Method development and validation for the HPLC potency assay of troglitazone tablets

Investigating the properties of subcritical water extraction with pharmaceutical tablets

The properties of subcritical water extraction (SWE) in the sample preparation of pharmaceutical tablets were investigated. Tablets comprised of microcrystalline cellulose excipients broke apart up to 80 times faster in subcritical water than they did in room temperature water, while those containing starch readily broke apart in either. Tablets containing starch were also observed to gelatinize or “paste” over several SWE conditions, impeding subsequent filtration and analysis. This effect was avoidable, however, since it was demonstrated to disappear with increases in extraction time and temperature or decreases in sample size. Using SWE, two common over-the-counter pharmaceuticals were extracted under optimized conditions from tablets comprised of either microcrystalline cellulose or starch excipients. Analyte recoveries of 95% or more were obtained at 150 °C for vitamin C (ascorbic acid) tablets in as little as 8 min for the extraction of a whole intact tablet, 6 min for two half tablets, and 5 min for a ground tablet. By comparison, this occurred at 250 °C in just 2 min for an intact slice of an acetaminophen tablet. Reproducibility was generally quite good with these trials producing RSD values of less than 2%. The results indicate that SWE can be a potentially viable and efficient method for the sample preparation of whole, sliced, or ground pharmaceutical tablets, and further exploration of this approach is promising.

Determination of troglitazone stereoisomers in rat plasma using semi-micro HPLC with electrochemical detection

A highly sensitive determination method for troglitazone stereoisomers was developed by high-performance liquid chromatography with electrochemical detection (HPLC-ECD). The oxidation behavior of troglitazone was investigated for the application of ECD by measuring the cyclic voltammogram. The separation was performed on a semi-micro chiral column (Chiralcel OJ-RH) using a mobile phase consisting of methanol-acetic acid (1000:1, v/v) containing 50mM LiClO4 at a flow rate of 20 microl/min. The peak areas of the stereoisomers separated from 0.1 to 50 ng/ml of troglitazone had good linearity with correlation coefficients of >0.999, and had similar response. The limit of detection was 1.3 fmol (signal-to-noise ratio of 3). This method was applied to the determination of troglitazone stereoisomers in rat plasma. The levels of troglitazone stereoisomers in rat plasma could be monitored until 24h after the oral administration.

Direct chiral separation of troglitazone stereoisomers using reversed-phase high-performance liquid chromatography

A simple HPLC method for the direct chiral separation of troglitazone stereoisomers was developed. The separation was performed on a reversed-phase cellulose-derivertized chiral column (Chiralcel OJ-R) using a mobile phase consisting of methanol-acetic acid (1000:1, v/v) at a flow rate of 0.5 ml/min. The peak areas of stereoisomers separated from 0.13 to 0.75 mg/ml of troglitazone had good linearity, with correlation coefficients > 0.999 in the reversed-phase mode. The repeatability of the ratios of stereoisomers isolated from 0.5 mg/ml of troglitazone had a relative standard deviation of 0.1-0.2%. The relative sensitivities of the four isomers at UV 285 nm were similar, as each response factor was within the range of 0.99-1.01. Troglitazone racemized at the chiral center of the thiazolidine ring in methanol solution, but was found to be stable for 24 h in methanol-acetic acid (1000:1, v/v). This method was applied to the stereoisomeric analysis of troglitazone in pharmaceutical formulations and used to evaluate the constancy of the stereoisomer ratio in the manufacturing process and stability testing.

Fast sample preparation for analysis of tablets and capsules: the ball-mill extraction method

A new ball-mill extraction method for solid dosage forms was developed. It was used for tablets, and compared with a conventional (powdering and sonication) method applied in pharmaceutical analysis of solid dosage forms. The ball-mill sample preparation procedure is both quantitative and fast. No powdering, weighing and sonication steps are needed in the sample preparation. The complete procedure takes 2 min (milling and extraction) and 5 min (centrifugation), respectively, much less than the conventional method in which sample preparation takes approximately 45-90 min. The samples are centrifuged in the mill vial, which saves time and avoids evaporation of solvent. Stainless steel extraction vials with different diameters were fabricated to enable the use of various extraction volumes. The extraction recovery was tested using various types of tablets (small, large and extended release tablets) with active compounds at low and higher concentrations, recoveries were comparable with the conventional method. The relative small investment and simplicity of the method makes it excellently suited for use in various pharmaceutical (development and quality assurance) laboratories.