The shear-induced destabilization of oil-in-water emulsions using caseinate as emulsifier

Shear-induced coalescence of oil-in-water Pickering emulsions

This work reports on coalescence in oil-in-water Pickering emulsions subjected to simple shear flow. The emulsions were stabilized by silanized fumed silica particles forming layers a few hundred nanometers thick around drops that are tens of micrometers in size. The drop size and particle concentration in the emulsions were fixed, while the salt concentration was varied to adjust the colloidal interactions between the drops and particles. At rest the oil drops do not coalesce. The susceptibility of the drops to orthokinetic coalescence was found to depend on the extent of particle flocculation in the attached particle layer. The evolution of the drop size with time and shear rate was consistent with phenomenological models used to describe the behavior of emulsions under shear.

Physicochemical behavior of oil-in-water emulsions: influence of milk protein mixtures, glycerol ester mixtures and fat characteristics

Different emulsions based on two protein mixtures (skim milk powder (SMP) and functional dairy proteins (FDP)), two mono-di-glyceride mixtures (MDG) (saturated and partially unsaturated), three fats (hydrogenated and refined coconut oils and refined palm oil) were studied to investigate the interactions occurring between the oil phase, low molecular weight emulsifiers and proteins. Immediately following the emulsification process, high diameters of fat globules were obtained in FDP-based systems, relevant of an aggregation phenomenon. At this stage, the fat globule size characteristics were dependent on the emulsifier and fat types present in the formulation. In contrast, SMP-based emulsions were characterized by low proportions of aggregated particles regardless the formulations. Ageing (24 h at 4 degrees C) promoted disaggregation in FDP formulations, while SMP emulsions were well stabilized. Just after the homogenization step, less proteins were required to stabilize the globule interface in FDP systems as compared to SMP ones. Only with SMP, the amount of protein load at the fat globule surface was influenced by the oil nature and/or by the emulsifier type. A competitive adsorption of caseins, over whey proteins, was demonstrated in the case of FDP. The ageing period promoted a displacement of the proteins adsorbed at the oil droplet interface, suggesting a disruption of the interfacial protein interactions. This disruption was more marked with SMP than with FDP and, in both cases, was more or less influenced by the emulsifier and oil phase natures. The variations of the viscosity and rheological parameters (elastic and viscous moduli) were not dependent on one specific component of the formulation.

Milk protein interfacial layers and the relationship to emulsion stability and rheology

The properties of milk protein-stabilised, oil-in-water emulsions are determined by the structure and surface rheology of the adsorbed layer at the oil-water interface. Analysis of the segment density profiles normal to the surface show differences in the structure between adsorbed layers of disordered casein and globular whey protein. Systematic studies of stability and rheology of model oil-in-water emulsion systems made with milk proteins as sole emulsifiers give insight into the relation between adsorbed layer properties and bulk emulsion stability. Of particular importance are effects of pH, temperature, calcium ions and protein content. Colloidal interactions between adsorbed layers on different surfaces can be inferred from an analysis of dynamic collisions of protein-coated emulsion droplets in shear flow using the colloidal particle scattering technique. The role of competitive adsorption on emulsion properties can be derived from experiments on systems containing mixtures of milk proteins and small-molecule surfactants. Shear-induced destabilisation is especially influenced by the presence of fat crystals in the emulsion droplets. Aggregated gel network properties are dependent on the balance of weak and strong interparticle interactions. In heat-set whey protein emulsion gels, the rheological behaviour is especially sensitive to surfactant type and concentration. Rearrangements of transient caseinate-based emulsion gels can have a profound influence on the quiesent stability behaviour. Computer simulation provides a general link between particle interactions, microstructure and rheological properties.

Orthokinetic flocculation of caseinate-stabilized emulsions: influence of calcium concentration, shear rate, and protein content

Calcium-induced flocculation of caseinate-stabilized soybean oil-in-water emulsions in conditions of Couette flow was studied. A concentrated emulsion (20% oil, 0.5-2.0% sodium caseinate in 20 mM imidazole, pH 7) was diluted 20 times in buffer containing concentrations of CaCl(2) between 9 and 17 mM and sheared at rates between 335 and 1340 s(-)(1). The average particle size (d(43)), measured by integrated light scattering, increased in a sigmoidal manner with shearing time. An increased shear rate resulted in an increased flocculation rate, because of the increased number of collisions between particles, but a decreased value of the maximum d(43), because higher shear rates increasingly disrupted the flocs. The flocculation rate was increased by increasing the calcium concentration, indicating an increased collision efficiency. The orthokinetic stability of the emulsions was increased with increased protein content, and it is postulated that the increased surface coverage and hydrodynamic thickness of the adsorbed protein layer increased steric repulsion between droplets, so that higher calcium concentrations were necessary to induce sufficient conformational change of the proteins to allow flocculation. At high caseinate concentrations, calcium may also induce precipitation of unadsorbed caseins from the serum to the oil-water interface, thereby increasing steric repulsion and hence increasing orthokinetic stability.