The effects of various load paths and different loads on the load transfer characteristics of the wrist

The influence of partial union on the mechanical strength of scaphoid fractures: a finite element study

Assessment of scaphoid fracture union on computed tomography scans is not currently standardized. We investigated the extent of scaphoid waist fracture union required to withstand physiological loads in a finite element model, based on a high-resolution CT scan of a cadaveric forearm. For simulations, the scaphoid waist was partially fused at the radial and ulnar sides. A physiological load of 100 N was transmitted to the scaphoid and the minimal amount of union to maintain biomechanical stability was recorded. The orientation of the fracture plane was varied to analyse the effect on biomechanical stability. The results indicate that the scaphoid is more prone to re-fracture when healing occurs on the ulnar side, where at least 60% union is required. Union occurring from the radial side can withstand loads with as little as 25% union. In fractures more parallel to the radial axis, the scaphoid seems less resistant on the radial side, as at least 50% union is required. A quantitative CT scan analysis with the proposed cut-off values and a consistently applied clinical examination will guide the clinician as to whether mid-waist scaphoid fractures can be considered as truly united.

Volar versus combined dorsal and volar plate fixation of complex intraarticular distal radius fractures with small dorsoulnar fragment - a biomechanical study

Complex intraarticular distal radius fractures (DRFs), commonly managed with volar locking plates, are challenging. Combined volar and dorsal plating is frequently applied for treatment, however, biomechanical investigations are scant. The aim of this biomechanical study was to investigate volar plating versus double plating in DRFs with different degrees of lunate facet comminution.Thirty artificial radii with simulated AO/OTA 23-C2.1 and C3.1 DRFs, including dorsal defect and lunate facet comminution, were assigned to 3 groups: Group 1 with two equally-sized lunate facet fragments; Group 2 with small dorsal and large volar fragment; Group 3 with three equally-sized fragments. The specimens underwent volar and double locked plating and non-destructive ramped loading in 0° neutral position, 40° flexion and 40° extension.In each tested position, stiffness: (1) did not significantly differ among groups with same fixation method (p ≥ 0.15); (2) increased significantly after supplemental dorsal plating in Group 2 and Group 3 (p ≤ 0.02).Interfragmentary displacements between styloid process and lunate facet in neutral position were below 0.5 mm, being not significantly different among groups and plating techniques (p ≥ 0.63).Following volar plating, angular displacement of the lunate facet to radius shaft was significantly lower in Group 1 versus both Group 2 and Group 3 (p < 0.01). It decreased significantly after supplemental dorsal plating in Group 2 and Group 3 (p < 0.01), but not in Group 1 (p ≥ 0.13), and did not differ significantly among the three groups after double plating (p ≥ 0.74).Comminution of the lunate facet within its dorsal third significantly affected the biomechanical outcomes related to complex intraarticular DRFs treated with volar and double locked plates.Double plating demonstrates superior stability versus volar plating only for lunate facet comminution within its dorsal third. In contrast, volar plating could achieve stability comparable with double plating when the dorsal third of the lunate facet is not separated by the fracture pattern. Both fixation methods indicated achievable absolute stability between the articular fragments.

Wrist movements induce torque and lever force in the scaphoid: an ex vivo study

Purpose

We hypothesised that intercarpal K-wire fixation of adjacent carpal bones would reduce torque and lever force within a fractured scaphoid bone.

Methods

In eight cadaver wrists, a scaphoid osteotomy was stabilised using a locking nail, which also functioned as a sensor to measure isometric torque and lever forces between the fragments. The wrist was moved through 80% of full range of motion (ROM) to generate torque and force within the scaphoid. Testing was performed with and without loading of the wrist and K-wire stabilisation of the adjacent carpal bones.

Results

Average torque and lever force values were 49.6 ± 25.1 Nmm and 3.5 ± 0.9 N during extension and 41 ± 26.7 Nmm and 8.1 ± 2.8 N during flexion. Torque and lever force did not depend on scaphoid size, individual wrist ROM, or deviations of the sensor versus the anatomic axis. K-wire fixation did not produce significant changes in average torque and lever force values except with wrist radial abduction (P = 0.0485). Other than wrist extension, torque direction was not predictable.

Conclusion

In unstable scaphoid fractures, we suggest securing rotational stability with selected implants for functional postoperative care. Wrist ROM within 20% extension and radial abduction to 50% flexion limit torque and lever force exacerbation between scaphoid fragments.

First-stage scapholunate fusion for the treatment of a chronic lunate dislocation: A case report

RATIONALE

Lunate dislocation is a rare injury to the wrist caused by high-energy trauma, and poor prognosis is often associated with missed initial diagnosis. To date, there is no consensus regarding an effective treatment plan for such cases.

PATIENT CONCERNS

Here, we describe the case of a 36-year-old man who presented with lunate dislocation following a delay in diagnosis of over 7 weeks, and further illuminate its diagnosis and treatment.

DIAGNOSIS

The diagnosis of chronic lunate dislocation was rendered.

INTERVENTIONS

The patient was treated using reduction via the dorsal approach brachial plexus anesthesia. After the reduction, a headless compression screw fixation was performed for first-stage scapholunate fusion, and Kirschner wire fixation of the lunate-triquetrum-hamate was used to stabilize the distal and proximal carpal rows.

OUTCOMES

The patient was followed up for 1 year and showed wrist function recovered well; radiographic examination showed no lunate dislocation and successful scapholunate bony fusion. A satisfactory outcome was achieved.

LESSONS

The case study presented here provide evidence that performing an effective first-stage scapholunate fusion is recommended to achieve better therapeutic outcomes for a chronic lunate dislocation. Furthermore, this approach led to a good long-term clinical outcome in our case.

The biomechanical and functional relationships of the proximal radioulnar joint, distal radioulnar joint, and interosseous ligament

This biomechanical study assessed integrated function of the proximal radioulnar joint (PRUJ), interosseous ligament (IOL), and distal radioulnar joint (DRUJ). Tekscan™ pressure sensors were inserted into the DRUJ and PRUJ of 15 cadaveric specimens. MicroStrain(®) sensors were mounted onto the IOL on nine of these specimens. A customized biomechanical jig was used to apply axial loads and take measurements through pronosupination. The PRUJ, IOL, and DRUJ were shown to function as an integrated osseoligamentous system distributing applied load. The PRUJ has transmitted pressure profiles similar to those of the DRUJ. Different IOL components support loading at different stages of pronosupination. The IOL is lax during pronation. Mid-IOL tension peaks in the midrange of forearm rotation; distal-IOL tension peaks in supination. Axial loading consistently increases IOL strain in a non-linear fashion. There are clinical implications of this work: disease or surgical modification of any of these structures may compromise normal biomechanics and function.

Retrograde percutaneous screw fixation for scaphoid type II non-union in Schernberg zones 2 to 4: a series of 38 cases

Regardless of the treatment used, 25 to 45% of scaphoid fractures do not heal. Open surgery compromises vascularization and destabilizes ligament attachments. The aim of this retrospective study was to assess the value of retrograde percutaneous screw fixation of Alnot stage IIA and IIB scaphoid non-union in Schernberg zones 2 to 4. This series included 38 patients with a mean age of 31 years. Based on the Alnot classification, there were 16 stage IIA non-unions (12 in zone 3 and 4 in zone 2 according to the Schernberg classification) and 22 stage IIB non-unions (9 in zone 3 and 13 in zone 2). The time elapsed between the initial trauma and the surgical treatment was 10 months on average. Percutaneous retrograde fixation was performed with a cannulated 2.7mm compression screw. At 25 months follow-up, 31 of the non-union cases had healed (81.6%), of which 14 were stage IIA (87.5%) and 17 were stage IIB (77.3%), after an average 6.3 months. Average pain was 1.6. The average Quick DASH was 17.3/100. Compared to the opposite side, the average range of motion was 84.8% in flexion, 84.7% in extension, 98.9% in pronation, 96.5% in supination, 96.8% in ulnar deviation and 86.4% in radial deviation. The grip strength was 80.4% of the contralateral side. Seven patients did not heal after screw fixation; four of them healed after additional electromagnetic stimulation and three after addition of a vascularized bone graft. Based on this study's results, stage IIA non-unions can heal with simple retrograde percutaneous screw fixation. The same procedure could be enough for stage IIB non-union cases, however we recommend adding a cancellous bone graft by arthroscopy. Open surgery procedures are preferred when percutaneous procedures have failed.

Trabecular bone structure in the primate wrist

Trabecular (or cancellous) bone has been shown to respond to mechanical loading throughout ontogeny and thus can provide unique insight into skeletal function and locomotion in comparative studies of living and fossil mammalian morphology. Trabecular bone of the hand may be particularly functionally informative because the hand has more direct contact with the substrate compared with the remainder of the forelimb during locomotion in quadrupedal mammals. This study investigates the trabecular structure within the wrist across a sample of haplorhine primates that vary in locomotor behaviour (and thus hand use) and body size. High-resolution microtomographic scans were collected of the lunate, scaphoid, and capitate in 41 individuals and eight genera (Homo, Gorilla, Pan, Papio, Pongo, Symphalangus, Hylobates, and Ateles). We predicted that particular trabecular parameters would 1) vary across suspensory, quadrupedal, and bipedal primates based on differences in hand use and load, and 2) scale with carpal size following similar allometric patterns found previously in other skeletal elements across a larger sample of mammals and primates. Analyses of variance (trabecular parameters analysed separately) and principal component analyses (trabecular parameters analysed together) revealed no clear functional signal in the trabecular structure of any of the three wrist bones. Instead, there was a large degree of variation within suspensory and quadrupedal locomotor groups, as well as high intrageneric variation within some taxa, particularly Pongo and Gorilla. However, as predicted, Homo sapiens, which rarely use their hands for locomotion and weight support, were unique in showing lower relative bone volume (BV/TV) compared with all other taxa. Furthermore, parameters used to quantify trabecular structure within the wrist scale with size generally following similar allometric patterns found in trabeculae of other mammalian skeletal elements. We discuss the challenges associated with quantifying and interpreting trabecular bone within the wrist.

In vivo changes in contact regions of the radiocarpal joint during wrist hyperextension

PURPOSE

Distal radius and scaphoid fractures commonly occur after a fall with the hand outstretched and wrist hyperextended. We investigated contact characteristics of the radiocarpal joint in neutral position, hyperextension, and hyperextension combined with radial deviation in vivo.

METHODS

Eight volunteers without a known history of wrist injury were enrolled. We obtained computed tomography scans with 3-dimensional reconstructions of the subjects' right wrists in neutral, hyperextension, and hyperextension with 10° of radial deviation. The contact regions of the radiocarpal joint were mapped. The direction and distance of changes in the contact region centers were recorded and analyzed.

RESULTS

From neutral position to hyperextension, the contact of the scaphoid substantially shifted from the middle to the dorsal part of the articular surface of the radius in 5 of the 8 wrists. With these wrists further deviated radially, the contact shifted to the surface over the radial styloid. In the other wrists, the contact of the scaphoid remained in the center of the radial articular surface. In all wrists, the contact of the radius on the scaphoid shifted from the proximal lateral surface of the scaphoid to the proximal dorsal surface of the scaphoid, and the contact of the radius on the lunate shifted dorsally.

CONCLUSIONS

During wrist hyperextension, the contact of the scaphoid on the distal radius exhibited 2 possible types of changes: either shifting from the mid-portion to the dorsal ridge of the articular surface of the radius or remaining at the center of the articular surface. Combined wrist hyperextension with radial deviation caused the scaphoid to contact the radius over the radial styloid. The contact of the radius on the scaphoid shifted from proximal lateral to proximal dorsal scaphoid, and that on the lunate shifted dorsally.

CLINICAL RELEVANCE

This study provided in vivo mechanical findings to improve our understanding of the mechanism of hyperextension injuries of carpus.

Patterns of radiocarpal joint articular cartilage wear in cadavers

The radiocarpal joint transmits about 80% of the compression forces crossing the wrist. However, primary osteoarthritis of this joint is surprisingly uncommon, suggesting that articular cartilage wear is not sufficient to produce arthritic symptoms. By examining the distal radius, scaphoid, and lunate in aged cadavers, wear patterns were charted and measured, allowing assessment of radiocarpal joint wear and mechanics. Bilateral radiocarpal joints of 16 females and 14 males (age 77.7 ± 14.4, N = 30) were exposed and measurements of the wear recorded microscopically. Wear locations were mapped, and X-Y loci and wear areas calculated. Gender right and sides compared. Over 95% of distal radius wear showed distinct radial-scaphoid and radial-lunate wear areas. These bilateral areas were in the palmar half of the distal radius. One main central wear area was seen in 95% of the scaphoid, and 97% of the lunate articular surfaces that were examined. Articular wear showed a circular pattern and was minimal in 95.7% of the surfaces, and the lunate showed the largest wear area. Wear patterns in males and females support the literature that for most ADLs the wrist is in slight extension and ulnar deviation. There are gender differences, but wear areas between sides were similar. Female wear indicates their wrist is positioned more often in a more extended and ulnarly deviated position than males. The wear patterns suggest rotational movements of the scaphoid and lunate during wrist motion and that the wrist is most often used in neutral flexion/extension to slight extension.

The effect of distal radius locking plates on articular contact pressures

PURPOSE

Fractures of the distal radius are among the most common injuries treated in hand surgery practice, and distal radius locking plates have become an increasingly popular method of fixation. Despite widespread use of this technology, it is unknown whether the subchondral placement of locking screws affects the loading profile of the distal radius. Our study was designed to determine whether subchondral locking screws change the articular contact pressures in the distal radius.

METHODS

Twelve cadaveric forearms underwent a previously described axial loading protocol in a materials testing machine. We used an intra-articular, real-time computerized force sensor to measure peak contact pressure, total pressure, and contact area in the distal radius. Internal validation of sensor placement and reproducibility was conducted. Each specimen was tested before fixation (control), after application of a palmar distal radius locking plate, and after simulation of a metaphyseal fracture.

RESULTS

We identified no statistically significant differences in maximum pressure, total pressure, and contact area among control, plated, and plated and fractured specimens. However, the contact footprint-represented by squared differences in force across the sensor-were significantly different between the control group and both plated groups.

CONCLUSIONS

The technique for measuring contact pressures produces highly repeatable values. Distal radius locking plates with subchondral hardware placement do not seem to significantly change articular contact pressures.

Variations of capitate morphology in the wrist

PURPOSE

This anatomical study details and categorizes variations in capitate morphology and associated structures in the human cadaveric wrist.

METHODS

We dissected 107 cadaveric wrists. Capitate morphology, the presence of capitate and hamate ridges, the lunate types, and the width of the medial hamate facet of type II lunates and 4th carpometacarpal joint types were recorded.

RESULTS

Three types of capitate were identified. The flat type (69/107, or 65%) was characterized by a horizontally oriented (radio-ulnar) lunate-capitate articulation and a longitudinally oriented (proximal-distal) scaphoid-capitate articulation. The flat type was associated with type I lunates or type II lunates with a smaller facet. The spherical type (23/107, or 22%) was associated with a concave articulation formed by the scaphoid and lunate articulations, with an indistinct border between the scaphoid and lunate facets. The width of the medial hamate facet of type II lunates in wrists with a spherical-type capitate was <or=4 mm. The V-shaped type (15/107, or 14%) was characterized by separate lunate and scaphoid facets that converge, forming a V-shape. All the V-shaped capitates had a type II lunate with a large facet.

CONCLUSIONS

A relationship was found between the 3 capitate types and both the lunate types and the width of the medial hamate facet of the type II lunates. Further study is warranted to determine if these differences in capitate morphology influence the development or progression of various wrist pathologic conditions, such as Kienböck's disease and post-traumatic arthritis associated with scapholunate dissociation and scaphoid nonunion, and the outcome of certain surgical procedures, such as a proximal row carpectomy.

Load transmission through the wrist in the extended position

PURPOSE

The wrist is subjected to extremely high compressive loads in the extended position, but pathoanatomy of this region remains unclear. The purpose of this study was to analyze force transmission in the maximum extended position to clarify the pathomechanics of wrist injury.

METHODS

Two sets of computed tomography images of wrist joints were obtained for 7 normal subjects: one set in neutral position and the other set in maximum extension. A three-dimensional rigid body spring model was used to analyze stress distributions through the wrist joint. The wrist joint was constructed from computed tomography images. External force was applied to the 5 metacarpals in neutral position and to the palm in extended position. Force transmissions through the carpus and ligament tension in extended position were compared with those in neutral position, and force distributions were compared in each position.

RESULTS

Force transmission ratio on the scaphoid fossa significantly increased from 52% in neutral to 62% in extension (p< .05), whereas the ratio through the lunate fossa decreased from 42% to 36%. In the midcarpal joint, force to the scaphoid significantly increased from 60% to 69% (p< .05). Force distributions of the radiocarpal joint in the extended position moved on the center of the lunate fossa and interfossal ridge of the scaphoid fossa. The dorsal ridge of the radial articular surface appeared as the new contact area. Tension in 3 palmar intrinsic ligaments and the flexor retinaculum greatly increased in the extended position.

CONCLUSIONS

Force transmission in the extended position shifted radially, concentrating at the scaphoid. We could show how bending force causes scaphoid fracture and concentration of force on the radius surface might cause intra-articular fracture coinciding with the fracture pattern introduced by Melone. The palmar intrinsic ligaments appear key to maintaining the carpal arch in push-up position. Our theoretical analysis could well explain several patterns of wrist injuries.

Scaphoid excision with four-corner fusion: a biomechanical study

PURPOSE

Partial wrist arthrodesis is a commonly performed procedure for the treatment of posttraumatic wrist arthritis because of its ability to provide pain relief without sacrificing complete wrist motion. The purpose of this study was to evaluate the redistribution of force after four-corner fusion and scaphoid excision, and to correlate the findings with the reported clinical outcomes.

METHODS

Fifteen cadaveric wrists were used to study the biomechanics of the four-corner fusion. Pressure-sensitive film (super-low-pressure-indicating film-Pressurex, Sensor Products Inc, Madison, NJ) was inserted into the radiocarpal joint. Using the MTS 858 Mini Bionix (MTS System, Eden Prairie, MN), 50-kg loads (220 N) were applied to the wrists before and after simulated four-corner fusion and scaphoid excision. Statistically, we compared the pressure in the normal (intact) wrists versus four-corner fusion and scaphoid excision. The pressure measurements across the scaphoid fossa, lunate fossa, and triangular fibrocartilage complex (TFCC) were compared.

RESULTS

There is a statistical significant difference between scaphoid, lunate, and TFCC mean total force when pre and post-fusion were compared (p = 0.0001). Our study revealed a statistical significant decrease in the mean scaphoid total force after scaphoid excision and four-corner fusion (p = 0.0001). We also found a subsequent increase in mean total force after scaphoid excision and four-corner fusion for the lunate fossa that did not reach statistical significance (p = 0.08), and no difference in load across the TFCC area (p = 0.995).

CONCLUSIONS

Our findings suggest that load is preferentially transferred to the radiolunate joint after scaphoid excision with four-corner fusion.

Pisotriquetral dysfunction following limited and total wrist arthrodesis

PURPOSE

We report a series of pisotriquetral arthritis cases following wrist and intercarpal arthrodesis, offer an anatomic and biomechanical rationale, and introduce intraoperative considerations to avoid this potential complication.

METHODS

Nine patients with pisotriquetral arthritis requiring pisiform excision following wrist and intercarpal arthrodesis were retrospectively evaluated at 2 institutions. Five paired cadaver wrists were tested for alterations in pressure and kinematics of the pisotriquetral joint following four-corner and total wrist fusions.

RESULTS

Nine patients were successfully treated with pisiform excision for pisotriquetral arthritis following wrist and intercarpal fusions. Biomechanical cadaver testing demonstrated profound alterations in pisotriquetral kinematics and pressure changes in measured degrees of wrist position following wrist and intercarpal fusions.

CONCLUSIONS

Patients undergoing four-corner and/or wrist arthrodesis should be assessed for pisotriquetral discomfort before surgery, including a physical examination and a 30 degrees supinated radiograph to look for degenerative changes. Attempts should be made intraoperatively to ensure that the proximal row is not fused in an extended position. After surgery, if discomfort develops and conservative treatment fails, then pisiform excision can successfully alleviate the pain.

Carpal kinematics during simulated active and passive motion of the wrist

PURPOSE

The purpose of this study was to investigate the effect of experimental control mechanisms, simulated active (tendon-driven) and passive (externally assisted), on carpal motion.

METHODS

Kinematics of the carpal bones in five fresh-frozen cadaver upper extremities were studied using an optical motion analysis system. The wrist extensors and flexors were dissected and loaded. For passive motion, the tendons were loaded to simulate muscle tone while the investigator passively moved the wrist using a pin placed in the third metacarpal. To simulate active, patient-driven motion, the tendons were attached directly to guide bars while the investigator used a puppeteer mechanism to move the wrist.

RESULTS

There were no significant differences in carpal motion (flexion-extension motion or radial-ulnar deviation) when the wrist was moved in simulated active motion through the extensor and flexor tendons or in passive motion, with a constant force applied to the tendons. Kinematics for simulated active motion, in general, was more difficult to control and was less smooth than the kinematics for passive motion.

CONCLUSIONS

Carpal bone kinematics (excluding the pisiform) in a healthy normal joint are similar in both simulated active (tendon-driven) and passive (externally assisted) wrist motion because the carpal bones are passively moved during wrist motion (there are no direct tendon-to-muscle attachments to the proximal carpal bones and minimal attachments to the distal carpal bones).

Contact area inside the distal radioulnar joint: effect of axial loading and position of the forearm

BACKGROUND

A biomechanical study was performed to define the normal profiles of contact area inside the distal radioulnar joint and how these profiles change as a result of damage to the distal radioulnar ligaments.

METHODS

Twelve cadaver arms were used and a custom-made jig was designed to allow axial loading of the hand. Tekscan sensor film was used to measure the contact area inside the joint. Measurements were taken with different loads and in different positions of the forearm. The same measurements were taken after dividing either the volar or dorsal distal radioulnar ligament. Finally the measurements were repeated after reconstruction of the divided ligament.

FINDINGS

The contact area increases with axial loading of the hand and is greater in supination than pronation. Division of a single distal radioulnar ligament increases the contact area inside the distal radioulnar joint (123% of normal) and reconstruction of the divided distal radioulnar ligament restores the contact patterns towards the normal values (113% of normal).

INTERPRETATION

The results show that axial loading of the hand and position of the forearm has a significant effect on the contact area inside the distal radioulnar joint. The study also shows that injury of the distal radioulnar ligament disturbs the normal profiles of contact.

Intra-articular pressure measurement in the radioulnocarpal joint using a novel sensor: in vitro and in vivo results

PURPOSE

To determine the amount and distribution of forces transmitted across the human radioulnocarpal joint under physiologic conditions in vivo. We performed an in vitro validation of a specifically developed capacitive pressure-sensor device and an in vivo measurement of force transmission and pressure distribution at the radioulnocarpal joint in a healthy volunteer.

METHODS

A new capacitive pressure-sensor device was adapted for intra-articular pressure measurement in the human radioulnocarpal joint. The technical characteristics of the device were determined and the sensor was validated in fresh-frozen cadaver tests. Force transmission across the radioulnocarpal joint then was measured in healthy volunteers under local anesthesia.

RESULTS

The sensor delivered reproducible measurements of forces across the radioulnocarpal joint and their distribution in the cadaver experiment. In vivo, 2 centers of force transmission were identified. None of these centers correlated with previous findings in the literature. More force is transmitted across the ulnar side of the radioulnocarpal joint than previously thought. The results are consistent with clinical findings.

CONCLUSIONS

The novel sensor device is suitable for intra-articular pressure measurement in the human radioulnocarpal joint in vitro and in vivo.

The effect of radial shortening on wrist joint mechanics in cadaver specimens with inherent differences in ulnar variance

PURPOSE

To assess load changes in the wrist and forearm resulting from surgically-induced radial shortening in wrists with inherent differences in ulnar variance.

METHODS

Eleven fresh cadaver upper extremities, 4 with ulnar-plus variance of 2 mm or greater and 7 with ulnar-minus variance of 2 mm or greater were used. The radius and ulna of each specimen were instrumented with load cells, a 15-mm segment of the radius was resected and replaced with aluminum blocks of various sizes, and the specimens were loaded with 143 N (32 lb) at 1-mm differences of radial length. The load distribution between the radius and ulna was measured.

RESULTS

The load distribution in the specimens with an ulnar-plus variance averaged 69% through the radius and 31% through the ulna. In the wrists with ulnar-minus variance, the load distribution averaged 94% through the radius and 6% through the ulna. The mean force in the ulna increased and the mean force in the radius decreased with incremental shortening of the distal end of the radius. The mean force through the ulna in the ulnar-plus-variance group was always higher than that of the ulnar-minus-variance group. When compared not by the number of millimeters of radial shortening but by the adjusted ulnar variance, there was no difference between the ulnar-plus-variance and the ulnar-minus-variance groups.

CONCLUSIONS

Wrists with ulnar-minus variance could accommodate radial shortening without as much increase in the ulna load as wrists with ulnar-plus variance. The clinical relevance is that a patient with an ulnar-minus variance may accommodate more radial shortening after a wrist fracture without developing an ulnar impaction syndrome than a patient with an ulnar-plus-variant wrist.

Fractures récentes du scaphoïde (moins de trois semaines)

Scaphoid fractures are the most common carpal fracture, accounting for 70 a 80% of all fractures of the wrist. The diagnosis of acute fracture of the scaphoid still continues to be missed despite an increasing improvement of imaging techniques. In fact, these fractures are mainly neglected because of minimal early symptoms or quick resolution of initial symptoms. X-ray analysis of acute fractures is rather difficult because of the irregular shape of the scaphoid and its overlapping with other structures. In case of doubtfull or negative initial radiographic views, a technetium 99 bone scan or MR imaging should be consisidered. These fractures occuring in the young and most active members of our society represents a population that doesn't have the patience for traditionnal immobilisation in cast. Thus patients with undisplaced fractures for whom early return to work or sport is a primary concern, percutaneous repair with cannulated screw fixation using fluoroscopy and even aided with arthroscopy represents an increasing option. Nevertheless, in thoses cases, cast immobilisation should always be first considered. If percutaneous internal fixation is the first choice in proximal pole fractures or fractures seen with a delay, in the other cases, it can only be advocated if internal fixation will provide a stable reduction. There is little controversy for the treatment of displaced unstable scaphoid fractures. Open repair and internal fixation with a screw represents the golden standard. Complex displaced or dislocated fractures are often comminuted and associated with bony defect. Accurate reduction may need to perform a bone graft. The ligamentous injuries should also be carefully repaired . Evidence of associated cartilagenous lesions must be asessed with precision, as they always jeopardize the end result.

Changes in radiocarpal loading characteristics after proximal row carpectomy

PURPOSE

To document the changes in wrist loading that occur after proximal row carpectomy in a cadaver model.

METHODS

The normal radioulnar carpal pressure distributions of 7 cadaver wrists were measured using super-low-pressure-sensitive film. Proximal row carpectomies were performed and the loading characteristics re-evaluated.

RESULTS

In the lunate fossa the contact area increased 37%, the average contact pressure increased 57%, and the location of the contact moved radially 5.5 mm. With wrist motion between 40 degrees of extension and 20 degrees of flexion the volar/dorsal excursion of the lunate fossa contact point increased by 108%.

CONCLUSIONS

Significant changes in radiocarpal loading occur after proximal row carpectomy. The increased radiocarpal excursion with wrist motion may explain the low incidence of radiocapitate arthritis in patients who have had proximal row carpectomy.

Assessment of articular displacement of distal radius fractures

Intraarticular step and gap displacements represent the most common indication for surgical treatment of distal radius fractures. Most often, treatment decision making relies only on good-quality plain radiographs taken before and after reduction with measurement accuracy maximized by using the longitudinal axis method. When plain radiographs alone prove insufficient, CT scans or tomograms will significantly improve interobserver and intraobserver reliability of measurements, especially when evaluated using the arc method. Tomography is an effective method for postoperative evaluation of fractures immobilized in splints or casts. The role of MRI in assessing intraarticular distal radius fractures is limited to confirming injuries to carpal ligaments or the triangular fibrocartilage complex. Intraoperatively, we use fluoroscopy to obtain 30 degrees cephalad posteroanterior views and as 22 degrees lateral views to best observe articular surface reduction. Our current operative indications include fractures with radiocarpal or distal radioulnar joint step or gap deformities greater than 1-2 mm, gross distal radioulnar joint instability, or those with extensive metaphyseal comminution rendering them particularly unstable after closed reduction. In general, we tend to lean toward operative fixation in younger, more active patients.

Treatment of isolated perilunate and lunate dislocations with combined dorsal and volar approach and intraosseous cerclage wire

PURPOSE

To determine the clinical outcome of patients with perilunate and lunate dislocations treated with a combined dorsal and volar approach and intraosseous cerclage wire.

METHODS

A combined dorsal and volar approach with an intraosseous wiring technique was used to treat 22 isolated perilunate and lunate dislocations. The mean interval between injury and surgery was 3 days. Outcome was assessed after an average of 49 months. Patients were assessed subjectively with a Disabilities of the Arm, Shoulder, and Hand questionnaire and were asked to rate their overall satisfaction, pain relief, problems with activities of daily living, and return to work and previous activity status. Results were assessed objectively by range of motion and grip-strength measurements and initial postsurgical radiographs were compared with final radiographs with regard to scapholunate angle and gap.

RESULTS

Patient satisfaction was high in 15 of 22 patients. Seven patients stated they had problems with activities of daily living after their injury. Only 10 patients returned to the same job they had before their injury; however, all 22 patients were able to return to some type of work. Sixteen of the patients stated they were able to return to their previous level of activity. The wrist flexion-extension arc and grip strength averaged 80% and 77%, respectively, compared with the opposite side. Follow-up radiographs showed no significant change in scapholunate angle or gap with time. As expected the scapholunate cerclage wire broke frequently. The cerclage wire was removed in 16 patients, 12 because of broken hardware and 4 because of pain.

CONCLUSIONS

Our results show that a combined dorsal and volar approach with an intraosseous wiring technique can restore effectively normal intercarpal relationships, providing acceptable pain relief, functional motion, and grip strength.

The distal radioulnar joint as a load-bearing mechanism--a biomechanical study

PURPOSE

A biomechanical study was performed to define the normal profiles of force transmission across the distal radioulnar joint (DRUJ) and their alteration as the result of surgical modification of the joint and its ligaments.

METHODS

Twelve cadaver arms were used in this investigation. A custom-made jig was designed to hold the arm and allow axial loading of the hand. Force transmitted across the DRUJ was measured with sensor film. The axial force transmitted through the ulna and radius was measured with strain gauges mounted to the surface of each bone and the strain in the dorsal and volar distal radioulnar ligaments (DRUL) was measured with differential variable reluctance transducers. Measurements of force and strain with the DRUJ in the surgically unmodified condition were performed in various positions of forearm rotation and with sequential loads. Subsequently, the same series of measurements was performed after DRUL division and after reconstruction of the ligament. The effect of excision of the ulna head (Darrach's procedure) was also studied.

RESULTS

Force varied significantly (p <.05) with the applied load and with forearm position, being greater in supination than pronation (sensor film data). Force transmitted through the ulna varied in an approximately reciprocal pattern with that of the radius. The greatest forces through the ulna occurred in supination and therefore mirrored the change in force transmission across the DRUJ. Between 32% and 34%, respectively, of the applied load (5-10 kg) was transmitted through the ulna and the remainder was transmitted through the radius (strain gauge data). Division of either the volar or the dorsal DRUL tended to increase the force transmitted across the DRUJ (p =.09), and reconstruction of the disrupted DRUL restored the force pattern toward the previous values (not significant) (differential variable reluctance transducer data). Excision of the ulna head disrupted the force transmission profiles, producing the biomechanical equivalent of a 1-bone forearm. Only 1.8% and 2.7% of the applied force (10 kg and 5 kg), respectively, was transmitted through the ulna (strain gauge data only).

CONCLUSIONS

The data show consistent and characteristic force transmission profiles across the DRUJ and through both ulna and radius. The joint is important in the transmission of load and its anatomic integrity should be respected in surgical procedures if normal biomechanics are to be preserved.

Fixation stability of comminuted humeral shaft fractures: locked intramedullary nailing versus plate fixation

BACKGROUND

This study compared the fixation stability of two treatments for humeral shaft fractures with segmental bone loss during cyclic, physiologic loading.

METHODS

Six matched pairs of human humeri received either a 10-hole broad dynamic compression plate or a locked antegrade inserted humeral nail applied to a humeral diaphyseal osteotomy with a 1.5-cm gap defect. The bone-implant humeral constructs were axially loaded for 10,000 cycles at 250 N and 500 N, with measurements of gap displacement and calculation of construct stiffness. The specimens were then loaded to failure.

RESULTS

Cyclic loading showed no difference between the two groups for average gap displacement or construct stiffness. The intramedullary nail constructs failed by humeral shaft splitting (n = 4) or head cut-out (n = 2) at an average of 958.3 N, whereas the plate constructs failed by humeral shaft splitting and screw pull-out (n = 3) or plate bending (n = 3) at an average of 641.7 N (p < 0.001).

CONCLUSION

Although both methods offer similar fixation stability under physiologic loads, the higher load to failure demonstrated by intramedullary nail fixation may have implications for the patient with multiple injuries for whom partial weightbearing on the injured upper extremity may be necessary.

Computer simulation of the upper extremities

The development of real-time, interactive, three-dimensional, computer graphic simulation of the musculoskeletal system with emphasis on the upper extremities is described. Developments in image analysis, scientific visualization, and interactive computer methods and the continuous improvement in knowledge of musculoskeletal function have combined to provide an exciting new tool for musculoskeletal research. Interactive simulation also has promising applications in medical education and clinical rehabilitation. Only those developments that fit the specific criteria of realism, real-time response, intuitive interaction, three-dimensional structures, and modeling flexibility are discussed. It is hoped that an improved understanding of this emerging tool and an appreciation for its potential applications will be gained.

Distal radial metaphyseal forces in an extrinsic grip model: implications for postfracture rehabilitation

The purpose of this study was to establish the relationship between force at the distal radius and power grip force of the hand, a common functional and rehabilitation maneuver. This information will provide limits of allowable grip forces during postfixation rehabilitation and guide design requirements for fixation systems. By designing a model of power grip using the extrinsic hand musculotendinous units, we were able to compare grip force with force at the distal radius. Our results show that to obtain 10 N of grip force, approximately 26.3 N of force is transmitted through the distal radius, 52.4 N is transmitted through the radius and ulna combined, and 30.0 N needs to be applied to the flexor tendons. Fifty-one percent of the total forearm force was transmitted through the distal radius in this model. If all forearm forces were transmitted through the radius, 52 N of force would be transmitted through the distal radius to obtain 10 N of grip force. The clinical application of this model suggests that since failure forces of tested distal radius fixation systems range from 55 to 825 N, rehabilitation grip force should not exceed 10 to 159 N, depending on the type of fixation.

Altered patterns of subchondral bone mineralization in Kienböck's disease

The pattern of subchondral bone density, which is supposed to reflect the long-term distribution of stress, was investigated in both wrist joints of nine healthy young subjects and seven patients suffering from Kienböck's disease by means of CT osteoabsorptiometry. Two density maxima were found on the distal articular surface of the radius in the healthy subjects, corresponding to the position of the scaphoid and the lunate. Our relative quantitative results showed three different physiological types of stress indicated by the predominantly monocentric density maxima either on the scaphoid or the lunate surface of the radius and the symmetrical distribution of the mineralization. In Kienböck's disease no type of mineralization predominated. In the progressive stages the lunate density maximum was absent. The overall mineralization was generally less than in controls. Changes in the pattern of mineralization were also found on the contralateral side.

Contact stress distributions in malreduced intraarticular distal radius fractures

Residual articular incongruity of the distal radius following intraarticular fracture has been correlated with early osteoarthritis (OA) and a poor clinical outcome. We developed a simple in vitro fracture model of the distal radius to investigate the relationship between degree of articular incongruity and the resulting distribution of radiocarpal contact stress. Twelve fresh-frozen cadaver arms were dissected, packets of Fuji Pressensor film were inserted into the wrist, and the wrist was loaded through its flexor and extensor tendons. We created a simple intraarticular fracture that allowed controlled distal radius articular incongruity. Loading trials were performed for the intact distal radius, for a fully reduced case, and for step-offs of 0.4, 1, 2, and 3 mm. Mean contact stress was significantly greater than the anatomically reduced case at only 3 mm of step-off. Contact area was greater than the anatomically reduced case at 0.4, 1, and 2 mm of step-off. The elevations in contact stress that we observed were only modest, suggesting that other factors may be involved in the pathogenesis of radiocarpal OA in the presence of residual articular incongruity.

Force and pressure transmission through the normal wrist. A theoretical two-dimensional study in the posteroanterior plane

Force transmission through the wrist in the normal population was investigated using the rigid body spring modeling (RBSM) technique (assuming carpal bones are rigid bodies interposed by series of springs simulating articulating cartilage and constraining ligaments). One-hundred and twenty normal wrist posteroanterior X-rays of adults (evenly divided to represent both genders and two age groups) provided the anatomical data. Reaction forces between the carpal bones were modeled using a system of compression linear springs, representing cartilage and subchondral bone, and of tensile linear springs, representing ligaments. The spring constants were determined based on the material properties of wrist cartilage and ligaments. Assumed axial loads were applied along the metacarpals to simulate a grasp strength of 10 N with active stabilization of the wrist in neutral position. The force transmission ratio at the radio-ulno-carpal joint was 55% through the radio-scaphoid and 35% through the radio-lunate joints. The remaining 10% of the load was passing through the triangular fibrocartilage with minor differences between genders. Among the intercarpal joints, a large percentage of the load of the wrist was transmitted to the scaphoid. The peak pressure was highest at the proximal pole of the radio-scaphoid, with a radio-scaphoid versus radio-lunate peak pressure ratio of 1.6. The most important ligaments in terms of load transmission were those opposing ulnar translation of the carpus. The wrist morphology had little influence on the magnitude and pattern of load distribution. There was no effect of age on wrist force distribution.

Biomechanics of the wrist

This article summarizes six years of studies with an experimental model, which uses a static positioning frame, pressure-sensitive film, and a microcomputer-based videodigitizing system, to characterize the biomechanics of the human cadaver wrist by measuring the contact areas and pressures in a variety of normal, simulated traumatic, and surgically treated conditions. The results of these studies have provided clinically relevant information about the normal anatomy and functional mechanics of the wrist, as well as guidelines for the treatment for a number of different fractures and ligament injuries. The results of studies of radial carpal instabilities and fractures have demonstrated an increased load in the areas where degenerative arthritis is seen in these clinical conditions, and have furnished a means by which the biomechanical efficacy of certain surgical treatments can be measured.

Extrinsic wrist ligaments in the pathomechanics of ulnar translation instability

A description of the various combinations of ligament disruptions necessary for ulnar translation instability is presented based on a series of cadaver dissections and load studies. Dissections and load studies demonstrated that major ligament disruption, even to the extent that only the dorsal ulnolunate, the palmar ulnolunate or the radioscaphocapitate, and the long radiolunate ligaments were left intact, failed to result in meaningful ulnar translation of the carpus. The radioscaphocapitate ligament alone could not prevent significant ulnar translation. Palmar translation instability was evident with less ligament disruption than that needed for ulnar translation and was always evident if there was ulnar translation. These studies imply that ulnar translation represents a much more global ligament disruption and instability than previously suggested in the literature.

Malunited Colles' fracture. Analysis of stress distribution

To try to explain disability in the wrist after malunited Colles' fractures, an experiment was designed to evaluate pressure distribution through the wrist joint with varying degrees of angulation of the distal radius. The results of computer simulation analysis of stress concentration using finite element methods were compared with those of pressure distribution studies on the radial articular surface of cadaveric radii in various positions using pressure-sensitive film. Stress existed in volar regions of the radio-lunate joint under normal pressure in the neutral position, but shifted to dorsal regions of the joint, and was concentrated when dorsal angulation reached 30 degrees. We believe that concentrated loads result in pain and may lead to early degenerative joint disease. Early additional reduction of a displaced fragment or a post-fusion osteotomy should be considered when dorsal angulation exceeds 30 degrees in malunited distal radial fractures to decrease abnormal loading across the wrist joint.

Measurement of carpal bone geometry by computer analysis of three-dimensional CT images

The aim of this project was noninvasively to analyze and quantitate the geometry, load transfer characteristics, and spatial relationships of the carpal bones by using a new three-dimensional CT scan reconstruction technique. The determination of mechanical parameters such as distances between centroids and between bone surfaces, carpal alignment, volumes, surface areas, and contact areas can provide the basis for comparison between normal wrists and wrists with a variety of progressive instability patterns, types of fracture, pathologic and posttraumatic states, and different simulated surgical procedures. This new technology has demonstrated a volumetric accuracy of 94% and a linear accuracy of 97%. Simultaneous analysis of all articulating surfaces of multiple joints can be performed in cadavers and in patients because of the noninvasive nature of the imaging reconstruction technique. This new research offers much more information than has previously been available. It also promises direct application to the clinical setting and eliminates several limitations and questions that were inescapable with previous technology.

Load mechanics of the midcarpal joint

The midcarpal joint was studied in upper extremities of fresh cadavers with the use of a static positioning frame, pressure-sensitive film, and a microcomputer to analyze the contact prints. The contact area on the proximal side of the midcarpal joint was found to consist generally of four areas; the scaphoid-trapezium-trapezoid, the scaphoid-capitate, the lunate-capitate, and the triquetrum-hamate. The contact areas accounted for less than 40% of the available joint surface, even under loads of 118 pounds. The distribution of load through the midcarpal joint was scaphoid-trapezium-trapezoid 23%, scaphoid-capitate 28%, lunate-capitate 29%, and triquetrum-hamate 20%. The midcarpal joint, like the radiocarpal joint, appears to transmit load through distinct areas and through a relatively small portion of the available joint surface.

Force distribution across wrist joint: application of pressure-sensitive conductive rubber

A new pressure-sensitive conductive rubber sensor was used for investigation of the pressure distribution through the radio-ulno-carpal joint. Twelve of these transducers were placed in the radio-ulno-carpal joint. Pressure was measured in seven different wrist positions under loads incrementally increasing from 0 to 12 kg. Half of the sensors showed less than 0.5 MPa, even at maximum load, while a high-pressure area was located palmary in each fossa. The peak pressure measured in the wrist neutral position was 2.4 MPa on the scaphoid fossa, 1.5 MPa on the lunate fossa, and 1.1 MPa on the triangular fibrocartilage with a 10 kg load. The peak pressure ratio between the scaphoid and the lunate was 1.7 in the neutral wrist position. This increased in radial deviation to 2.9 and decreased in ulnar deviation to 0.8. The force-transmission ratio was 50% through the scaphoid fossa, 35% through the lunate fossa, and 15% through the triangular fibrocartilage in the neutral position. The advantage of this sensor is that it is thin and flexible and provides reliable reproducible quasi-instantaneous measurements.

Simulated scaphoid proximal pole fracture

Five fresh cadaver upper extremities were studied with use of a static positioning frame, pressure-sensitive film, a microcomputer-based videodigitizing system, and a Sun station image analysis system to assess the load bearing characteristics of the scaphoid in the proximal carpal joint. Specimens were studied in their normal condition, after a proximal pole osteotomy of the scaphoid, and after resection of the proximal pole of the scaphoid. The amount of contact area born through the scaphoid fossa was essentially the same whether the scaphoid was intact, or after a simulated scaphoid fracture of its proximal pole, or after resection of the proximal pole. The scaphoid contact area and pressure, although overall relatively constant, was redistributed after osteotomy, resulting in increased contact area under the distal fragment and no change or a slight decrease in the contact area under the proximal fragment of the scaphoid. After resection of the proximal fragment, all scaphoid contact area and pressure was born by the distal scaphoid fragment. The contact area and pressure characteristics of the lunate remained unchanged in all conditions compared with the normal condition. There were no significant changes in the locations of the centroids of the scaphoid segments and the lunate in any of the conditions tested.

Ulnar-sided perilunate instability: an anatomic and biomechanic study

A staging system for ulnar-sided perilunate instability is presented based on a series of cadaver dissections and load studies. Stage I: partial or complete disruption of the lunotriquetral interosseous ligament, without clinical and/or radiographic evidence of dynamic or static volar intercalated segment instability deformity; stage II: complete disruption of the lunotriquetral interosseous ligament and disruption of the palmar lunotriquetral ligament, with clinical and/or radiographic evidence of dynamic volar intercalated segment instability deformity; and stage III: complete disruption of the lunotriquetral interosseous and the palmar lunotriquetral ligaments, attenuation or disruption of the dorsal radiocarpal ligament, with clinical and/or radiographic evidence of static volar intercalated segment instability deformity.

Evaluation of the biomechanical efficacy of limited intercarpal fusions for the treatment of scapho-lunate dissociation

An experimental model that uses a static positioning frame, pressure-sensitive film, and a microcomputer-based videodigitizing system was used to measure the contact areas and pressures in a group of wrists in their "normal" state, after ligament sectioning, which resulted in stage III perilunate instability and then following different types of simulated carpal fusions. Compared with a normal wrist, there is an overall decrease in load in the lunate fossa and a significant increase in load in the scaphoid fossa in the wrist with stage III perilunate instability. Scaphoid-trapezium-trapezoid and scaphoid-capitate fusions transmitted almost all load through the scaphoid fossa. Scaphoid-lunate, scaphoid-lunate-capitate, and capitate-lunate fusions all distributed load more proportionately through both scaphoid and lunate fossae. The positioning of the carpal bones within a limited carpal fusion was also found to affect the load distribution in the wrist. The scaphoid-lunate, scaphoid-lunate-capitate, or capitate-lunate fusions, with attention to the relative carpal alignment within the limited fusion seem to offer more promise for treatment of perilunate instability biomechanically than the scaphoid-trapezium-trapezoid or scaphoid-capitate fusions.