Porous cellulose matrices containing lipophilic release modifiers--a potential oral extended-release system

Tailored beads made of dissolved cellulose--investigation of their drug release properties

In the frame of this work, we have investigated drug entrapping and release abilities of new type of porous cellulose beads (CBs) as a spherical matrix system for drug delivery. For that purpose, CBs prepared with three different methods were used as drug carriers and three compounds, anhydrous theophylline (Thp), riboflavin 5'-phosphate sodium (RSP) and lidocaine hydrochloride monohydrate (LiHCl) were used as model drug substances. The loading procedure was carried out by immersing swollen empty beads into the solutions of different concentrations of model drugs. The morphology of empty and loaded beads was examined using a field emission scanning electron microscopy (FE-SEM). Near-infrared (NIR) imaging was performed to identify the drug distributions on and within the loaded CBs. The drug amount incorporated into CBs was examined spectrophotometrically and in vitro drug release studies were performed to determine the drug release rates. The results of FE-SEM and chemical NIR imaging analyses revealed that incorporated drug were distributed on the surface and but also within the internal structure of the CBs. Physical properties of CBs and solubility of model drugs had effect on loading efficacy. Also, the drug release rates were controlled by solubility of model drugs (diffusion controlled release). In conclusion, CBs from dissolved cellulose show promise in achieving controlled drug delivery.

Novel/conceptual floating pulsatile system using high internal phase emulsion based porous material intended for chronotherapy

The aim of the present study was to design a novel/conceptual delivery system using ibuprofen, anticipated for chronotherapy in arthritis with porous material to overcome the formulation limits (multiple steps, polymers, excipients) and to optimize drug loading for a desired release profile suitable for in vitro investigations. The objective of this delivery system lies in the availability of maximum drug amount for absorption in the wee hours as recommended. Drug loading using 3(2) factorial design on porous carrier, synthesized by high internal phase emulsion technique using styrene and divinylbenzene, was done via solvent evaporation using methanol and dichloromethane. The system was evaluated in vitro for drug loading, encapsulation efficiency, and surface characterization by scanning electron, atomic force microscopy, and customized drug release study. This study examined critical parameters such as solvent volume, drug amount, and solvent polarity on investigations related to drug adsorption and release mostly favoring low-polarity solvent dichloromethane. Overall release in all batches ranged 0.98-52% in acidic medium and 71-94% in basic medium. These results exhibit uniqueness in achieving the least drug release of 0.98%, an ideal one, without using any release modifiers, making it distinct from other approaches/technologies for time and controlled release and for chronotherapy.

Drug release behaviour from methyl methacrylate-starch matrix tablets: effect of polymer moisture content

The aim of this work was to study the effect of the initial moisture content of the polymer on the tabletting and drug release behaviour of controlled release inert matrices elaborated with methyl methacrylate (MMA)-starch copolymers. The copolymers, obtained by free radical polymerisation and dried by two different methods (oven-drying or freeze-drying), were equilibrated at different relative humidities (0%, 25%, 50% and 75% RH) at room temperature. From these copolymers, matrix systems were directly compressed containing either a slightly water-soluble drug (anhydrous theophylline) or a freely water-soluble drug (salbutamol sulphate), and their compaction properties and in vitro dissolution profiles were evaluated. The release profiles were compared following model-independent methods, such as the Qt parameter and the similarity factor f2. Moreover, several kinetic models were employed to evaluate the possible changes in the release mechanism. For anhydrous theophylline, the initial moisture content of the copolymers did not affect the release characteristics from the inert matrices under study, and a typical Fickian diffusion mechanism was observed for the different formulations. However, in case of salbutamol sulphate, the presence of moisture might induce a fast drug dissolution, promoting the weakness of the matrix structure and hence, its partial disintegration. So, an "anomalous" mixed phenomenon of diffusion and erosion was found, influenced by the initial moisture content of the copolymer.

Influence of poloxamers on the dissolution performance and stability of controlled-release formulations containing Precirol ATO 5

Lipid excipients are usually used for the development of sustained-release formulations. When used in relatively high quantities, Precirol ATO 5 imparts sustained-release properties to solid oral dosage forms, by forming a lipid matrix. To control or adjust the drug release kinetics from such lipid matrix however, one must often resort to complementary ingredients or techniques. This study investigates the influence of poloxamers (Lutrol) included in lipid matrices composed of glyceryl palmitostearate (Precirol ATO 5) on their dissolution performance and their stability. The addition of these hydrophilic polymers in the lipid matrix increased the amount of theophylline released thanks to the swelling of the hydrophilic polymer and the creation of a porous network into the inert lipid matrix. The grade and the quantity of Lutrol could modulate the extent of drug release. Theophylline was released mainly by the matrix erosion but also by diffusion through the pores as suggested by the Peppas' model. Moreover, the addition of Lutrol enhanced the stability during storage. The theophylline release was quite steady after 6 months in different conditions (temperature and humidity). Thus, the mixture of glyceryl palmitostearate and poloxamers is an approach with many advantages for the development of controlled-release formulations by capsule molding.

Preparation and evaluation of a melt pelletised paracetamol/stearic acid sustained release delivery system

The potential of a sustained release formulation for paracetamol produced by melt pelletisation was investigated. The chosen formulation was based on the combination of stearic acid as a melting binder and anhydrous lactose as a filler. After determination of the size distribution, the pellet characterisation included scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), specific surface area and true density determination. Hence, the in vitro release from every single size fraction (2000, 1250, 800, 630, <630 microm) was evaluated and the release mechanism was analysed with the help of an appropriate mathematical model. The results of drug content and superficial atomic composition were found to be constant in all pellets size fractions, attesting the ability of melt pelletisation in a high shear mixer to form a product with homogeneous composition. The mathematical model is built on the hypotheses that drug diffusion and solid drug dissolution in the release environment are the key phenomena affecting drug release kinetics. Smaller classes apart (particles are not perfectly spherical), the comparison between model best fitting and experimental data indicated the reasonability of these hypotheses. Moreover, model reliability is proved by its ability of predicting drug release from a known mixture of the above mentioned particles classes.