Direct titrations of antibiotics with iodate solution

Galvanostatic entrapment of penicillinase into polytyramine films and its utilization for the potentiometric determination of penicillin

A sensitive and reliable potentiometric biosensor for determination of penicillin has been developed by exploiting the self-limiting growth of the non-conducting polymer, polytyramine. Optimum polytyramine-penicillinase (PTy-PNCnase) films for potentiometric detection of penicillin were accomplished with monomer solutions which contained 0.03 M tyramine, 37 U/mL penicillinase, 0.01 M KNO₃, and 3 mM penicillin with an applied current density of 0.8 mA/cm² and an electropolymerisation time of 40 seconds. The potentiometric biosensor gave a linear concentration range of 3–283 μM for penicillin and achieved a minimum detectable concentration of 0.3 μM. The biosensor was successfully utilized for the detection of Amoxycillin and gave an average percentage recovery of 102 ± 6%. Satisfactory recoveries of penicillin G were also achieved in milk samples with the potentiometric biosensor when concentrations are ≥20 ppm.

Validation of simultaneous volumetric and spectrophotometric methods for the determination of captopril in pharmaceutical formulations

Simple, sensitive and economical simultaneous volumetric and spectrophotometric methods for the determination of captopril have been developed. The methods were based on the reaction of captopril with potassium iodate in HCl medium. Amaranth was used as indicator to detect the end-point of the titration in aqueous layer. The iodine formed during the titration was extracted into CCl4 and subsequently determined spectrophotometrically at 510 nm. The Beer's law was obeyed in the concentration range of 120-520 microg ml-1. Rigorous statistical analyses were performed for the validation of the proposed methods. The proposed methods were successfully applied to the determination of captopril in dosage forms. Comparison of the means of the proposed procedures with those of reference methods using point and interval hypothesis tests showed no statistically significant difference.

Simultaneous determination of carvedilol and ampicillin sodium by synchronous fluorimetry

The carvedilol and ampicillin sodium were simultaneously determined by the synchronous fluorimetry. With excitation wavelength at 254 nm, the maximum emission wavelengths of carvedilol and ampicillin sodium were at 357 and 426 nm, respectively. Because the emission spectra of carvedilol and ampicillin sodium were overlapped partially, carvedilol and ampicillin sodium cannot be determined directly by normal fluorimetric method. However, the synchronous fluorimetry can be used for determining both drugs simultaneously without separation procedure. The (Delta)(lambda) = 80 nm was used. Iso-propanol was selected as sensing reagent. Effects of pH, organic solvents and foreign ions on the determination of both drugs were studied. The linear relationship was obtained between the relative fluorescence intensity and concentration of carvedilol and ampicillin sodium in the range of 0.005-0.1 and 5.0-70.0 microg ml(-1), respectively. The linear regression equation of calibration graph for carvedilol is C = 0.000151F - 0.00210, and for ampicillin sodium is C = 0.0770F - 2.62. The correlation coefficient of linear regression equation is 0.9995 for carvedilol and 0.9998 for ampicillin sodium, respectively. The detection limit is 1 ng ml(-1) for carvedilol and 1 microg ml(-1) for ampicillin sodium. The relative standard deviations of carvidelol and ampicillin sodium are 2.47 and 1.61%, respectively. The recovery is from 96.0 to 103.0% for carcvedilol and from 98.0 to 105.0% for ampicillin sodium. This method was rapid, simple and highly sensitive for the determination of carvedilol and ampicillin sodium without pre-separation. The results obtained by this method agreed with those by the official methods. This method can be used for the determination of carvedilol and ampicillin sodium in the medicine dosage.

Simultaneous Determination of Carvedilol and Ampicillin Sodium by First-Derivative Fluorometry in the Presence of Human Serum Albumin

A sensitive and selective method for the simultaneous determination of carvedilol and ampicillin sodium (AS) in the presence of human serum albumin (HSA) is described. The maximum emission wavelengths of carvedilol and AS are at 357 nm and 426 nm with excitation at 254 nm, respectively. The first-derivative peaks of carvedilol and AS were at 337 nm and 398 nm, respectively. The linear-regression equations of the calibration graphs of carvedilol and AS were C = 0.0001H - 0.0063 and C = 1.530H - 43.84; the correlation coefficients were 0.9990 and 0.9986, respectively. The detection limits were 1 ng ml(-1) for carvedilol and 23 microg ml(-1) for AS, respectively. The effects of the pH, the stability of carvedilol and AS and foreign ions on the determination of carvedilol and AS were examined. The recoveries of carvedilol and AS were measured. This method is simple and can be used for the determination of carvedilol and AS in human serum and urine samples with satisfactory results.

Simultaneous spectrophotometric and volumetric determinations of amoxycillin, ampicillin and cloxacillin in drug formulations: reaction mechanism in the base catalysed hydrolysis followed by oxidation with iodate in dilute acid solution

A method for the analysis of degraded products of amoxycillin, ampicillin and cloxacillin in drug formulations, obtained as a result of their base hydrolysis is described. Simultaneous spectrophotometric and volumetric determinations of the antibiotic is based on the neutralization of the degraded product by dilute hydrochloric acid to get a pH approximately 2 to be conducive for redox titration using potassium iodate as titrant. A red purple colour is developed in carbon tetrachloride at the end point. Spectrophotometry is done after separating the organic layer and measuring the absorbance of red-purple colour at lambda(max) 520 nm. The pathways of different degraded products and their oxidation mechanism is described on IR, TLC and UV spectroscopic studies.

Penicillins and cephalosporins. Physicochemical properties and analysis in pharmaceutical and biological matrices

Penicillins and cephalosporins belong to the most prescribed antibiotics. Despite the relatively extended knowledge of these drugs, the qualitative and quantitative analysis of the compounds still gives rise to many problems. These difficulties are due to the chemical instability of the common beta-lactam nucleus, the minor differences in chemical structures between the analogues, and the complex and relatively fast degradation of the compounds in aqueous solutions. In this review a compilation of the physicochemical properties, the degradation routes and methods for analysis of these substances in biological and other matrices is presented.

Application of Azure C for the extractive spectrophotometric determination of microgram amounts of penicillin

A simple, accurate, and rapid method for the quantitative determination of penicillin is proposed. The method is based on the formation of a blue penicillin-Azure-C ion-pair that can be extracted into chloroform in phosphate-citric acid buffer. The molar absorptivities for sodium penicillin G and potassium penicillin V at 635 nm were 5.46 X 10(3) and 2.19 X 10(4) l/mol/cm, respectively. Beer's law was valid over the concentration range of 4-80 micrograms/ml for sodium penicillin G and 3-55 micrograms/ml for potassium penicillin v. Maximum absorbance was obtained almost instantaneously and was stable for several days. The method was successfully applied to pharmaceutical preparations.