogen-bonding propensity, have a high glass transition temperature (Tg), and be safe to use. This review discusses sugars and polyols as suitable carriers for SDs, as they possess several ideal characteristics. Recently, the use of low-molecular-weight excipients has gained much interest in developing SDs. However, there are limited options available for safe, low molecular excipients, which opens the door again for sugars and polyols. The major points of this review focus on the successes and failures of employing sugars and polyols in the preparation of SDs in the past, recent advances, and potential future applications for the solubility enhancement of poorly water-soluble drugs.

Analytical and Computational Methods for the Determination of Drug-Polymer Solubility and Miscibility

In the pharmaceutical industry, poorly water-soluble drugs require enabling technologies to increase apparent solubility in the biological environment. Amorphous solid dispersion (ASD) has emerged as an attractive strategy that has been used to market more than 20 oral pharmaceutical products. The amorphous form is inherently unstable and exhibits phase separation and crystallization during shelf life storage. Polymers stabilize the amorphous drug by antiplasticization, reducing molecular mobility, reducing chemical potential of drug, and increasing glass transition temperature in ASD. Here, drug-polymer miscibility is an important contributor to the physical stability of ASDs. The current Review discusses the basics of drug-polymer interactions with the major focus on the methods for the evaluation of solubility and miscibility of the drug in the polymer. Methods for the evaluation of drug-polymer solubility and miscibility have been classified as thermal, spectroscopic, microscopic, solid-liquid equilibrium-based, rheological, and computational methods. Thermal methods have been commonly used to determine the solubility of the drug in the polymer, while other methods provide qualitative information about drug-polymer miscibility. Despite advancements, the majority of these methods are still inadequate to provide the value of drug-polymer miscibility at room temperature. There is still a need for methods that can accurately determine drug-polymer miscibility at pharmaceutically relevant temperatures.

Development of a naftopidil-chitosan-based fumaric acid solid dispersion to improve the dissolution rate and stability of naftopidil

Naftopidil (NAF), an α₁-adrenoceptor antagonist, is administered as a treatment for benign prostatic hyperplasia; however, according to the Biopharmaceutical Classification System (BCS IV), it is a poorly-soluble drug that exhibits poor permeability. We aimed to increase the dissolution (%) of NAF by adding chitosan to a polymer-free formulation. Compared to the formulation prepared using Flivas®, at 60 min, the solid dispersion (SD) formulation containing NAF, fumaric acid, chitosan, and US2® in a 1:1:2:1 weight ratio improved the dissolution (%) of NAF in distilled water, pH 1.2 media, pH 4.0 and pH 6.8 buffers by 27.2-, 1.2-, 1.1- and 6.5-fold, respectively. The physicochemical properties of the SD1 formulation were also found to be altered, including its thermal properties, crystal intensity, and chemical interaction. As a result, the hydrogen bonding that occurs between NAF and fumaric acid was identified as a major factor in the increase in NAF dissolution (%). Further, chitosan was observed to contribute to the stability of NAF and SD1, which was assessed over a 3-month period. To our knowledge, this is the first study to employ a polymer-free system to improve the solubilization of NAF.

Solubilization of tadalafil using a tartaric acid and chitosan-based multi-system

Solubilization studies of tadalafil (TDF) have recently improved the dissolution (%) using weak acids and bases in our group. However, the weak acid formulations have a low dissolution (%) of TDF as limitation. Thus, the purpose of this study was to improve the dissolution (%) of TDF over 90% in distilled water (DW) by weak acid-chitosan based multi-system. The SD formulation (SD11: TDF, tartaric acid, chitosan, Aerosil®200, and PVP/VA S-630 in a 1:2:1:1:2 weight ratio) showed higher dissolution (%) of TDF by 5.0-, 6.0-, and 5.8-fold at 60 min than that of Cialis® in DW and pH 1.2 and pH 6.8 buffers, respectively. The physical properties of the SD11 formulation were changed. Moreover, the SD11 formulation maintained stability for 3 months. In conclusion, the solubilization of TDF using chitosan was successfully performed for the first time.