Prediction of lubrication regimes in wrist implants with spherical bearing surfaces

Comparison of equine articular cartilage thickness in various joints

PURPOSE

Thicknesses of fresh equine articular cartilage surfaces from the fetlock, carpal and stifle joints were measured employing a needle probe test.

MATERIALS AND METHODS

Eighty-seven samples used in measurement were cultivated from fetlock, carpal and stifle joints of 12 deceased within 4 h of death. After approximately three minutes of exposure to air during dissection, all cartilage samples were preserved in a saline solution to keep the articular cartilage hydrated for testing. The thickness was measured on five different spots on the same sample. The thicknesses of the fetlock, carpus and stifle were compared.

RESULTS

The articular cartilage of the stifle was thicker than the fetlock and carpus, while the fetlock and the carpus had similar thickness values. The average thickness of the fetlock, carpal and stifle joint are 0.86, 0.87 and 2.1 mm, respectively. They were statistically compared using the Student t-test. The differences on the articular cartilage thicknesses between the fetlock and stifle, and carpus and stifle were "very highly significant" (p < 0.001). This indicates that the articular cartilage thickness of the stifle is significantly different from that of the fetlock and carpus. Four different surfaces in the fetlock and four in the carpal joint were also compared. Significant differences between each set of the four surfaces were not observed. In the carpus, the difference in thickness between the distal radius and proximal third carpal bone articular cartilage surfaces as well as the proximal radial carpal bone and distal radial carpal bone articular cartilage surfaces were statistically significant.

Lubrication regimes in lumbar total disc arthroplasty

A number of total disc arthroplasty devices have been developed. Some concern has been expressed that wear may be a potential failure mode for these devices, as has been seen with hip arthroplasty. The aim of this paper was to investigate the lubrication regimes that occur in lumbar total disc arthroplasty devices. The disc arthroplasty was modelled as a ball-and-socket joint. Elastohydrodynamic lubrication theory was used to calculate the minimum film thickness of the fluid between the bearing surfaces. The lubrication regime was then determined for different material combinations, size of implant, and trunk velocity. Disc arthroplasties with a metal-polymer or metal-metal material combination operate with a boundary lubrication regime. A ceramic-ceramic material combination has the potential to operate with fluid-film lubrication. Disc arthroplasties with a metal-polymer or metal-metal material combination are likely to generate wear debris. In future, it is worth considering a ceramic-ceramic material combination as this is likely to reduce wear.

Prediction of lubrication regimes in two-piece metacarpophalangeal prostheses

Various designs of two-piece finger prosthesis with conforming spherical surfaces have been proposed. These were compared by calculating the lubrication regime for the material combinations and operating conditions expected at the metacarpophalangeal joints of the fingers. Consideration was given to a range of loads from 2 to 50 N, a range of entraining velocities from 0 to 30 mm/s, and a range of prosthesis radii from 3 to 10 mm. This theoretical lubrication analysis indicated that the optimum material combination of those available for two-piece metacarpophalangeal prostheses is in the order: ceramic-on-ceramic; metal-on-metal; pyrocarbon-on-pyrocarbon; and metal-on-polymer. However, it should be recognised that other factors may take precedence when choosing a material combination for a design of finger prosthesis.

A new design concept for wrist arthroplasty

The wrist joint is frequently affected by arthritis, which leads to pain, loss of function and ultimately deformity. Various designs of wrist arthroplasty have been introduced to attempt to relieve pain and provide a functional range of motion. The first generation of wrist implant was a one-piece silicone elastomer. Later generations have designs that have two parts that articulate against each other. However, wrist implants have not achieved the same clinical success to date, compared with hip and knee implants, and there is a high revision rate associated with them. This paper describes a new design concept for wrist arthroplasty, based around the idea of combining the principles of an articulating implant with that of a flexible elastomer implant. The design consists of assembling a radial, carpal/metacarpal, plate and flexible parts together. The radial and carpal/metacarpal parts are to be made from ultra high molecular weight polyethylene. The bearing surfaces of the radial and carpal/metacarpal parts articulate against the flat surfaces of the plate, made from cobalt chrome molybdenum alloy. The radius on the bearing surface of the radial part enables flexion/extension, while the radius on the carpal/metacarpal surface enables radial/ulnar deviation. The articulation of the carpal/metacarpal part against the plate also allows for rotation as well as flexion/extension. The flexible part, made from Elast-Eon, which is a silicone polyurethane elastomer, is inserted through the hole of the plate and into the holes of the radial and carpal/metacarpal parts.