Extraction and precipitation particle coating using supercritical CO2

Preparation and Characterization of Fenofibrate Microparticles with Surface-Active Additives: Application of a Supercritical Fluid-Assisted Spray-Drying Process

In this study, supercritical fluid-assisted spray-drying (SA-SD) was applied to achieve the micronization of fenofibrate particles possessing surface-active additives, such as d-α-tocopheryl polyethylene glycol 1000 succinate (TPGS), sucrose mono palmitate (Sucroester 15), and polyoxyethylene 52 stearate (Myrj 52), to improve the pharmacokinetic and pharmacodynamic properties of fenofibrate. For comparison, the same formulation was prepared using a spray-drying (SD) process, and then both methods were compared. The SA-SD process resulted in a significantly smaller mean particle size (approximately 2 μm) compared to that of unprocessed fenofibrate (approximately 20 μm) and SD-processed particles (approximately 40 μm). There was no significant difference in the effect on the particle size reduction among the selected surface-active additives. The microcomposite particles prepared with surface-active additives using SA-SD exhibited remarkable enhancement in their dissolution rate due to the synergistic effect of comparably moderate wettability improvement and significant particle size reduction. In contrast, the SD samples with the surface-active additives exhibited a decrease in dissolution rate compared to that of the unprocessed fenofibrate due to the absence of particle size reduction, although wettability was greatly improved. The results of zeta potential and XPS analyses indicated that the surface-active additive coverage on the surface layer of the SD-processed particles with a better wettability was higher than that of the SA-SD-processed composite particles. Additionally, after rapid depletion of hydrophilic additives that were excessively distributed on the surfaces of SD-processed particles, the creation of a surface layer rich in poorly water-soluble fenofibrate resulted in a decrease in the dissolution rate. In contrast, the surface-active molecules were dispersed homogeneously throughout the particle matrix in the SA-SD-processed microparticles. Furthermore, improved pharmacokinetic and pharmacodynamic characteristics were observed for the SA-SD-processed fenofibrate microparticles compared to those for the SD-processed fenofibrate particles. Therefore, the SA-SD process incorporating surface-active additives can efficiently micronize poorly water-soluble drugs and optimize their physicochemical and biopharmaceutical characteristics.

Biodegradable particle formation for drug and gene delivery using supercritical fluid and dense gas

Recent developments in biodegradable particle formation using supercritical fluids and dense gases have been reviewed with an emphasis on studies of micronizing and encapsulating poorly-soluble pharmaceuticals and gene. General review articles published in previous years have then been provided. A brief description of the operating principles of some types of particle formation processes is given. These include the rapid expansion of supercritical solutions (RESS), the particles from gas-saturated solution (PGSS) processes, the gas antisolvent process (GAS), and the supercritical antisolvent process (SAS). The papers have been reviewed under two groups, one involving the production of particles from pure biodegradable substances, and the other involving coating, capsule, and impregnation that contain active components, especially those that relate to pharmaceuticals. This review is a comprehensive review specifically focused on the formation of biodegradable particles for drug and gene delivery system using supercritical fluid and dense gas.

Comparative Physicochemical Characterization of Phospholipids Complex of Puerarin Formulated by Conventional and Supercritical Methods

PURPOSE

The aim of this work was to compare the physicochemical characteristics of the phospholipids complex of puerarin (Pur) prepared by traditional methods (solvent evaporation, freeze-drying and micronization) and a supercritical fluid (SCF) technology. The physicochemical properties of the pure drug and the corresponding products prepared by two different SCF methods were also compared.

METHODS

Solid-state characterization of particles included differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD), solubility, dissolution rate and scanning electron microscopy (SEM) examinations. Besides puerarin phospholipids complex (PPC) by four different methods, the solid-state properties of unprocessed, gas antisolvent (GAS) crystallized and solution enhanced dispersion by supercritical fluid (SEDS) precipitated puerarin samples were also compared. Crystallinity was assessed using DSC and XRPD. Drug-phospholipids interactions were characterized using Fourier transform infrared spectroscopy (FTIR). SEM was used to determine any morphological changes. Pharmaceutical performance was assessed in dissolution rate and solubility tests.

RESULT

The results of the physical characterization attested a substantial correspondence of the solid state of the drug before and after treatment with GAS technique, whereas a pronounced change in size and morphology of the drug crystals was noticed. The GAS-processed puerarin exhibited a better crystal shape confirmed by DSC, XRPD and IR. Polymorphic change of puerarin during SEDS coupled with the dramatic reduction of the dimensions determined a remarkable enhancement of its solubility and in vitro dissolution rate. Phospholipids complex prepared using supercritical fluid technology showed similar properties of physical state, thermal stability and molecular interaction with phospholipids (PC) to those of corresponding systems prepared by other three conventional methods namely solvent evaporation, freeze-drying and micronization as proved by XRPD, DSC, and FTIR. The best dissolution rate was obtained by SEDS-prepared complex, while the highest solubility was obtained for solvent evaporation method.

CONCLUSION

Supercritical fluid technology for the preparation of puerarin and its phospholipids complex has been proven to have significant advantages over the solvent evaporation technique and other conventional methods.

Solventless pharmaceutical coating processes: a review

Coatings are an essential part in the formulation of pharmaceutical dosage form to achieve superior aesthetic quality (e.g., color, texture, mouth feel, and taste masking), physical and chemical protection for the drugs in the dosage forms, and modification of drug release characteristics. Most film coatings are applied as aqueous- or organic-based polymer solutions. Both organic and aqueous film coating bring their own disadvantages. Solventless coating technologies can overcome many of the disadvantages associated with the use of solvents (e.g., solvent exposure, solvent disposal, and residual solvent in product) in pharmaceutical coating. Solventless processing reduces the overall cost by eliminating the tedious and expensive processes of solvent disposal/treatment. In addition, it can significantly reduce the processing time because there is no drying/evaporation step. These environment-friendly processes are performed without any heat in most cases (except hot-melt coating) and thus can provide an alternative technology to coat temperature-sensitive drugs. This review discusses and compares six solventless coating methods - compression coating, hot-melt coating, supercritical fluid spray coating, electrostatic coating, dry powder coating, and photocurable coating - that can be used to coat the pharmaceutical dosage forms.