Methylmercury determination in biological samples by derivatization, solid-phase microextraction and gas chromatography with microwave-induced plasma atomic emission spectrometry

Methylmercury and total mercury content in soft tissues of two bird species wintering in the Baltic Sea near Gdansk, Poland

Of the various forms of Hg occurring in nature, (mono) methylmercury (MeHg) is an especially toxic form and practically all forms of Hg can be converted into MeHg as a result of natural processes. Total mercury (THg) and MeHg were determined in tissues of two piscivorous birds: razorbill Alca torda and black-throated loon Gavia arctica to provide baseline data on current mercury concentrations for liver, kidneys and pectoral muscle mercury concentrations of birds which winter on the south Baltic Sea coast. Intra and inter-specific comparisons were carried out. The study is conducted between winter and autumn and the distributions of mercury in tissues were compared with data in other studies. The following paper contains discussion of the results based on the statistical analysis and ecology aspect. The highest average Hg content was in the liver (loon ≈ 3.86 mg kg^-1 dw; razorbill ≈ 1.57 mg kg^-1 dw), then in the kidneys (loon ≈ 3.14 mg kg^-1 dw; razorbill ≈ 1.53 mg kg^-1 dw) and the lowest concentrations were in pectoral muscles (loon ≈ 1.97 mg kg^-1 dw; razorbill ≈ 0.67 mg kg^-1 dw).

Determination of methylmercury in marine biota samples: method validation

Regulatory authorities are expected to measure concentration of contaminants in foodstuffs, but the simple determination of total amount cannot be sufficient for fully judging its impact on the human health. In particular, the methylation of metals generally increases their toxicity; therefore validated analytical methods producing reliable results for the assessment of methylated species are highly needed. Nowadays, there is no legal limit for methylmercury (MeHg) in food matrices. Hence, no standardized method for the determination of MeHg exists within the international jurisdiction. Contemplating the possibility of a future legislative limit, a method for low level determination of MeHg in marine biota matrixes, based on aqueous-phase ethylation followed by purge and trap and gas chromatography (GC) coupled to pyrolysis-atomic fluorescence spectrometry (Py-AFS) detection, has been developed and validated. Five different extraction procedures, namely acid and alkaline leaching assisted by microwave and conventional oven heating, as well as enzymatic digestion, were evaluated in terms of their efficiency to extract MeHg from Scallop soft tissue IAEA-452 Certified Reference Material. Alkaline extraction with 25% (w/w) KOH in methanol, microwave-assisted extraction (MAE) with 5M HCl and enzymatic digestion with protease XIV yielded the highest extraction recoveries. Standard addition or the introduction of a dilution step were successfully applied to overcome the matrix effects observed when microwave-assisted extraction using 25% (w/w) KOH in methanol or 25% (w/v) aqueous TMAH were used. ISO 17025 and Eurachem guidelines were followed to perform the validation of the methodology. Accordingly, blanks, selectivity, calibration curve, linearity (0.9995), working range (1-800pg), recovery (97%), precision, traceability, limit of detection (0.45pg), limit of quantification (0.85pg) and expanded uncertainty (15.86%, k=2) were assessed with Fish protein Dorm-3 Certified Reference Material. The major contributions to the expanded uncertainty, i.e. 86.1%, arose from the uncertainty associated with recovery, followed by the contribution from fluorescence signal. Additional validation of the methodology developed was effectuated by the comparison with the values reported for MeHg in the IAEA-452 inter-laboratory comparison exercise.

Mercury and methylmercury in Korean herbal medicines and functional health foods

Total mercury (Hg) and methyl mercury (MeHg) were analysed in functional health foods (FHFs) and in Korean herbal medicines (KHMs). A total of 560 samples (FHFs, n = 511; KHMs, n = 49) were collected. The levels of total Hg in 416 samples were lower than the limit of detection. MeHg analysis was conducted in 45 samples and the ranges of MeHg levels in samples were less than the LOD of 38.92 ng g(-1). Weekly intake per body weight (WIPBW) values of total Hg in FHFs and KHMS were 0.89 and 11.77 ng kg(-1) BW, respectively. The margins of exposure (MOEs) of total Hg for FHFs and KHMS were 598,753 and 36,503, respectively. The WIPBW values of MeHg for FHFs and KHMS were 0.22 and 0.01 ng kg(-1) BW, respectively. MOE values of MeHg for FHFs and KHMS were 412,276 and 517,363, respectively.

Simultaneous speciation of monomethylmercury and monoethylmercury by aqueous phenylation and purge-and-trap preconcentration followed by atomic spectrometry detection

A new method for the detection of trace levels of organomercury species has been developed by combining the high enrichment capacity of purge and trap with aqueous phenylation derivatization. Phenylation products of monomethylmercury (MeHg) and monoethylmercury (EtHg) were first separated by capillary gas chromatography and then detected by atomic fluorescence spectrometry (AFS) or inductively coupled plasma mass spectrometry (ICPMS). This combination made it possible to simultaneously quantify trace or ultratrace level of MeHg and EtHg in environmental samples. Method detection limits were 0.03 ng/L for both MeHg and EtHg when AFS was used as the detector and 0.02 and 0.01 ng/L for MeHg and EtHg with ICPMS, respectively. Certified reference materials, IAEA-405 and DORM-2, were analyzed and the results were in accordance with certified values. Both MeHg and EtHg were detected in sediment samples collected from the Florida Everglades and a Canadian wetland. This new method has been validated for the direct detection of trace organomercury species in freshwater samples and has the additional benefits of being free from interference by Cl (-) and dissolved organic matter.

Sensitive determination of free benzophenone-3 in human urine samples based on an ionic liquid as extractant phase in single-drop microextraction prior to liquid chromatography analysis

Benzophenone-3 (BZ3), one of the compounds most commonly used as UV filter in cosmetic products, can be absorbed through the skin into the human body, since it can be found at trace levels in urine from users of cosmetic products that contain BZ3. Moreover, different undesirable effects have been attributed to this compound. Thus, sensitive analytical methods to monitor urinary excretion of this compound should be developed. This paper presents a selective and sensitive methodology for BZ3 determination at ultratrace levels in human urine samples. The methodology is based on a novel microextraction technique, known as single-drop microextraction (SDME). An ionic liquid (IL) has been used as extractant phase instead of an organic solvent. After the microextraction process, the extractant phase was injected into a liquid chromatography system. The variables of interest in the SDME process were optimized using a multivariate optimization approach. A Plackett-Burman design for screening and a circumscribed central composite design for optimizing the significant variables were applied. Ionic strength, extraction time, stirring speed, pH, ionic liquid type, drop volume and sample volume were the variables studied. The optimum experimental conditions found were: sodium chloride concentration, 13% (w/v); extraction time, 25 min; stirring speed, 900 rpm; pH, 2; ionic liquid type, 1-hexyl-3-methylimidazolium hexafluorophosphate ([C(6)MIM][PF(6)]); drop volume, 5 microL; and sample volume, 10 mL. The proposed method requires a standard addition calibration approach, and it has been successfully employed to determine free BZ3 in urine samples coming from human volunteers who applied a sunscreen cosmetic containing this UV filter. The limit of detection was in the order of 1.3 ng mL(-1) and repeatability of the method, expressed as relative standard deviation, was 6% (n=8).

Statistical designs and response surface techniques for the optimization of chromatographic systems

This paper describes fundamentals and applications of multivariate statistical techniques for the optimization of chromatographic systems. The surface response methodologies: central composite design, Doehlert matrix and Box-Behnken design are discussed and applications of these techniques for optimization of sample preparation steps (extractions) and determination of experimental conditions for chromatographic separations are presented. The use of mixture design for optimization of mobile phases is also related. An optimization example involving a real separation process is exhaustively described. A discussion about model validation is presented. Some applications of other multivariate techniques for optimization of chromatographic methods are also summarized.

An ionic liquid as a solvent for headspace single drop microextraction of chlorobenzenes from water samples

A headspace single-drop microextraction (HS-SDME) procedure using room temperature ionic liquid and coupled to high-performance liquid chromatography capable of quantifying trace amounts of chlorobenzenes in environmental water samples is proposed. A Plackett-Burman design for screening was carried out in order to determine the significant experimental conditions affecting the HS-SDME process (namely drop volume, aqueous sample volume, stirring speed, ionic strength, extraction time and temperature), and then a central composite design was used to optimize the significant conditions. The optimum experimental conditions found from this statistical evaluation were: a 5 microL microdrop of 1-butyl-3-methylimidazolium hexafluorophosphate, exposed for 37 min to the headspace of a 10 mL aqueous sample placed in a 15 mL vial, stirred at 1580 rpm at room temperature and containing 30% (w/v) NaCl. The calculated calibration curves gave a high level of linearity for all target analytes with correlation coefficients ranging between 0.9981 and 0.9997. The repeatability of the proposed method, expressed as relative standard deviation, varied between 1.6 and 5.1% (n=5). The limits of detection ranged between 0.102 and 0.203 microg L(-1). Matrix effects upon extraction were evaluated by analysing spiked tap and river water as well as effluent water samples originating from a municipal wastewater treatment plant.

Total mercury and mercury species in birds and fish in an aquatic ecosystem in the Czech Republic

Total mercury and mercury species (methylmercury-MeHg, inorganic mercury--Hg(2+)) were determined in the aquatic ecosystem Záhlinice (Czech Republic). Four tissues (muscle, intestines, liver and kidney) of three bird species--cormorant, great crested grebe and Eurasian buzzard, muscle tissues of common carp, grass carp, northern pike, goldfish, common tench, perch and rudd, aquatic plants (reed mace and common reed), sediments and water were analysed. Relative contents of MeHg (of total Hg) were in the range from 71% to 94% and from 15% up to 62% in the muscle and intestines and in liver, respectively, for all birds. Statistically significant differences were found between contents of MeHg in liver tissues of young and adult cormorant populations (F(4.60)=56.71, P<10(-5)). Relative contents of MeHg in muscle tissues of fishes were in the range from 65.1% to 87.9% of total Hg.

UV Irradiation Controlled Cold Vapor Generation Using SnCl2 as Reductant for Mercury Speciation

A simple and ultrasensitive method, which was based on cold vapor generation (CVG) coupled to atomic fluorescence spectrometry (AFS), was proposed for speciation analysis of inorganic mercury (Hg2+) and methylmercury (MeHg) in water samples. In the presence of UV irradiation, all the mercury (MeHg+Hg2+) in a sample solution can be reduced to Hg0 by SnCl2; without UV irradiation, only Hg2+ species can be determined. So the concentration of MeHg can be obtained from the difference of the total mercury and Hg2+ concentration; thus, speciation analysis of Hg2+ and MeHg was simply achieved without chromatographic separation. Under the optimized experimental conditions, the limits of detection were 0.01 ng mL-1 for both Hg2+ and MeHg. The sensitivity and limit of detection were not dependent on the mercury species, and a simple Hg2+ aqueous standard series can be used for the determination of both Hg2+ and MeHg.

Behaviour of carbamate pesticides in gas chromatography and their determination with solid-phase extraction and solid-phase microextraction as preconcentration steps

This work reports a study of the chromatographic behaviour of seven carbamate pesticides (aldicarb, carbetamide, propoxur, carbofuran, carbaryl, methiocarb, and pirimicarb) by gas chromatography-mass spectrometry (GC-MS). Variables such as injector temperature, solvent, injection mode, and the degree of ageing of the chromatographic column were studied. One of the aims of this work was to achieve a controlled decomposition of carbamates by a solid-phase microextraction (SPME) preconcentration step with a polyacrylate fibre in order to obtain reproducible chromatographic signals of the degradation products. Optimisation of the SPME process was accomplished by means of experimental design. Several methods using ultrapure water were developed with different preconcentration configurations: SPME-GC-MS, SPE followed by SPME-GC-MS, and SPE plus GC-MS. For all the pesticides studied, method detection limit (MDL) values below 0.1 microg L-1 were reached in at least one of the proposed configurations.

Investigation of the species-specific degradation behaviour of methylmercury and ethylmercury under microwave irradiation

The degradation behaviour of methylmercury (MeHg) under microwave irradiation is investigated, as is the (different) degradation behaviour of ethylmercury (EtHg) under similar irradiation. A simple and highly sensitive SPME-GC-pyrolysis-AFS system was used to analyse the aqueous MeHg and EtHg standard solutions after derivatization with sodium tetraphenylborate (NaBPh(4)). Samples were irradiated in a microwave digester at microwave powers ranging from 20 to 160 W for durations of 2 to 10 min. The different tolerances towards microwave treatment of the two organomercury species were evident. Practically no degradation was experienced for MeHg for up to 8 minutes of irradiation at 120 W or for up to 4 minutes at 160 W. Significant analyte loss was observed for EtHg after 2 minutes at 40 W of microwave power.

SPME-GC-pyrolysis-AFS determination of methylmercury in marine fish products by alkaline sample preparation and aqueous phase phenylation derivatization

Characterization of a cost-efficient analytical method based on alkaline sample digestion with KOH and NaOH, followed by aqueous phase phenylation derivatization with NaBPh4 and solid phase microextraction (SPME) for the determination of methylmercury in typical fish-containing food samples commercially available in Hungary, is reported. The sample preparation procedure along with the applied SPME-GC-pyrolysis-AFS system was validated by measuring certified reference materials (CRM) BCR-464, TORT-2, and a candidate CRM BCR 710. To carry out an estimation of average Hungarian methylmercury exposures via marine fish and/or fish-containing food consumption, 16 commercially available products and 3 pooled representative seafood samples of-according to a previous European survey--the three most consumed fish species in Hungary, herring, sardines, and hake, were analyzed. Methylmercury concentrations of the analyzed samples were in the range 0.016-0.137 microg of MeHg g(-1) dry weight as Hg.

Rapid determination of tramadol in human plasma by headspace solid-phase microextraction and capillary gas chromatography-mass spectrometry

A simple, rapid and sensitive method for determination of tramadol in plasma samples was developed using headspace solid-phase microextraction (HS-SPME) and gas chromatography with mass spectrometry (GC-MS). The optimum conditions for the SPME procedure were: headspace extraction on a 65-microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber; 0.5 mL of plasma modified with 0.5 mL of sodium hydroxide (0.1 M); extraction temperature of 100 degrees C, with stirring at 2000 rpm for 30 min. The calibration curve showed linearity in the range of 1-400 ng mL(-1) with regression coefficient corresponding to 0.9986 and coefficient of the variation of the points of the calibration curve lower than 10%. The detection limit for tramadol in plasma was 0.2 ng mL(-1). The proposed method was successfully applied to determination of tramadol in human plasma samples from 10 healthy volunteers after a single oral administration.

Solid-phase extraction–gas chromatography–mass spectrometry using a fullerene sorbent for the determination of inorganic mercury(II), methylmercury(I) and ethylmercury(I) in surface waters at sub-ng/ml levels

A novel, straightforward solid-phase extraction system for the determination of inorganic mercury and organomercury compounds in water is proposed. The analytes, in a buffer medium at pH 4.5, are sorbed as diethyldithiocarbamate complexes on a C60 fullerene column an subsequently eluted and derivatized with sodium tetra-n-propylborate in ethyl acetate. Following elution, 1 microl of extract is injected into a gas chromatograph-mass spectrometer system. The proposed gas chromatography-mass spectrometry speciation method exhibits a linear range of 4-1 ng/ml, and a detection limit of 1.5 ng/l (sample volume, 50 ml). Its repeatibility, as relative standard deviation (RSD) (from 11 standards containing 50 ng/l for each analyte), is ca. 7%. No interferences from metals ions, such as Zn2+, Fe3+, Sb3+, As3+, Pb2+, Ni2+, Cu2+, Sn2+, Co2+, Mn2+ and Cd2+ were encountered at concentrations 1000 times higher than those of the mercury compounds. The method was used for the speciation of inorganic mercury, methylmercury and ethylmercury in various types of water including sea and waste water.

Speciation analysis of mercury by solid-phase microextraction and multicapillary gas chromatography hyphenated to inductively coupled plasma–time-of-flight-mass spectrometry

This paper reports the development of an analytical approach for speciation analysis of mercury at ultra-trace levels on the basis of solid-phase microextraction and multicapillary gas chromatography hyphenated to inductively coupled plasma-time-of-flight mass spectrometry. Headspace solid-phase microextraction with a carboxen/polydimethylsyloxane fiber is used for extraction/preconcentration of mercury species after derivatization with sodium tetraethylborate and subsequent volatilization. Isothermal separation of methylmercury (MeHg), inorganic mercury (Hg2+) and propylmercury (PrHg) used as internal standard is achieved within a chromatographic run below 45 s without the introduction of spectral skew. Method detection limits (3 x standard deviation criteria) calculated for 10 successive injections of the analytical reagent blank are 0.027 pg g(-1) (as metal) for MeHg and 0.27 pg g(-1) for Hg2+. The repeatability (R.S.D., %) is 3.3% for MeHg and 3.8% for Hg2+ for 10 successive injections of a standard mixture of 10pg. The method accuracy for MeHg and total mercury is validated through the analysis of marine and estuarine sediment reference materials. A comparison of the sediment data with those obtained by a purge-and-trap injection (PTI) method is also addressed. The analytical procedure is illustrated with some results for the ultra-trace level analysis of ice from Antarctica for which the accuracy is assessed by spike recovery experiments.

Application of isotope dilution to the determination of methylmercury in fish tissue by solid-phase microextraction gas chromatography–mass spectrometry

Species-specific isotope dilution (ID) calibration using solid-phase microextraction (SPME) in combination with gas chromatography-mass spectrometry (GC-MS) for separation and detection of methylmercury (MeHg) in fish tissue is described. Samples were digested with methanolic potassium hydroxide. Analytes were propylated and headspace sampled with a polydimethylsiloxane-coated SPME fused-silica fiber. ID analysis was performed using a laboratory-synthesized 198Hg-enriched methylmercury (Me 198Hg) spike. Using selective ion monitoring (SIM) mode, the intensities of Me 202HgPr+ at m/z 260 and Me 198HgPr+ at m/z 256 were used to calculate the m/z ratio at 260/256, which was used to quantify MeHg in NRCC CRM DORM-2 fish tissue. A MeHg concentration of 4.336 +/- 0.091 microg g(-1) (one standard deviation, n = 4) as Hg was obtained in DORM-2, in good agreement with the certified value of 4.47 +/- 0.32 microg g(-1) (95% confidence interval). A concentration of 4.58 +/- 0.31 microg g(-1) was determined by standard additions calibration using ethylmercury (EtHg) as an internal standard. The three-fold improvement in the precision of measured MeHg concentrations using ID highlights its superiority in providing more precise results compared to the method of standard additions. A method detection limit (3 S.D.) of 0.037 microg g(-1) was estimated based on a 0.25 g subsample of DORM-2.