The streaming potential method for the characterization of ultrafiltration organic membranes and the control of cleaning treatments

Influence of Pore-Size/Porosity on Ion Transport and Static BSA Fouling for TiO2-Covered Nanoporous Alumina Membranes

The influence of geometrical parameters (pore radii and porosity) on ion transport through two almost ideal nanoporous alumina membranes (NPAMs) coated with a thin TiO2 layer by the atomic layer deposition technique (Sf-NPAM/TiO2 and Ox-NPAM/TiO2 samples) was analyzed by membrane potential and electrochemical impedance spectroscopy measurements. The results showed the significant effect of pore radii (10 nm for Sf-NPAM/TiO2 and 13 nm for Ox-NPAM/TiO2) when compared with porosity (9% and 6%, respectively). Both electrochemical techniques were also used for estimation of protein (bovine serum albumin or BSA) static fouling, and the results seem to indicate deposition of a BSA layer on the Sf-NPAM/TiO2 fouled membrane surface but pore-wall deposition in the case of the fouled Ox-NPAM/TiO2 sample. Moreover, a typical and simple optical technique such as light transmission/reflection (wavelength ranging between 0 and 2000 nm) was also used for membrane analysis, showing only slight transmittance differences in the visible region when both clean membranes were compared. However, a rather significant transmittance reduction (~18%) was observed for the fouled Sf-NPAM/TiO2 sample compared to the fouled Ox-NPAM/TiO2 sample, and was associated with BSA deposition on the membrane surface, thus supporting the electrochemical analysis results.

Effect of Polysaccharide Conformation on Ultrafiltration Separation Performance

The manifold array of saccharide linkages leads to a great variety of polysaccharide architectures, comprising three conformations in aqueous solution: compact sphere, random coil, and rigid rod. This conformational variation limits the suitability of the commonly applied molecular weight cut-off (MWCO) as selection criteria for polysaccharide ultrafiltration membranes, as it is based on globular marker proteins with narrow M_w and hydrodynamic volume relation. Here we show the effect of conformation on ultrafiltration performance using randomly coiled pullulan and rigid rod-like scleroglucan as model polysaccharides for membrane rejection and molecular weight distribution. Ultrafiltration with a 10 kDa polyethersulfone membrane yielded significant different recoveries for pullulan and scleroglucan showing 1% and 71%, respectively. We found deviations greater than 77-fold between nominal MWCO and apparent M_w of pullulan and scleroglucan, while recovering over 90% polysaccharide with unchanged M_w. We anticipate our work as starting point towards an optimized membrane selection for polysaccharide applications.

Ups and Downs of Water Photodecolorization by Nanocomposite Polymer Nanofibers

Given the exponentially expanding water pollution causing water scarcity, there is an urgent need for operative nanotechnological systems that can purify water, with insignificant energy consumption, and rapidly. Here, we introduce a nanocomposite system based on TiO₂ nanoparticles (NPs) and PES nanofibers (NFs) that can adsorb and then photodecompose organic water pollutants such as dye molecules. We evaluate pros and cons of this system with respect to its purification efficiency and structural properties that can be impacted by the photocatalytic activity of the nanofillers. While the material is superhydrophilic and able to remove 95% methylene blue (MB) from water via adsorption/photodecomposition, its thermomechanical properties decline upon UV irradiation. However, these properties still remain at the level of the neat NFs. The removal behavior is modeled by the first- and second-order kinetic models from the kinetic point of view. The nanocomposite NFs’ removal behavior complies much better with the second-order kinetic model. Overall, such feedbacks implied that the nanocomposite can be effectively applied for water treatment and the structural properties are still as reliable as those of the neat counterpart.

Preparation and characterization of a pH-responsive membrane carrier for meso-tetraphenylsulfonato porphyrin

The pH-responsive PSF-g-P4VP-blended PSF membrane smartly rejects meso-tetraphenylsulfonato porphyrin (TPPS) and induces TPPS to form J-type aggregates.

A Novel Nanohybrid Nanofibrous Adsorbent for Water Purification from Dye Pollutants

In this study, we devised a novel nanofibrous adsorbent made of polyethersulfone (PES) for removal of methylene blue (MB) dye pollutant from water. The polymer shows a low isoelectric point thus at elevated pHs and, being nanofibrous, can offer a huge highly hydroxylated surface area for adsorption of cationic MB molecules. As an extra challenge, to augment the adsorbent’s properties in terms of adsorption capacity in neutral and acidic conditions and thermal stability, vanadium pentoxide (V₂O₅) nanoparticles were added to the nanofibers. Adsorption data were analyzed according to the Freundlich adsorption model. The thermodynamic parameters verified that only at basic pH is the adsorption spontaneous and in general the process is entropy-driven and endothermic. The kinetics of the adsorption process was evaluated by the pseudo-first- and pseudo-second-order models. The latter model exhibited the highest correlation with data. In sum, the adsorbent showed a promising potential for dye removal from industrial dyeing wastewater systems, especially when envisaging their alkaline and hot conditions.

Facile real-time evaluation of the stability of surface charge under regular shear stress by pulsed streaming potential measurement

The applicability of the pulsed streaming potential measurement for real-time evaluation of stability of assembled layers based on the relative zeta potential change rate S_R was demonstrated.

Chemical cleaning/disinfection and ageing of organic UF membranes: a review

Membrane separation processes have become a basic unit operation for process design and product development. These processes are used in a variety of separation and concentration steps, but in all cases, the membranes must be cleaned regularly to remove both organic and inorganic material deposited on the surface and/or into the membrane bulk. Cleaning/disinfection is a vital step in maintaining the permeability and selectivity of the membrane in order to get the plant to its original capacity, to minimize risks of bacteriological contamination, and to make acceptable products. For this purpose, a large number of chemical cleaning/disinfection agents are commercially available. In general, these cleaning/disinfection agents have to improve the membrane flux to a certain extent. However, they can also cause irreversible damages in membrane properties and performances over the long term. Until now, there is considerably less literature dedicated to membrane ageing than to cleaning/disinfection. The knowledge in cleaning/disinfection efficiency has recently been improved. But in order to develop optimized cleaning/disinfection protocols there still remains a challenge to better understand membrane ageing. In order to compensate for the lack of correlated cleaning/disinfection and ageing data from the literature, this paper investigates cleaning/disinfection efficiencies and ageing damages of organic ultrafiltration membranes. The final aim is to provide less detrimental cleaning/disinfection procedures and to propose some guidelines which should have been taken into consideration in term of membrane ageing studies. To carry out this study, this article will detail the background of cleaning/disinfection and aging membrane topics in a first introductive part. In a second part, key factors and endpoints of cleaning/disinfection and aging membranes will be discussed deeply: the membrane role and the cleaning parameters roles, such as water quality, storing conditions, cleaning/disinfection/aging agents/conditions/protocols. The third and last part will be developed the parameters, methods and ways of characterization at our disposal and commonly used to develop and implement membrane cleaning and/or ageing studies.

Influence of hydrophobic effects on streaming potential

We study the influence of hydrophobic effects on streaming potential mediated flow through a narrow confinement. In a clear departure from the approach used in prior works, we use a phase-field model to capture the hydrophobicity-induced depletion in the near wall region, and express the variation of viscosity and permittivity across the interfacial layer in terms of the phase-field variable. We then use these in the determination of the flow velocity, and highlight the sensitive interplay between the intrinsic length scale of the electrical double layer and that of the depletion in terms of the variations of an effective normalized viscosity that captures the electroviscous effect. We expect that this work will be an important step forward in the realistic continuum modeling of interfacial physics in the particular context of streaming potential mediated flows.

Ion-Exchange Membranes Prepared Using Layer-by-Layer Polyelectrolyte Deposition

Layer-by-layer polyelectrolyte adsorption in porous polymeric membranes provides a simple way to create ion-exchange sites without greatly decreasing hydraulic permeability (<20% reduction in permeability). At 80% breakthrough, membranes coated with 3-bilayer poly(styrene sulfonate) (PSS)/polyethyleneimine (PEI) films bind 37±6 mg of negatively charged Au colloids per mL of membrane volume. The binding capacity of membranes coated with 1-bilayer films decreases in the order PSS/PEI>PSS/poly(diallyldimethyl ammonium chloride)>PSS/poly(allylamine hydrochloride). Films terminated with a polyanion present cation-exchange sites that bind lysozyme, and the lysozyme-binding capacities of (PSS/PEI)(3)/PSS films increase with the ionic strength of the solution from which the last PSS layer is deposited. Charge screening during deposition of the terminal PSS layer gives rise to a larger number of ion-exchange sites and lysozyme binding capacities as high as 16 mg per mL of membrane. At 10% breakthrough, a stack of 3 membranes binds 3 times as much lysozyme as a single membrane, showing that stacking is an effective way to increase capacity.

Asymmetric flow field flow fractionation of aqueous C60 nanoparticles with size determination by dynamic light scattering and quantification by liquid chromatography atmospheric pressure photo-ionization mass spectrometry

A size separation method was developed for aqueous C60 fullerene aggregates (aqu/C60) using asymmetric flow field flow fractionation (AF4) coupled to a dynamic light scattering detector in flow through mode. Surfactants, which are commonly used in AF4, were avoided as they may alter suspension characteristics. Aqu/C60 aggregates generated by sonication in deionized water ranged in size from 80 to 260 nm in hydrodynamic diameter (Dh) as determined by DLS in flow through mode, which was corroborated by analysis of fractions by DLS in batch mode and by TEM. The mass of C60 in each fraction was determined by LC-APPI-MS. Only 5.2+/-6.7% of the total aqu/C60 mass had Dh less than 80 nm, while 58+/-32% of the total aqu/C60 mass had Dh between 80 and 150 nm and 14+/-9.2% of the total aqu/C60 were between 150 and 260 nm in Dh. With the optimal fractionation parameters, 77+/-5.8% of the aqu/C60 mass eluted from the AF4 channel, indicating deposition on the AF4 membrane had occurred during fractionation; use of alternative membranes did not reduce deposition. Channel flow splitting increased detector response although channel split ratios greater than 80% of the channel flow led to decreased detector response. This is the first report on the use of AF4 for fractionating a colloidal suspension of aqu/C60.

Influence of steric, electric, and dielectric effects on membrane potential

The membrane potential arising through nanofiltration membranes separating two aqueous solutions of the same electrolyte at identical hydrostatic pressures but different concentrations is investigated within the scope of the steric, electric, and dielectric exclusion model. The influence of the ion size and the so-called dielectric exclusion on the membrane potential arising through both neutral and electrically charged membranes is investigated. Dielectric phenomena have no influence on the membrane potential through neutral membranes, unlike ion size effects which increase the membrane potential value. For charged membranes, both steric and dielectric effects increase the membrane potential at a given concentration but the diffusion potential (that is the high-concentration limit of the membrane potential) is affected only by steric effects. It is therefore proposed that membrane potential measurements carried out at high salt concentrations could be used to determine the mean pore size of nanofiltration membranes. In practical cases, the membrane volume charge density and the dielectric constant inside pores depend on the physicochemical properties of both the membrane and the surrounding solutions (pH, concentration, and chemical nature of ions). It is shown that the Donnan and dielectric exclusions affect the membrane potential of charged membranes similarly; namely, a higher salt concentration is needed to screen the membrane fixed charge. The membrane volume charge density and the pore dielectric constant cannot then be determined unambiguously by means of membrane potential experiments, and additional independent measurements are in need. It is suggested to carry out rejection rate measurements (together with membrane potential measurements).

Electrokinetic and surface chemical characterizations of an irradiated microfiltration polysulfone membrane: Comparison of two irradiation doses

The effect of ionizing radiation on the surface and electrokinetic characteristic parameters for a porous membrane of pore size 0.2 mum is determined and correlated with the irradiation dose (10 and 80 J/kg). Changes in NaCl permeability and membrane system electrical resistance determined from diffusion and impedance spectroscopy measurements are consistent with the increase of membrane pore radii/porosity, in agreement with SEM micrographs and reported results. Low irradiation dose seems to clean the membrane surface of impurities, according to XPS results, but the increase of irradiation doses could affect surface roughness. Due to the relatively high pore radius, ion transport numbers are practically independent of radiation and dose, but irradiation slightly modifies the membrane solution interface by increasing its weakly electronegative character, which could be of interest in the ultrafiltration of proteins or macromolecules.

Polymer-in-a-silica-crust membranes: macroporous materials with tunable surface functionality

We report on alkaline hydrolysis of tetraethoxysilane (Stöber synthesis) inside a macroporous polymer matrix resulting in a homogeneous coverage of silica onto the polymer surface. The encapsulation of the polymer struts by a continuous silica crust allows further functionalization with hydrophilic and hydrophobic silylating agents. The porous silica polymeric hybrid material combines the morphological control and mechanical flexibility of the polymeric matrix with the convenient surface modifications developed for glass and amorphous silica. This concept is applied to macroporous membranes where alteration in surface functionality allows tuning of hydrophobicity (contact angle and liquid entry pressure), streaming potential, and adsorption capacity of double-stranded DNA.

Modification of active and porous sublayers of aged polyamide/polysulfone composite membranes due to HNO3 treatment: Effect of treatment time

Changes in electrical and transport parameters for aged composite polyamide/polysulfone membrane samples (PAC) and their porous support layers (PSU) as a result of chemical treatment (immersion in 1 M HNO3 solution) at four different times (12 h < or = t < or = 72 h) have been obtained. Salt permeability, ion transport number, and membrane electrical resistance for the treated samples were determined from salt diffusion, membrane potential, and impedance spectroscopy measurements, which were carried out with the membranes in contact with NaCl solutions at different concentrations and compared with those determined for fresh and aged nontreated samples. Results show the strong effect of aging on membrane parameters, particularly the decrease in salt permeability (P(s)) and the increase in membrane electrical resistance (R(m)), while ion transport number is hardly affected by aging, chemical treatment, or treatment time. Results show how the compaction of the porous structure causes by aging (dried membrane matrix structure) can be partially reduced by HNO3 treatment, and they also allow the estimation of 24-h treatment as the optimum time (higher salt permeability and lower membrane electrical resistance), mainly for the polysulfone support layer. The use of equivalent circuits in the analysis of impedance spectroscopy data allows separate estimation of the electrical resistance associated with each sublayer of the composite PAC membrane samples. On the other hand, chemical changes in the active top layer of the PAC membrane (polyamide active layer) were obtained from XPS analysis, which show some modifications in the atomic concentration percentages of the polyamide characteristic elements as a result of acidic treatment time, which are more significant after 72-h acidic immersion.

Analysis of the pressure-induced potential arising through composite membranes with selective surface layers

When a pressure gradient is applied through a charged selective membrane, the transmembrane electrical potential difference, called the filtration potential, results from both the applied pressure and induced concentration difference across the membrane. In this work we investigate the electrokinetic properties relative to both active and support layers of a composite ceramic membrane close to the nanofiltration range. First, the volume charge density of the active layer is obtained by fitting a transport model to experimental rejection rates (which are controlled by the active layer only). Next, the value of the volume charge density is used to compute the theoretical filtration potential through the active layer. For sufficiently high permeate volume fluxes, the concentration difference across the active layer becomes constant, which allows assessing the membrane potential of the active layer. Experimental measurements of the overall filtration potential arising through the whole membrane are performed. The contribution of the support layer to this overall filtration potential is put in evidence. That implies that the membrane potential of the active layer cannot be deduced directly from the overall filtration potential measurements. Finally, the contribution of the support layer is singled out by subtracting the theoretical filtration potential of the active layer from the experimental filtration potential measured across the whole membrane (i.e., support + active layers). The amphoteric behavior of both layers is put in evidence, which is confirmed by electrophoretic measurements carried out with the powdered support layer and by recently reported tangential streaming potential measurements.

Effect of age and chemical treatments on characteristic parameters for active and porous sublayers of polymeric composite membranes

Changes in the transport parameters and the chemical nature of the surface of composite polyamide/polysulfone membranes due to both aging and treatment with chemical products (HCl, H(3)NO, and NaOH) have been considered. Hydraulic and salt permeability were obtained from water flow and salt diffusion measurements, respectively, and their values seem to indicate a modification in the structural parameters (porosity/thickness) of aging samples, while HCl and HNO(3) treatments will act in the opposite way. Chemical modifications in the membrane surfaces were studied by X-ray photoelectron spectroscopy (XPS), which mainly show the effect of H(3)NO and HCl on the polyamide active layer of the membranes (polyamide oxidation), but no chemical damage for that sublayer. Electrical characterization of both sublayers of the composite membranes were determined from impedance spectroscopy (IS) measurements using equivalent circuits as models, and these results indicate: (i) a strong increase of the membrane electrical resistance as a consequence of aging, mainly that associated with the active sublayer (30 times higher for an old sample than for a fresh one) and treatment with NaOH; (ii) the reduction of this effect when the samples were treated with HCl and HNO(3) solutions. Changes in the values of the electrical resistance of the composite membranes are in agreement with those obtained for permeabilities, but the electrical parameter also allows the determination of the contribution of each sublayer.

Effects of natural organic matter and ionic species on membrane surface charge

The surface charges of clean and natural organic matter (NOM)-adsorbed membrane surfaces of two different types of membranes (a UF and a NF membrane composed of the same material but having different pore sizes) were investigated. Concentrated NOM and its fractionated constituents were used as adsorbate and interacting macromolecules nearthe membrane surface. The zeta potential and the acidity of membranes were measured using electrophoresis and potentiometric titration methods, respectively, from the perspective of charge characterization, along with demonstration of ionic strength effects. The membrane surface was also characterized with attenuated total refractive Fourier transform infrared spectra to determine intrinsic functional groups and those changes before and after NOM adsorption. As a comparative study for the electrokinetic property of membrane, the zeta potentials for both examined polymeric membranes were determined by the electrophoresis and the streaming potential measurement methods as functions of ionic strength and the pH of measuring solution. Selectivity tests were performed to decide the relative importance of charge valence of cation in terms of the surface charge of membrane. It was demonstrated that divalent cations (Ca2+, Mg2+) increase zeta potentials relatively compared to monovalent cations (Na+, K+) because divalent cations have a greater potential in approaching membrane surfaces (i.e., inside the Stern layer). Thus, divalent cations can provide a greater double layer compaction and, when near the shear plane (available for both the zeta potential measurement methods), exist to a lesser extent than monovalent cations.

Determining the Zeta Potential of Porous Membranes Using Electrolyte Conductivity inside Pores

The zeta potential is an important and reliable indicator of the surface charge of membranes, and knowledge of it is essential for the design and operation of membrane processes. The zeta potential cannot be measured directly, but must be deduced from experiments by means of a model. The possibility of determining the zeta potential of porous membranes from measurements of the electrolyte conductivity inside pores (lambda(pore)) is investigated in the case of a ceramic microfiltration membrane. To this end, experimental measurements of the electrical resistance in pores are performed with the membrane filled with KCl solutions of various pHs and concentrations. lambda(pore) is deduced from these experiments. The farther the pH is from the isoelectric point and/or the lower the salt concentration is, the higher the ratio of the electrolyte conductivity inside pores to the bulk conductivity is, due to a more important contribution of the surface conduction. Zeta potentials are calculated from lambda(pore) values by means of a space charge model and compared to those calculated from streaming potential measurements. It is found that the isoelectric points are very close and that zeta potential values for both methods are in quite good agreement. The differences observed in zeta potentials could be due to the fact that the space charge model does not consider the surface conductivity in the inner part of the double layer. Measurements of the electrolyte conductivity within the membrane pores are proved to be a well-adapted procedure for the determination of the zeta potential in situations where the contribution of the surface conduction is significant, i.e., for small and charged pores. Copyright 2001 Academic Press.