Development of an amperometric biosensor based on glutathione peroxidase immobilized in a carbodiimide matrix for the analysis of reduced glutathione from serum

Carbon Electrode-Based Biosensing Enabled by Biocompatible Surface Modification with DNA and Proteins

Modification of electrodes with biomolecules is an essential first step for the development of bioelectrochemical systems, which are used in a variety of applications ranging from sensors to fuel cells. Gold is often used because of its ease of modification with thiolated biomolecules, but carbon screen-printed electrodes (SPEs) are gaining popularity due to their low cost and fabrication from abundant resources. However, their effective modification with biomolecules remains a challenge; the majority of work to-date relies on nonspecific adhesion or broad amide bond formation to chemical handles on the electrode surface. By combining facile electrochemical modification to add an aniline handle to electrodes with a specific and biocompatible oxidative coupling reaction, we can readily modify carbon electrodes with a variety of biomolecules. Importantly, both proteins and DNA maintain bioactive conformations following coupling. We have then used biomolecule-modified electrodes to generate microbial monolayers through DNA-directed immobilization. This work provides an easy, general strategy to modify inexpensive carbon electrodes, significantly expanding their potential as bioelectrochemical systems.

Characteristics of P-Type and N-Type Photoelectrochemical Biosensors: A Case Study for Esophageal Cancer Detection

P-type and N-type photoelectrochemical (PEC) biosensors were established in the laboratory to discuss the correlation between characteristic substances and photoactive material properties through the photogenerated charge carrier transport mechanism. Four types of human esophageal cancer cells (ECCs) were analyzed without requiring additional bias voltage. Photoelectrical characteristics were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), UV–vis reflectance spectroscopy, and photocurrent response analyses. Results showed that smaller photocurrent was measured in cases with advanced cancer stages. Glutathione (L-glutathione reduced, GSH) and Glutathione disulfide (GSSG) in cancer cells carry out redox reactions during carrier separation, which changes the photocurrent. The sensor can identify ECC stages with a certain level of photoelectrochemical response. The detection error can be optimized by adjusting the number of cells, and the detection time of about 5 min allowed repeated measurement.

Transdermal patches loaded with L-cysteine HCL as a strategy for protection from mobile phone emitting electromagnetic radiation hazards

Mobile phone usage has been increased in the last few years emitting electromagnetic radiation (EMR), which disturbs normal cellular processes via oxidative stress. L-cysteine, a glutathione precursor, prevents oxidative damage. Transdermal patches (TDPs) loaded with L-cysteine hydrochloride (L-CyS-HCL) were fabricated by dispersion of L-CyS-HCL 5% w/w and different concentrations of sorbitol as a plasticizer in room-temperature vulcanizable synthetic silicone matrices (RTV-Si). The effect of sorbitol on patch physicochemical parameters was assessed; in-vitro L-CyS-HCL release profiles and ex-vivo permeation were studied. Pharmacokinetic parameters of endogenous synthetized in-vivo glutathione, after receiving IV bolus dose of L-CyS-HCl and L-CyS-HCl-RTV-Si-TDPs were studied in rat model. The influence of L-CyS-HCL-RTV-Si-TDPs against damaging effects of mobile phone EMR on rats' blood and brain tissues was studied. The results revealed that patch plasticity, intensity reflections, surface porosity, L-CyS-HCL release rate and skin permeation increased with increasing sorbitol concentration. Pharmacokinetic profile for IV dose and L-CyS-HCl-RTV-Si-TDPs revealed that the L-CyS-HCl-RTV-Si-TDPs provided a sustained glutathione plasma concentration-time profile over entire patch application. High significant differences in biological parameters (blood and brain samples) were observed for radiated rats using the patch in study compared with positive control rats. Promising long-term strategy for protection against mobile phone hazards was obtained.

Evaluation of the reactivity of exhaust from various biodiesel blends as a measure of possible oxidative effects: A concern for human exposure

Diesel exhaust particles (DEP) are a major constituent of ambient air pollution and are associated with various adverse health effects, posing a major safety and public health concern in ambient and occupational environments. The effects of DEP from various biodiesel blends on biological systems was investigated using glutathione (GSH) as a marker of possible oxidative effects, based on the decrease in the concentration of GSH at physiological pH. The fluorophoric agent 2,3-naphthalenedicarboxaldehyde (NDA) was used as a selective probe of GSH in the presence of any likely interferents via fluorescence detection. Three different polar solvents (acetonitrile, methanol and water) were used to extract DEP generated during the combustion of different biodiesel blends (5%-99%). Oxidation of GSH to the disulfide (GSSG) was confirmed using electrospray ionization mass spectrometry. A decrease in the concentration of GSH was observed in the presence of DEP extracts from all of the biodiesel blends studied, with reaction rates that depend on the biodiesel blend. Interestingly the reactivity peaked at 50% biodiesel (B50) rather than decreasing monotonically with increased biodiesel content, as was expected. Organic solvent DEP extracts showed wider variations in reactivity with GSH, with methanol extracts giving the largest decrease in GSH concentrations. This may imply a more organic nature of the oxidants in the biodiesel exhaust. It is therefore important to consider ways of reducing concentrations of organic components in biodiesel exhaust that can cause different toxic activity before any blend is offered as a preferred alternative to petroleum diesel fuel.

Halogen mediated voltammetric oxidation of biological thiols and disulfides

The electrochemical generation of the halides, bromine and iodine, in the presence of biologically relevant organosulfur is demonstrated to result in an analytically useful response. In the case of the iodide/iodine redox couple only the thiol causes an increase in the electrochemical oxidative peak current. Conversely, the formed bromine may catalytically oxidise both thiols and disulfides. Hence, the differing reactivities of the halide ions readily allow discrimination between the closely related thiol and disulphide species. For all of the organosulfur species investigated (glutathione, cysteine and homocysteine) micromolar limits of detection are attainable. In the case of the bromine mediated oxidation this sensitivity at least partially arises from the large catalytic amplification, such that, for each disulphide molecule up to ten electrons may be transferred. Ultimately this bromine oxidation results in the formation of the sulfonate species. For the iodine mediated oxidation of the thiols the oxidation proceeds no further than to the formation of the associated disulfide.

Colorimetric detection of glutathione based on transverse overgrowth of high aspect ratio gold nanorods investigated by MCR-ALS

In this paper, we present a simple platform for colorimetric detection of glutathione using gold nanorods (AR ∼ 6.5 ± 0.2) as a plasmonic sensor.

A high sensitive electrochemical nanosensor for simultaneous determination of glutathione, NADH and folic acid

In the present study, we report electrosynthesis of 4,5-bis(4-chloroanilino)-1,2-benzendiol (BCB) and its application as a selective electrochemical mediator at a surface of carbon paste electrode (CPE) modified ZnO/CNTs nanocomposite as a simple and rapid voltammetric sensor. The sensor showed an efficient catalytic activity for the electro-oxidation of glutathione (GSH), which leads to a lowered overpotential by more than 203 mV compared to unmodified carbon paste electrode. For the mixture containing GSH, nicotinamide adenine dinucleotide (NADH) and folic acid (FA), the electrooxidation signals were well separated. The square wave voltammetry (SWV) currents increased linearly with their concentration at the ranges of 0.006-161, 1.0-650 and 3.0-700 μM, respectively with the detection limits of 0.002, 0.3 and 1.0 μM. Finally, the electrode was successfully applied for the voltammetric determination of analytes in real samples with satisfactory results.

Synthesis and application of FePt/CNTs nanocomposite as a sensor and novel amide ligand as a mediator for simultaneous determination of glutathione, nicotinamide adenine dinucleotide and tryptophan

In this study, we report the synthesis and application of a FePt/CNTs nanocomposite as a highly sensitive sensor and novel amide ligand (9,10-dihydro-9,10-ethanoanthracene-11,12-dicarboximido)-4-ethylbenzene-1,2-diol as a mediator for the determination of glutathione (GSH), nicotinamide adenine dinucleotide (NADH) and tryptophan (Trp). The synthesized materials were characterized with different methods such as NMR, IR spectroscopy, TEM, XRD, FESEM, cyclic voltammetry, electrochemical impedance spectroscopy and square wave voltammetry (SWV). The modified electrode exhibited a potent and persistent electron mediating behavior followed by well-separated oxidation peaks of GSH, NADH and Trp. The peak currents were linearly dependent on GSH, NADH and Trp concentrations in the range of 0.08-220, 1.0-400 and 5.0-500 μmol L(-1), with detection limits of 0.05, 0.8 and 1.0 μmol L(-1), respectively. The modified electrode was used for the determination of these compounds in real samples.

A new strategy for the selective determination of glutathione in the presence of nicotinamide adenine dinucleotide (NADH) using a novel modified carbon nanotube paste electrode

A novel electrochemical sensor for the simultaneous determination of glutathione (GSH) and nicotinamide adenine dinucleotide (NADH) is described. The sensor is based on a carbon paste electrode (CPE) modified with benzamide derivative and multiwall carbon nanotubes. This mixture makes a modified electrode that is sensitive for the electrochemical detection of these compounds. Under optimum conditions and at pH 7.0, oxidation of GSH occurs at a potential of about 330 mV less positive than that at an unmodified CPE. The voltammetric peak currents are linearly dependent on GSH and NADH concentrations in the ranges 0.09-300 μmol L(-1) GSH and 5.0-600 μmol L(-1) NADH. The detection limits found for GSH and NADH were 0.05 μmol L(-1) and 1.0 μmol L(-1), respectively. The electrochemical sensor was also used for the determination of GSH in urine, pharmaceutical and hemolysed erythrocyte samples.

Gold nanoparticles in an ionic liquid phase supported in a biopolymeric matrix applied in the development of a rosmarinic acid biosensor

Gold nanoparticles dispersed in 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid (Au-BMI·PF(6)) were supported in chitin (CTN) chemically crosslinked with glyoxal and epichlorohydrin to obtain a new supported ionic liquid phase (SILP) catalyst with high catalytic activity, and providing an excellent environment for enzyme immobilization. This modified biopolymer matrix (Au-BMI·PF(6)-CTN) was used as a support for the immobilization of the enzyme peroxidase (PER) from pea (Pisum sativum), and employed to develop a new biosensor for rosmarinic acid (RA) determination in pharmaceutical samples by square-wave voltammetry. In the presence of hydrogen peroxide, the PER catalyzes the oxidation of RA to the corresponding o-quinone, which is electrochemically reduced at a potential of +0.14 V vs. Ag/AgCl. Under optimized conditions, the resulting peak current increased linearly for the RA concentration range of 0.50 to 23.70 μM with a detection limit of 70.09 nM. The biosensor demonstrated high sensitivity, good repeatability and reproducibility, and long-term stability (15% decrease in response over 120 days). The method was successfully applied to the determination of RA content in pharmaceutical samples, with recovery values being in the range of 98.3 to 106.2%. The efficient analytical performance of the proposed biosensor can be attributed to the effective immobilization of the PER enzyme in the modified CTN matrix, the significant contribution of the high conductivity of the ionic liquid, the facilitation of electron transfer promoted by gold nanoparticles, and the inherent catalytic ability of these materials.

Electrocatalytic activity of 4-nitrophthalonitrile-modified electrode for the l-glutathione detection

The present work describes the substantial electrocatalytic activity of (NC)2C6H3-NHOH/(NC)2C6H3-NO redox couple-modified electrode toward the low voltage detection of l-glutathione (GSH), in neutral medium, at an applied potential of 0.4V versus Ag/AgCl. After optimizing the operational conditions, the sensor provided a linear response range for GSH from 8.0 up to 83.0 micromol L(-1) with sensitivity, detection and quantification limits of 54nA L micromol(-1), 2.7 micromol L(-1) and 8.0 micromol L(-1), respectively. The proposed sensor presented higher sensitivity when compared to other modified electrodes described in the literature and showed a stable response for at least 100 successive determinations. The repeatability of the measurements with the same sensor and different sensors, evaluated in terms of relative standard deviation, were 4.1 and 5.0%, respectively, for n=10. The developed sensor was applied for GSH determination in yeast extract and the results were statistically the same with those obtained by the comparative method described in the literature at a confidence level of 95%.

Electrochemiluminescence sensors for scavengers of hydroxyl radical based on its annihilation in CdSe quantum dots film/peroxide system

This work elucidated the detailed electrochemiluminescence (ECL) process of the thioglycolic acid-capped CdSe quantum dots (QDs) film/peroxide aqueous system. The QDs were first electrochemically reduced to form electrons-injected QDs approximately -1.1 V, which then reduced hydrogen peroxide to produce OH* radical. The intermediate OH* radical was a key species for producing holes-injected QDs. The ECL emission with a peak at -1.114 V was demonstrated to come from the 1Se-1Sh transition emission. Using thiol compounds as the model molecules to annihilate the OH* radical, their quenching effects on ECL emission were studied. This effect led to a novel strategy for ECL sensing of the scavengers of hydroxyl radical. The detection results of thiol compounds showed high sensitivity, good precision, and acceptable accuracy, suggesting the promising application of the proposed method for quick detection of both scavengers and generators of hydroxyl radical in different fields.

Electrocatalytic determination of reduced glutathione in human erythrocytes

The determination of reduced glutathione (GSH) in human erythrocytes using a simple, fast and sensitive method employing a glassy carbon electrode modified with cobalt tetrasulfonated phthalocyanine (CoTSPc) immobilized in poly(L: -lysine) (PLL) film was investigated. This modified electrode showed very efficient electrocatalytic activity for anodic oxidation of GSH, decreasing substantially the anodic overpotentials for 0.2 V versus Ag/AgCl. The modified electrode presented better performance in 0.1 mol l(-1) piperazine-N,N'-bis(2-ethanesulfonic acid) buffer at pH 7.4. The other experimental parameters, such as the concentration of CoTSPc and PLL in the membrane preparation, pH, type of buffer solution and applied potential, were optimized. Under optimized operational conditions, a linear response from 50 to 2,160 nmol l(-1) was obtained with a high sensitivity of 1.5 nA l nmol(-1) cm(-2). The detection limit for GSH determination was 15 nmol l(-1). The proposed sensor presented good repeatability, evaluated in terms of the relative standard deviation (1.5%) for n = 10. The modified electrode was applied for determination of GSH in erythrocyte samples and the results were in agreement with those obtained by a comparative method described in the literature The average recovery for these fortified samples was 100 +/- 1)%. Applying a paired Student's-t test to compare these methods, we could observe that, at the 95% confidence level, there was no statistical difference between the reference and the proposed methods.

Electrocatalytic activity of cobalt phthalocyanine CoPc adsorbed on a graphite electrode for the oxidation of reduced l-glutathione (GSH) and the reduction of its disulfide (GSSG) at physiological pH

Modified electrodes coated by adsorbed cobalt phthalocyanines are known to show substantial electrocatalytic activity for the electro-oxidation of several thiols in alkaline aqueous solution. In this context, we explore in this study the electrocatalytic activity of adsorbed cobalt phthalocyanine (CoPc) on ordinary pyrolytic graphite electrode for the oxidation of reduced L-glutathione GSH and the reduction of its disulfide GSSG at physiological pH. To do so, cyclic and rotating disk voltammetries were performed and the amperometric results show that a stable electrochemical sensing material, with good reproducibility and sensitivity (in accordance with the concentrations of GSH expected in biological media), can be easily achieved. This opens the way for the design of an electrochemical sensor able to detect these two analytes in biologically relevant experimental conditions (in terms of pH).

Determination of glutathione in hemolysed erythrocyte with amperometric sensor based on TTF-TCNQ

BACKGROUND

GSH has a relevant role in human metabolism as an indicator of disease risks. An amperometric sensor for glutathione (GSH) determination is described as an alternative method featuring simple construction procedure and short time analysis.

METHOD

The developed sensor was used to determine glutathione at low potential using a TTF-TCNQ complex.

RESULTS

The sensor exhibits a linear response range from 5 to 340 micromol/l under applied potential of 200 mV vs. SCE. The sensitivity and detection limit were 90.1 microA l/mmol cm(2) and 0.3 micromol/l, respectively.

CONCLUSION

When the sensor was tested in hemolysed erythrocyte samples for GSH determination, a good correlation in results was observed between the sensor and the spectrophotometric method. The sensor showed recovery values between 98% and 102%.

An introduction to thiol redox proteins in the endoplasmic reticulum and a review of current electrochemical methods of detection of thiols

This aim of this paper is to expound the complexity of thiol redox systems in the endoplasmic reticulum of eukaryotic cells to the electroanalytical community. A summary of the state of the art in electrochemical methods for detection of thiols gives an insight into the challenges that need to be addressed to bridge the disparity between current analytical techniques and applications in a 'real' biological scenario.