Chemical vapour deposition — a new approach to reactive surface defects of uniform geometry on high surface area magnesium oxide

Excess soluble alkalis to prepare highly efficient MgO with relative low surface oxygen content applied in DMC synthesis

The activities of various MgO catalysts, which were prepared from different methods such as hydration synthesis, thermal decomposition, combustion, sol–gel and co-precipitation, were conducted in dimethyl carbonate (DMC) synthesis via transesterification of ethylene carbonate with methanol. MgO-P-Na₂CO₃-3.14 synthesized by the excess Na₂CO₃ precipitation compared the best catalytic activity and stability, which could be reused for seven times without obvious deactivation. The DMC yield was as high as 69.97% at 68 °C. The transesterification reaction could be separated into two steps, and the samples obtained by NaOH precipitant exhibited better ring-opening capability, while the catalysts acquired by Na₂CO₃ precipitant displayed superior transesterification ability. The structure-performance relationship was evaluated by multiple characterization methods. The results indicated that the as-synthesized catalyst derived from dried precursors with more crystalline magnesium carbonate was favorable for the promotion of DMC yield, and MgO-P-Na₂CO₃-3.14 with more Mg-O pairs, which were the active center for the transesterification of 2-hydroxyethyl methyl carbonate (HEMC) intermediate with methanol, resulted in more moderately basic sites left that was in accordance with the DMC yield variation. MgO-P-Na₂CO₃-3.14 with greater BET surface area and mesopore volume, relative low surface oxygen content and larger moderately basic sites amount compared the excellent activity in DMC synthesis.

Thin water films and particle morphology evolution in nanocrystalline MgO

A key question in the field of ceramics and catalysis is how and to what extent residual water in the reactive environment of a metal oxide particle powder affects particle coarsening and morphology. With X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM), we investigated annealing-induced morphology changes on powders of MgO nanocubes in different gaseous H2O environments. The use of such a model system for particle powders enabled us to describe how adsorbed water that originates from short exposure to air determines the evolution of MgO grain size, morphology, and microstructure. While cubic nanoparticles with a predominant abundance of (100) surface planes retain their shape after annealing to T = 1173 K under continuous pumping with a base pressure of water p(H2O) = 10-5 mbar, higher water partial pressures promote mass transport on the surfaces and across interfaces of such particle systems. This leads to substantial growth and intergrowth of particles and simultaneously favors the formation of step edges and shallow protrusions on terraces. The mass transfer is promoted by thin films of water providing a two-dimensional solvent for Mg2+ ion hydration. In addition, we obtained direct evidence for hydroxylation-induced stabilization of (110) faces and step edges of the grain surfaces.

Porphyrin Metalation at the MgO Nanocube/Toluene Interface

Molecular insights into porphyrin adsorption on nanostructured metal oxide surfaces and associated ion exchange reactions are key to the development of functional hybrids for energy conversion, sensing, and light emission devices. Here we investigated the adsorption of tetraphenyl-porphyrin (2HTPP) from toluene solution on two types of MgO powder. We compare MgO nanocubes with an average size d < 10 nm and MgO cubes with 10 nm ≤ d ≤ 1000 nm. Using molecular spectroscopy techniques such as UV/vis transmission and diffuse reflectance (DR), photoluminescence (PL), and diffuse reflectance infrared Fourier-transform (DRIFT) spectroscopy in combination with structural characterization techniques (powder X-ray diffraction and transmission electron microscopy, TEM), we identified a new room temperature metalation reaction that converts 2HTPP into magnesium tetraphenyl-porphyrin (MgTPP). Mg(2+) uptake from the MgO nanocube surfaces and the concomitant protonation of the oxide surface level off at a concentration that corresponds to roughly one monolayer equivalent adsorbed on the MgO nanocubes. Larger MgO cubes, in contrast, show suppressed exchange, and only traces of MgTPP can be detected by photoluminescence.

Preparation and catalytic behavior of biomorphic calcium oxide/carbon solid base materials

Shaped CaO/carbon catalysts prepared via an in situ transformation exhibit high activities and can be regenerated by steam or CO₂ treatment.

O2 adsorption dependent photoluminescence emission from metal oxide nanoparticles

Optical properties of metal oxide nanoparticles are subject to synthesis related defects and adsorbates.

Optical properties of nanocrystal interfaces in compressed MgO nanopowders

The optical properties and charge trapping phenomena observed on oxide nanocrystal ensembles can be strongly influenced by the presence of nanocrystal interfaces. MgO powders represent a convenient system to study these effects due to the well-defined shape and controllable size distributions of MgO nanocrystals. The spectroscopic properties of nanocrystal interfaces are investigated by monitoring the dependence of absorption characteristics on the concentration of the interfaces in the nanopowders. The presence of interfaces is found to affect the absorption spectra of nanopowders more significantly than changing the size of the constituent nanocrystals and, thus, leading to the variation of the relative abundance of light-absorbing surface structures. We find a strong absorption band in the 4.0-5.5 eV energy range, which was previously attributed to surface features of individual nanocrystals, such as corners and edges. These findings are supported by complementary first-principles calculations. The possibility to directly address such interfaces by tuning the energy of excitation may provide new means for functionalization and chemical activation of nanostructures and can help improve performance and reliability for many nanopowder applications.

BaO clusters on MgO nanocubes: a quantitative analysis of optical-powder properties

Uniformly sized and shaped nanoparticles are well suited for the quantitative characterization of optical-powder properties. For the first time, quantum yields related to photoluminescence emissions that originate from the photoexcitation of MgO nanocube corners and edges are measured. In addition, the surfaces of these nanoparticles are doped with submonolayer barium, which oxidizes during adsorption onto the MgO nanocrystal surfaces and transforms in O(2) atmosphere into BaO. UV-Vis diffuse reflectance and photoluminescence spectroscopy is employed to explore whether 10(-3) monolayer equivalents of these dopants affect the MgO specific optical properties. Surface-admixed BaO produces additional absorption and photoluminescence emission features but does not significantly affect those specific to MgO nanocubes. On this basis the number of optically active sites that can be sampled inside a powder of alkaline earth oxide nanoparticles using a standard spectrometer system is estimated.

Optical surface properties and morphology of MgO and CaO nanocrystals

Optical absorption and photoluminescence emission properties of dehydroxylated MgO and CaO nanocrystals are discussed with respect to particle morphology and size. On MgO nanocubes with pronounced corner and edge features two emission bands at 3.4 and 3.3 eV result from the excitation of 4-coordinated surface O(4C)(2-) anions in edges at 5.4 eV and of regular oxygen-terminated corners at 4.6 eV, respectively. Morphologically ill-defined CaO particles are a factor of 5 larger, do not display regular corner features, and show only one photoluminescence emission band at 3.0 eV. The associated excitation spectrum indicates electronic excitations above the energy required to excite regular oxygen-terminated CaO corners. It is concluded that in the case of morphologically well-defined MgO nanocubes variations in the next coordination of oxygen-terminated corners can effectively be probed by photoluminescence spectroscopy and thus allows for discrimination between 3-coordinated surface O(2-) in regular corner sites and kinks.

Effect of Protons on the Optical Properties of Oxide Nanostructures

Site-specific functionalization of oxide nanostructures gives rise to novel optical and chemical surface properties. In addition, it can provide deeper insights into the electronic surface structure of the associated materials. We applied chemisorption of molecular hydrogen, induced by ultraviolet (UV) light, followed by vacuum annealing to MgO nanocubes to selectively decorate three-coordinated oxygen ions (oxygen corner sites, for simplicity) with protons. Fully dehydroxylated nanocubes exhibit 3.2 +/- 0.1 eV photoluminescence induced by 4.6 eV light, where both emission and absorption are associated with three-coordinated oxygen sites. We find that partially hydroxylated nanocubes show an additional photoluminescence feature at 2.9 +/- 0.1 eV. Interestingly, the excitation spectra of the 2.9 and 3.2 eV emission bands, associated with protonated and nonprotonated oxygen corner sites, respectively, nearly coincide and show well-pronounced maxima at 4.6 eV in spite of a significant difference in their local atomic and electronic structures. These observations are explained with the help of ab initio calculations, which reveal that (i) the absorption band at 4.6 eV involves four-coordinated O and Mg ions in the immediate vicinity of the corner sites and (ii) protonation of the three-coordinated oxygen ions eliminates the optical transitions associated with them and strongly red-shifts other optical transitions associated with neighboring atoms. These results demonstrate that the optical absorption bands assigned to topological surface defects are not simply determined by the ions of lowest coordination number but involve contributions due to the neighboring atoms of higher coordination. Thus, we suggest that the absorption band at 4.6 eV should not be regarded as merely a signature of the three-coordinated O2- ions but ought to be assigned to corners as multiatomic topological features. Our results also suggest that optical absorption signatures of protonated and nonprotonated sites of oxide surfaces can be remarkably similar.

Inside Powders: A Theoretical Model of Interfaces between MgO Nanocrystallites

The electron- and hole-trapping and optical properties of a wide variety of interfaces between MgO nanocrystallites are investigated for the first time using a quantum-mechanical embedded-cluster method and time-dependent density functional theory. We conclude that delocalized holes can be transiently trapped at a large number of places within a powder. However, it is more energetically favorable for holes to trap on low-coordinated anions on the nanocrystallite surface, forming O- species. Electrons are trapped at few interfaces but are readily trapped by surface kink and corner sites. Contrary to common perception, our calculations of optical absorption spectra indicate that a variety of features buried within a powder can be exited with photon energies less than 5 eV, usually used to selectively excite low-coordinated surface sites.

Revisiting Acido-basicity of the MgO Surface by Periodic Density Functional Theory Calculations: Role of Surface Topology and Ion Coordination on Water Dissociation

Low-coordinated (LC) ions at the MgO surface (noted Mg2+LC and O2-LC with L = 1-5), located on monatomic and diatomic steps, corners, step divacancies, and kinks, have been modeled thanks to periodic density functional theory (DFT) calculations (VASP). Ions of lowest coordination induce the strongest surface geometry relaxation and the highest surface energies. The hydration energies of these sites and thermodynamic stabilities of the resulting surfaces were studied. The factors controlling the interaction strength between water and the surface are the possibility for the hydroxyl group to adopt a bridging geometry between two Mg2+ cations in concave areas of the surface, such as the bottom of the monatomic step, and at second order the surface atomic coordination, and especially the presence of three-coordinated ions. The Lewis basicity and acidity of O2-LC and Mg2+LC, respectively, increase as their coordination number decreases, which implies the same trend for the Brønsted basicity of the Mg2+-O2- pair toward water. However, this trend can be changed if pairs leading to the formation of bridging OH groups are involved, typically on monatomic steps or in step divacancies where O2C-H and O3C-H are obtained, respectively, instead of the expected O1C-H. Thanks to thermodynamic calculations, the state of the surface as a function of temperature can be determined at a given pressure, unraveling the roles of surface topology and ions coordination.

Adsorption of Functionalized Benzoic Acids on MgSO4⋅H2O (100)

Using a combination of ab initio and semiempirical methods, adsorption problems on surfaces with large unit cells and low symmetry can still be studied. Here, a hybrid approach of density functional theory (DFT) and Hartree-Fock (HF) was used. As an example, we determined the geometry and the electronic properties of benzoic acid (BA), salicylic acid (SA) and para-salicylic acid (p-SA) adsorbed on MgSO(4).H(2)O (100), which are used as conditioner molecules for the electrostatic separation of minerals. Contrary to general expectations, these molecules are chemisorbed, with binding energies around 1.9 eV, forming bonds through the carboxylic O atom of the COOH groups in a nonplanar geometry, although the surface is a stoichiometric wide-band-gap insulator and the molecules stay intact. In contrast, a planar adsorption geometry turned out to be nonbonding. Bonding takes place by means of surface-molecule resonances due to the overlap of the valence band with molecular orbitals, assisted by a small charge-transfer molecule to the surface of around 0.15e. These combined interactions cause an intramolecular twist between the COOH group and the benzene ring.

Kinetic Model of Energy Transfer Processes Between Low-Coordinated Ions on MgO by Photoluminescence Decay Measurements

Photoluminescence decay studies of emitting species on MgO nanocubes at room temperature provide evidence of three surface species characterized by an excitation and emission wavelength couple {lambda(exc);lambda(em)}. Species A corresponds to {lambda(exc)=240 nm; lambda(em)=380 nm}, whereas the couple {lambda(exc)=280 nm; lambda(em)=470 nm} is assigned to two species: B and B', the former is involved in energy transfer from excited state A* and the latter in direct emission from excited state B'*. A simple model for energy transfer from species A* to B is proposed. The numerical resolution of equations corresponding to this model is in good agreement with experimental data. This method quantifies the kinetics of intrinsic emission and energy transfer processes. Lifetime values indicate that phosphorescence is taking place, and species A, B and B' are identified as edge O(2-) (4 C), corner O(2-) (3 C) and kink O(2-) (3 C) oxide ions respectively.

Charge Trapping and Photoadsorption of O2 on Dehydroxylated TiO2 Nanocrystals—An Electron Paramagnetic Resonance Study

The interaction of photogenerated charges with molecular oxygen was investigated on TiO2 nanocrystals by means of paramagnetic resonance (EPR) spectroscopy. Compared to photoactivation experiments in vacuum at P < 10(-6) mbar and T = 140 K, the presence of O2 enhances the concentration of persistently trapped electron and hole centres--by a factor of ten--due to the formation of adsorbed O2- species. The photoadsorption of oxygen was also tracked quantitatively by pressure measurements, and the number of trapped charges, hole centres and O2- was found to correspond to ten electron-hole pairs per TiO2 nanocrystal. Conversely, in experiments at P < 10(-6) mbar with one trapped electron-hole pair per particle, charge separation is not persistent and completely reversible with respect to temperature. Heating to 298 K causes the total annihilation of photogenerated and trapped charges.

Novel optical surface properties of Ca2+ -doped MgO nanocrystals

Surface doping of oxide nanoparticles is important in fields ranging from heterogeneous catalysis to optoelectronics. Here, we report the solvent-free synthesis of mixed calcium-magnesium oxide nanocrystals in the size range between 5 and 40 nm. Although CaMgO mixtures are thermodynamically forbidden on a macroscopic scale, Calcium ions can be distributed homogeneously in MgO using chemical vapor deposition (CVD) as a nonequilibrium technique. Subsequent thermal activation leads to calcium ion segregation into the nanocrystal surface which, in addition to the synthesis parameters, provides efficient means for manipulating the optical surface properties of insulating oxide nanocrystals. A novel material with unexpected photonic behavior, such as enhanced photoluminescence emission which is also red-shifted with respect to those of CaO and MgO, was found.

Chemistry at corners and edges: Generation and adsorption of H atoms on the surface of MgO nanocubes

We used UV light to generate site-selective O- hole centers at three-coordinated corner oxygen sites on MgO nanocubes. These highly reactive O- radicals split H2 homolytically and, in the course of this reaction, become hydroxylated and produce hydrogen atoms. The hydrogen atoms adsorb predominantly at cube edges and dissociate into surface-trapped electrons and protons. We propose that the experimentally observed (H+)(e-) centers are formed adjacent to the hydroxyl groups generated in the homolytic splitting process and can be defined as (H+)3C...(e-)(H+)NC centers where 3C and NC refer to the coordination numbers of the corresponding hydroxylated oxygen sites. Our ab initio embedded cluster calculations reveal that the electronic properties of (H+)3C...(e-)(H+)4C centers situated along MgO nanocube edges are consistent with both the electron-paramagnetic-resonance signal parameters and the reported optical-absorption properties. The transformation of corner O- centers into the (H+)3C...(e-)(H+)NC-type centers prevents their recombination with electronic surface centers and, hence, significantly alters the electronic structure of MgO nanocubes by introducing shallow electron traps.

Properties of Ternary Insulating Systems: The Electronic Structure of MgSO4·H2O

Structural and electronic properties of (100)-oriented MgSO(4) and MgSO(4).H(2)O surfaces and the adsorption of water on the latter were investigated theoretically with a combination of ab initio and semiempirical methods. Ab initio electronic structure calculations were based on a density functional theory (DFT)-Hartree-Fock (HF) hybrid approach. The semiempirical method MSINDO was used for the determination of the local adsorption geometry of the water molecule. With the hybrid method good agreement was obtained with the experimental band gap of 7.4 eV determined with electron energy loss spectroscopy of polycrystalline MgSO(4).H(2)O samples under ultrahigh vacuum conditions. The valence bands of the (100) surfaces of both MgSO(4) and MgSO(4).H(2)O are formed mainly by the O2p levels, whereas the S2p states contribute to the lower part of the conduction band. The preferred adsorption site of water at MgSO(4).H(2)O (100) is above a surface Mg atom. The water molecule is stabilized by two additional hydrogen bonds with surface atoms. Only small differences between the electronic structure of MgSO(4).H(2)O and MgSO(4) were observed. Also, the molecular adsorption of water on the MgSO(4).H(2)O surface leads to only small shifts of the electronic energy levels.

Physicochemical and in Situ Photoluminescence Study of the Reversible Transformation of Oxide Ions of Low Coordination into Hydroxyl Groups upon Interaction of Water and Methanol with MgO†,‖

The interaction of water and methanol with MgO samples with different distributions of oxide ions of low coordination has been investigated by physical techniques, particularly in situ photoluminescence. First, the three photoluminescence fingerprints of oxide ions vs their coordination number have been obtained for samples outgassed at 1273 K. By a pseudo quantitative approach, the relative distribution of the oxide ions of low coordination O(2-)LC (where LC = 3C, 4C, and 5C refer to tri-, tetra-, and pentacoordinated oxide ions, respectively) was determined and correlated with the shape and size of MgO particles determined by TEM and XRD. The photoluminescence of surfaces of MgO obtained after outgassing at increasing temperature or after interaction of water or methanol with a clean surface, i.e., obtained by outgassing at 1273 K, was then studied and evidenced three other photoluminescent species assigned to surface OH groups. The nature and mechanism of formation of the hydroxyls groups responsible for these new luminescent species are discussed in relation with their thermal stability and FTIR experiments.

Spectroscopic Properties of Trapped Electrons on the Surface of MgO Nanoparticles

To characterise electron-trapping sites on the surface of MgO nanoparticles, surface colour centres were generated using UV light in conjunction with selected hydrogen-based electron sources. Four different colour-centre species, including the characteristic (e-)(H+) or F(S)+(H) centre, were identified due to the distinct shape of the respective electron paramagnetic resonance (EPR) signals. The analysis of the EPR saturation behaviour down to microwave powers of 5 x 10(-3) mW reveals an enhanced spin-relaxation probability of the (e-)(H+) centre compared to all other F(S)+ centres that do not exhibit significant magnetic interactions with hydroxylic protons. Beside the dipolar magnetic interaction in the (e-)(H+) centre observed by EPR, the electronic interaction between the unpaired electron and the proton of a closely spaced OH group produces a redshift of the OH stretching band by about 70 to 170 cm(-1), as observed by infrared spectroscopy. EPR and IR spectroscopic data obtained after the selective address of individual reaction channels for surface colour-centre formation point to the fact that (e-)(H+) centres are formed by trapping electrons from H atoms. Consequently, the underlying surface defect does not belong to the sites of the MgO surface, which chemisorb hydrogen via a heterolytic splitting process.

Energy transfer on the MgO surface, monitored by UV-induced H2 chemisorption

Surface anions on edges (4-coordinated = 4C) and on corners (3-coordinated = 3C) of cubic MgO nanoparticles exhibit UV resonance absorptions around 5.5 and 4.6 eV, respectively. After monochromatic excitation of either site the electron paramagnetic resonance (EPR) spectrum exhibits exclusively signal components related to 3-coordinated O- radicals (O-(3C), electron hole centers), which are perfectly bleached by H(2) addition. The disappearance of the O-(3C) EPR signal components is paralleled by a depletion of the UV resonance absorption of the 3-coordinated O(2-) only and the appearance of one single band in the OH stretching region of the IR spectrum. Obviously the sites of UV excitation and subsequent UV induced surface reaction with H(2) are not the same. This may coherently be explained in terms of mobility of the exciton (O(2-)(4C)* or--after ionization--of the corresponding electron hole O-(4C) along the edge where it was created. Finally the mobile state is trapped at a corner site where the O(3C)H group is formed.