The electrical resistance of enamel-dentine cylinders. Influence of NaCl content in storage solutions

Accuracy of an electrical impedance device in estimation of remaining dentin thickness vs cone beam computed tomography

The objective of this study is to compare the estimated values of remaining dentin thickness (RDT) recorded by a newly introduced electrical impedance device (Prepometer) with cone beam computed tomography (CBCT) and histological in situ measurement. A total number of thirty human molars were used in this study. A deep class I cavity was prepared. The RDT for each cavity was measured with Prepometer in three different points (mesial, middle, and distal). Same specimens were imaged with high-resolution Cone Beam Computed Tomography CBCT (0.1 mm voxel size) using I CAT next Generation Machine (Imaging Science International, Hatfield, PA, USA), to provide the highest possible accuracy of linear measurements. Finally, the specimens were vertically sectioned parallel to the long axis of the tooth in a mesiodistal direction splitting the cavity into two halves through its center. Then, the actual RDT of each half will be measured in the same three points using a digital caliper. The outcome of one-way ANOVA revealed that there was no significant difference in RDT values measured by prepometer device, CBCT, or histological sectioning methods (p > 0.05). Within the limitations of this laboratory study, prepometer seems to be a potential non-invasive accurate measuring tool for RDT. Based on the findings of this study, the Prepometer can be considered as an easily handled and less-expensive method compared to CBCT to evaluate the RDT. Also, it can be used in dental schools and with less-experienced operators to avoid traumatic exposures of the dental pulp.

Sweet Drinks as Fuels for an Alkaline Fuel Cell with Nonprecious Catalysts

Sugar has the potential to create enough energy to power mobile electronics. Various sugar-powered fuel cells have been reported, however, most of them used pure glucose as substrate and enzymes/noble metals as catalysts. In this work, an alkaline fuel cell with cheap catalysts were constructed, and different sweet drinks were used as fuels for power generation. The influence of different substrates on the electrochemical performance was characterized under the controlled conditions. Our experimental results showed that the fuel cell fueled with carbonated soft drinks had the best performance under the conditions of 99.95 g/L chemical oxygen demand and 3M KOH. The power densities of the fuel cell fueled with different substrates decreased in the order of Pepsi (33.41 W/m2) > Sprite (28.38 W/m2) > apple juice (20.63 W/m2) > Coca (16.31 W/m2) > pear juice (15.31 W/m2) > orange juice (12.75 W/m2), which was consistent with linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS) analysis. This is the first report on alkaline fuel cell (AFC) performance using different sweet drinks as substrate. These values are more than 10 times higher than those of reported microbial fuel cells. Our findings demonstrated that sweet drinks fueled alkaline fuel cells can be a promising energy source for low-power electronics.

Influence of sodium chloride content in electrolyte solution on electrochemical impedance measurements of human dentin

Background:

The aim of this study was to investigate the influence of sodium chloride (NaCl) content in electrolyte solution on electrochemical impedance measurements of human dentin by employing electrochemical impedance spectroscopy.

Materials and Methods:

Dentin samples were prepared from extracted molars. Electrochemical impedance measurements were carried out over a wide frequency range (0.01Hz-10MHz). After measurements, samples were characterized using scanning electron microscopy.

Results:

Electrochemical impedance measurements showed that the mean values of dentin electrical resistance were 4284, 2062, 1336, 53 and 48kΩ at different NaCl contents in electrolyte solution. One-way ANOVA test of mean values of dentin electrical resistance revealed a significant difference (P < 0.0001) as a function of NaCl content in electrolyte solution. Comparing electrical resistance values of dentin samples at 0.05% w/v and 0.9% w/v concentrations were found to be significantly different (P < 0.05 at 95% confidence level). Scanning electron microscopy revealed structure of dentin sample with intertubular dentin matrix and distribution of patent dentinal tubules.

Conclusion:

This in vitro study indicated, through electrochemical impedance spectroscopy measurements, that electrical resistance of dentin was affected by the concentration of NaCl in electrolyte solution. It is clear from the current study that NaCl concentration in electrolyte solution has a marked influence on dentin electrical resistance. Therefore, this baseline data need to be considered in any future study on dental samples.

Age-related changes in ac-impedance spectroscopy studies of normal human dentine

Non-destructive methods, such as the ac-impedance technique, have recently been applied to early caries detection and to identify micro-leakage between tooth structure and filling materials. However, in vitro impedance measurements are affected by a number of external factors. The purpose of present study was to investigate the effect of the age of teeth on impedance measurements of human dentine by employing electrical impedance spectroscopy (EIS). Fully hydrated dentine samples were prepared from extracted third molars of 20 and 50 year old patients. Ac-impedance measurements were carried out over a wide frequency range. Impedance measurements showed that there were differences in impedance between young and older dentine. In their circuit models, both resistance and capacitance were found to be significantly different (p < 0.05) for the two age groups. One of the age-related changes in dentine is the formation of peritubular dentine on the inner walls of dentinal tubules and we propose that this is responsible for the differences in impedance. Sample or patient age therefore must be considered when making impedance measurements on any tooth.