Recent developments in metal phosphide and sulfide electrocatalysts for oxygen evolution reaction

NiS2/NiS/Mn2O3 Nanofibers with Enhanced Oxygen Evolution Reaction Activity

The development of efficient and cost-effective electrocatalysts is crucial for achieving a green hydrogen economy through electrocatalytic water splitting. Herein, we report an excellent catalyst, one-dimensional NiS2/NiS/Mn2O3 nanofibers prepared by electrospinning, which exhibits outstanding electrochemical performance in an alkaline solution. We explored effective strategies to construct one-dimensional nanostructures and composite oxides to promote the electrocatalytic performance of transition metal dichalcogenides. At a current density of 20 mA cm-2, it requires an overpotential of 333 mV for OER. Furthermore, NiS2/NiS/Mn2O3 nanofibers maintain good durability even after 1000 cycles. The long-term electrochemical stability test of the catalyst NiS2/NiS/Mn2O3 was implemented at 20 mA cm-2 for 12 h. The potential remained at 99.52%. Therefore, this study demonstrates that NiS2/NiS/Mn2O3 can serve as a viable green hydrogen production electrocatalyst.

Transparent TiO2 nanotubes supporting silver sulfide for photoelectrochemical water splitting

Differences between photoelectrochemical and electrochemical activity were thoroughly investigated for the oxygen evolution reaction mediated by Ag2S deposited on two types of ordered titania substrates. Titanium dioxide nanotubes were fabricated by anodization of magnetron sputtered Ti films on ITO-coated glass substrates or directly from Ti foil. Further, Ag2S deposition on the nanotubes was carried out using successive ionic layer adsorption and reaction, known as SILAR, with 5, 25, and 45 cycles performed. Two types of nanotubes, one on transparent the other on non-transparent substrates were compared regarding their geometry, structure, optical, and electrochemical properties. It was demonstrated that the composite of Ag2S grown on transparent nanotubes exhibits higher catalytic activity compared to Ag2S grown on the nanotubes formed on Ti foil. The results showed that transparent nanotubes after modification with Ag2S by 25 SILAR cycles exhibit ca. 3 times higher photocurrent under visible light illumination than non-transparent ones treated with the same number of cycles. Furthermore, transparent nanotubes after 45 SILAR cycles of Ag2S exhibit enhanced activity towards oxygen evolution reaction with 9.3 mA cm-2 at 1.1 V vs. Ag/AgCl/0.1 M KCl which is six times higher than titania alone on Ti foil.

Biomass-Derived Catalytically Active Carbon Materials for the Air Electrode of Zn-Air Batteries

Given the growing environmental and energy problems, developing clean, renewable electrochemical energy storage devices is of great interest. Zn-air batteries (ZABs) have broad prospects in energy storage because of their high specific capacity and environmental friendliness. The unavailability of cheap air electrode materials and effective and stable oxygen electrocatalysts to catalyze air electrodes are main barriers to large-scale implementation of ZABs. Due to the abundant biomass resources, self-doped heteroatoms, and unique pore structure, biomass-derived catalytically active carbon materials (CACs) have great potential to prepare carbon-based catalysts and porous electrodes with excellent performance for ZABs. This paper reviews the research progress of biomass-derived CACs applied to ZABs air electrodes. Specifically, the principle of ZABs and the source and preparation method of biomass-derived CACs are introduced. To prepare efficient biomass-based oxygen electrocatalysts, heteroatom doping and metal modification were introduced to improve the efficiency and stability of carbon materials. Finally, the effects of electron transfer number and H2O2 yield in ORR on the performance of ZABs were evaluated. This review aims to deepen the understanding of the advantages and challenges of biomass-derived CACs in the air electrodes of ZABs, promote more comprehensive research on biomass resources, and accelerate the commercial application of ZABs.

Recent Progress on Copper-Based Bimetallic Heterojunction Catalysts for CO2 Electrocatalysis: Unlocking the Mystery of Product Selectivity

Copper-based bimetallic heterojunction catalysts facilitate the deep electrochemical reduction of CO2 (eCO2RR) to produce high-value-added organic compounds, which hold significant promise. Understanding the influence of copper interactions with other metals on the adsorption strength of various intermediates is crucial as it directly impacts the reaction selectivity. In this review, an overview of the formation mechanism of various catalytic products in eCO2RR is provided and highlight the uniqueness of copper-based catalysts. By considering the different metals' adsorption tendencies toward various reaction intermediates, metals are classified, including copper, into four categories. The significance and advantages of constructing bimetallic heterojunction catalysts are then discussed and delve into the research findings and current development status of different types of copper-based bimetallic heterojunction catalysts. Finally, insights are offered into the design strategies for future high-performance electrocatalysts, aiming to contribute to the development of eCO2RR to multi-carbon fuels with high selectivity.

Silver nanoparticle-decorated NiFe2O4/CuWO4 heterostructure electrocatalyst for oxygen evolution reactions

In this work, Ag nanoparticles decorated with NiFe2O4/CuWO4 heterostructure were synthesized using the step-wise precipitation method. The influence of varying Ag loading on the NiFe2O4/CuWO4 heterostructure and its electrochemical OER performance was extensively studied in 1 M KOH electrolyte. The obtained LSV profile was analyzed to determine the overpotential, Tafel slope, and onset potential. The heterostructure with an optimal Ag loading of 5 wt% required the least overpotential (1.60 V vs. RHE) for generating a current density of 10 mA cm-2 with a lower Tafel slope of 44.5 mV dec-1, indicating its faster OER kinetics. Furthermore, the composite remained stable over a period of 24 hours with a minimum rise in the overpotential after the stability test. The enhanced OER performance of the as-prepared catalyst can be attributed to the presence of multiple metallic elements in the Ag-loaded NiFe2O4/CuWO4 composite, which created a diverse array of oxygen-vacant sites with varying reactivity, enhancing the charge-transfer kinetics; and thus contributing to the overall efficiency of OER. Therefore, optimizing the Ag concentration and engineering a microstructure represents an encouraging strategy for developing cost-effective catalysts for next-generation energy-conversion applications.

Facile and scalable synthesis of Ni3S2/Fe3O4 nanoblocks as an efficient and stable electrocatalyst for oxygen evolution reaction

This study employed a one-step hydrothermal process to synthesize Ni3S2/Fe3O4 nanoblocks in situ on nickel foam (NF). The resulting Ni3S2/Fe3O4/NF catalyst demonstrates exceptional electrocatalytic activity for the oxygen evolution reaction (OER) and robust long-term stability. It achieves a low overpotential of only 220 mV for a current density of 10 mA cm-2 with a Tafel slope of 54.1 mV dec-1 and remains stable in 1.0 M KOH for 66 h. The binder-free self-supported three-dimensional nanoblocks enhance the reaction region and long-term stability. Electronic interactions between Fe3O4 and Ni3S2, coupled with heterogeneous interfaces, optimize the electronic structure, fostering the formation of highly reactive species. Density-functional theory (DFT) calculations confirm that Ni3S2/Fe3O4, with a heterogeneous interfacial structure, modulates the chemisorption of reaction intermediates on the catalyst surface, optimizing the Gibbs free energies (ΔG) of oxygen-containing intermediates. The synergistic effect between the two active materials within the heterogeneous structure enhances OER catalytic performance. This finding offers a valuable approach to designing efficient and stable OER electrocatalysts.

Enabling efficient ample-level oxygen evolution on nickel-iron Prussian blue analogue/hydroxide via hierarchical mass transfer channel construction

Enhancing double-phase mass transfer capability and reducing overpotential at high currents are critical in the oxygen evolution reaction (OER) catalyst design. In this work, nickel-iron layered double hydroxide (NiFe-LDH) loaded on nickel foam (NF) was used as a self-sacrificing template for subsequent growth of nickel-iron Prussian blue (NiFe-PBA) hollow nanocubes on its sheet arrays. The triple-scale porous structure is therefore in-situ constructed in the produced NiFe-PBA@LDH/NF catalyst, where NiFe-PBA nanocubes, NiFe-LDH sheets and NF skeletons provide pores at hundred-nanometers, microns and hundred-microns, respectively. Due to the successful construction of hierarchical mass transfer channels in the catalyst, the overpotential required to deliver 1000 mA cm-2 OER is only 396 mV, which is 80 mV lower than that of NiFe-LDH/NF with a double-scale porous structure, manifesting the importance of the appropriate mass transfer channels, promoting the potential application of the NiFe-PBA@LDH/NF catalyst in industrial-scale electrolysers.

In-situ construction defect-rich CuNiCoS4 /1T-MoS2 heterostructures as superior electrocatalysts for water splitting

Rational design and construction of bifunctional heterostructure electrocatalysts with high-conductivity and more active sites is imperative for water splitting. Herein, based on the tunable property of layered double hydroxide laminates cations, topological transformation technology and template confine method, a series of high-performance bifunctional catalysts composed of transition metal doping NiCo2S4 (MNiCoS4, M = Cu, Fe, Zn, Mn) and 1T-MoS2 were in-situ fabricated on nickel foam. In particular, CuNiCoS4/1T-MoS2 exhibits an ultralow overpotential of 163 mV at 50 mA cm-2 for oxygen evolution reaction (OER) and favorable hydrogen evolution reaction activity. The two-electrode system requires only 1.52 V to attain a current density of 10 mA cm-2. To the best of our knowledge, its OER electrocatalytic activity far exceed state-of-art catalysts reported. The outstanding performance of this series of catalysts can be attributed to two aspects. First, the highly conductive 1T-MoS2 can facilitate electron transfer, and second, the defect-rich heterostructure can effectively regulate the electronic structure of the active metal and expose abundant active sites. This work provides a valuable strategy for developing high activity electrocatalysts for efficient water splitting.

Ecotoxic effect in Allium cepa due to sphalerite weathering arising in calcareous conditions

The ecotoxic effect of Zn species arising from the weathering of the marmatite-like sphalerite ((Fe, Zn)S) in Allium cepa systems was herein evaluated in calcareous soils and connected with its sulfide oxidation mechanism to determine the chemical speciation responsible of this outcome. Mineralogical analyses (X-ray diffraction patterns, Raman spectroscopy, scanning electron microscopy and atomic force microscopy), chemical study of leachates (total Fe, Zn, Cd, oxidation-reduction potential, pH, sulfates and total alkalinity) and electrochemical assessments (chronoamperometry, chronopotentiometry, cyclic voltammetry, and electrochemical impedance spectroscopy) were carried out using (Fe, Zn)S samples to elucidate interfacial mechanisms simulating calcareous soil conditions. Results indicate the formation of polysulfides (Sn2-), elemental sulfur (S0), siderite (FeCO3)-like, hematite (Fe2O3)-like with sorbed CO32- species, gunningite (ZnSO4·H2O)-like phase and smithsonite (ZnCO3)-like compounds in altered surface under calcareous conditions. However, the generation of gunningite (ZnSO4·H2O)-like phase was predominant bulk-solution system. Quantification of damage rates ranges from 75 to 90% of bulb cells under non-carbonated conditions after 15-30 days, while 50-75% of damage level is determined under neutral-alkaline carbonated conditions. Damage ratios are 70.08 and 30.26 at the highest level, respectively. These findings revealed lower ecotoxic damage due to ZnCO3-like precipitation, indicating the effect of carbonates on Zn compounds during vegetable up-taking (exposure). Other environmental suggestions of the (Fe, Zn)S weathering and ecotoxic effects under calcareous soil conditions are discussed.

Enhancing anti-chlorine corrosion of Ni3S2 by Mo-doping for mimic seawater electrolysis

Designing highly active electrocatalysts that can resist chloride ion (Cl-) corrosion during seawater electrolysis is still a challenge. Here, Mo-doping is introduced to synchronously improve the electrocatalytic activity and anti-chlorine corrosion of Ni3S2 toward the efficient overall seawater splitting. With commercial nickel-molybdenum foam (NMF) as the reactive substrates, Mo-doped Ni3S2 columnar arrays (Mo-Ni3S2/NMF) are fabricated via a one-step hydrothermal process, which expose abundant active sites with the ameliorated surface electronic configurations toward the enhanced binding with *OH (* denotes an active site) but the weakened one with *Cl. As expected, they afford the excellent bi-functionality for both oxygen and hydrogen evolution reactions (OER and HER), with the remarkably improved anti-corrosion to Cl- at anode as compared to pristine Ni3S2. In alkaline mimic seawater (1.0 M NaOH + 0.5 M NaCl), Mo-Ni3S2/NMF requires 330 mV (for OER) and 209 mV (for HER) overpotentials at the current density of ±100 mA cm-2, and a low cell voltage of 1.52 V at 10 mA cm-2 for overall seawater splitting. This work highlights a feasible strategy to explore highly active and stable electrocatalysts for sustainable H2 production.

Highly Porous Carbon Flakes Derived from Cellulose and Nickel Phosphide Heterostructure towards Efficient Electrocatalysis of Oxygen Evolution Reaction

This study delves into the pressing challenges of climate change and the escalating carbon dioxide (CO2) emissions by exploring hydrogen technology as a sustainable alternative. In particular, there is focus on nickel phosphide-based electrocatalysts, known for their promising performance in hydrogen evolution reactions (HERs) and oxygen evolution reactions (OERs). Therefore, here we have designed a facile strategy to deliver highly porous carbon flakes derived from cellulose fibers via carbonization at 850 °C, yielding highly porous structures and outstanding specific surface area (SSAcel_carb_850_act = 3164 m2/g) after activation. As-fabricated carbon was utilized as a support for Ni12P5 with an optimized mass ratio. Electrochemical testing revealed that the composite of Ni12P5 and carbon flakes with a ratio of 100:1, respectively, exhibited the most favorable kinetics for the oxygen evolution reaction (OER). Importantly, the durability tests of this sample demonstrated the most stable behavior and lowest potential change under high current density among the studied samples, making it a promising candidate in practical applications. Moreover, the analysis of electrocatalysts after an OER does not show any changes, indicating that the sample does not undergo undesired intermediate reactions and that unwanted products are not released, explaining its stable behavior. This provides a straightforward approach for creating a cellulose-derived composite with enhanced electroactivity and durability.

One-Dimensional La0.2Sr0.8Cu0.4Co0.6O3-δ Nanostructures for Efficient Oxygen Evolution Reaction

Producing oxygen and hydrogen via the electrolysis of water has the advantages of a simple operation, high efficiency, and environmental friendliness, making it the most promising hydrogen production method. In this study, La0.2Sr0.8Cu0.4Co0.6O3-δ (LSCC) nanofibers were prepared by electrospinning to utilize non-noble perovskite oxides instead of noble metal catalysts for the oxygen evolution reaction, and the performance and electrochemical properties of LSCC nanofibers synthesized at different firing temperatures were evaluated. In an alkaline environment (pH = 14, 6 M KOH), the nanofibers calcined at 650 °C showed an overpotential of 209 mV at a current density of 10 mA cm-2 as well as good long-term stability. Therefore, the prepared LSCC-650 NF catalyst shows excellent potential for electrocatalytic oxygen evolution.

A Review of Transition Metal Boride, Carbide, Pnictide, and Chalcogenide Water Oxidation Electrocatalysts

Transition metal borides, carbides, pnictides, and chalcogenides (X-ides) have emerged as a class of materials for the oxygen evolution reaction (OER). Because of their high earth abundance, electrical conductivity, and OER performance, these electrocatalysts have the potential to enable the practical application of green energy conversion and storage. Under OER potentials, X-ide electrocatalysts demonstrate various degrees of oxidation resistance due to their differences in chemical composition, crystal structure, and morphology. Depending on their resistance to oxidation, these catalysts will fall into one of three post-OER electrocatalyst categories: fully oxidized oxide/(oxy)hydroxide material, partially oxidized core@shell structure, and unoxidized material. In the past ten years (from 2013 to 2022), over 890 peer-reviewed research papers have focused on X-ide OER electrocatalysts. Previous review papers have provided limited conclusions and have omitted the significance of "catalytically active sites/species/phases" in X-ide OER electrocatalysts. In this review, a comprehensive summary of (i) experimental parameters (e.g., substrates, electrocatalyst loading amounts, geometric overpotentials, Tafel slopes, etc.) and (ii) electrochemical stability tests and post-analyses in X-ide OER electrocatalyst publications from 2013 to 2022 is provided. Both mono and polyanion X-ides are discussed and classified with respect to their material transformation during the OER. Special analytical techniques employed to study X-ide reconstruction are also evaluated. Additionally, future challenges and questions yet to be answered are provided in each section. This review aims to provide researchers with a toolkit to approach X-ide OER electrocatalyst research and to showcase necessary avenues for future investigation.

Confinement Accelerates Water Oxidation Catalysis: Evidence from In Situ Studies

Basic insight into the structural evolution of electrocatalysts under operating conditions is of substantial importance for designing water oxidation catalysts. The first-row transition metal-based catalysts present state-of-the-art oxygen evolution reaction (OER) performance under alkaline conditions. Apparently, confinement has become an exciting strategy to boost the performance of these catalysts. The van der Waals (vdW) gaps of transition metal dichalcogenides are acknowledged to serve as a suitable platform to confine the first-row transition metal catalysts. This study focuses on confining Ni(OH)2 nanoparticle in the vdW gaps of 2D exfoliated SnS2 (Ex-SnS2 ) to accelerate water oxidation and to guarantee long term durability in alkaline solutions. The trends in oxidation states of Ni are probed during OER catalysis. The in situ studies confirm that the confined system produces a favorable environment for accelerated oxygen gas evolution, whereas the un-confined system proceeds with a relatively slower kinetics. The outstanding OER activity and excellent stability, with an overpotential of 300 mV at 100 mA cm-2 and Tafel slope as low as 93 mV dec-1 results from the confinement effect. This study sheds light on the OER mechanism of confined catalysis and opens up a way to develop efficient and low-cost electrocatalysts.

Surface Modification of a Lignin-Derived Carbon-Supported Co-Based Metal/Oxide Nanostructure for Alkaline Water Splitting

Exploring low-cost and eco-friendly bifunctional electrocatalysts of the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in alkaline electrolytes is still highly desired, and is crucial for water electrolysis and sustainable hydrogen generation. In this work, we report a facile pyrolysis-oxidation strategy to convert by-product lignin into bifunctional OER/HER electrocatalysts (Co/Co3O4-NPC-400) composed of Co/Co3O4 anchored on N-doped carbon with a surface of rich oxygen vacancies and oxygen-containing groups. The co-pyrolysis of lignin and NH4Cl can achieve a N-doped carbon matrix with a hierarchical pore structure, while the air-annealing process can induce the formation of oxygen-containing groups and oxygen vacancies. Owing to its surface properties, hierarchical pore structure and multiple active components, the constructed Co/Co3O4-NPC-400 possesses bifunctional catalytic activity and superior stability for OER/HER, especially for unexpected OER activity with a high current density of about 320 mA∙cm-2 at a potential of 1.8 V (vs. RHE). Water electrolysis using Co/Co3O4-NPC-400 as both the anode and the cathode needs a cell voltage of 1.95 and 2.5 V to attain about 10 and 400 mA∙cm-2 in 1 M KOH. This work not only provides a general strategy for the preparation of carbon-supported electrocatalysts for water splitting, but also opens up a new avenue for the utilization of lignin.

Research Progress of Hydrogen Production Technology and Related Catalysts by Electrolysis of Water

As a clean and renewable energy source for sustainable development, hydrogen energy has gained a lot of attention from the general public and researchers. Hydrogen production by electrolysis of water is the most important approach to producing hydrogen, and it is also the main way to realize carbon neutrality. In this paper, the main technologies of hydrogen production by electrolysis of water are discussed in detail; their characteristics, advantages, and disadvantages are analyzed; and the selection criteria and design criteria of catalysts are presented. The catalysts used in various hydrogen production technologies and their characteristics are emphatically expounded, aiming at optimizing the existing catalyst system and developing new high-performance, high-stability, and low-cost catalysts. Finally, the problems and solutions in the practical design of catalysts are discussed and explored.

Multicomponent Metal Oxide- and Metal Hydroxide-Based Electrocatalysts for Alkaline Water Splitting

Developing cost-effective, highly catalytic active, and stable electrocatalysts in alkaline electrolytes is important for the development of highly efficient anion-exchange membrane water electrolysis (AEMWE). To this end, metal oxides/hydroxides have attracted wide research interest for efficient electrocatalysts in water splitting owing to their abundance and tunable electronic properties. It is very challenging to achieve an efficient overall catalytic performance based on single metal oxide/hydroxide-based electrocatalysts due to low charge mobilities and limited stability. This review is mainly focused on the advanced strategies to synthesize the multicomponent metal oxide/hydroxide-based materials that include nanostructure engineering, heterointerface engineering, single-atom catalysts, and chemical modification. The state of the art of metal oxide/hydroxide-based heterostructures with various architectures is extensively discussed. Finally, this review provides the fundamental challenges and perspectives regarding the potential future direction of multicomponent metal oxide/hydroxide-based electrocatalysts.

Advanced Nanostructured Materials for Electrocatalysis in Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) batteries are considered as among the most promising electrochemical energy storage devices due to their high theoretical energy density and low cost. However, the inherently complex electrochemical mechanism in Li-S batteries leads to problems such as slow internal reaction kinetics and a severe shuttle effect, which seriously affect the practical application of batteries. Therefore, accelerating the internal electrochemical reactions of Li-S batteries is the key to realize their large-scale applications. This article reviews significant efforts to address the above problems, mainly the catalysis of electrochemical reactions by specific nanostructured materials. Through the rational design of homogeneous and heterogeneous catalysts (including but not limited to strategies such as single atoms, heterostructures, metal compounds, and small-molecule solvents), the chemical reactivity of Li-S batteries has been effectively improved. Here, the application of nanomaterials in the field of electrocatalysis for Li-S batteries is introduced in detail, and the advancement of nanostructures in Li-S batteries is emphasized.

Surface Design Strategy of Catalysts for Water Electrolysis

Hydrogen, a new energy carrier that can replace traditional fossil fuels, is seen as one of the most promising clean energy sources. The use of renewable electricity to drive hydrogen production has very broad prospects for addressing energy and environmental problems. Therefore, many researchers favor electrolytic water due to its green and low-cost advantages. The electrolytic water reaction comprises the oxygen evolution reaction (OER) and the hydrogen evolution reaction (HER). Understanding the OER and HER mechanisms in acidic and alkaline processes contributes to further studying the design of surface regulation of electrolytic water catalysts. The OER and HER catalysts are mainly reviewed for defects, doping, alloying, surface reconstruction, crystal surface structure, and heterostructures. Besides, recent catalysts for overall water splitting are also reviewed. Finally, this review paves the way to the rational design and synthesis of new materials for highly efficient electrocatalysis.

Nanostructured Metal Phosphide Based Catalysts for Electrochemical Water Splitting: A Review

Amongst various futuristic renewable energy sources, hydrogen fuel is deemed to be clean and sustainable. Electrochemical water splitting (EWS) is an advanced technology to produce pure hydrogen in a cost-efficient manner. The electrocatalytic hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) are the vital steps of EWS and have been at the forefront of research over the past decades. The low-cost nanostructured metal phosphide (MP)-based electrocatalysts exhibit unconventional physicochemical properties and offer very high turnover frequency (TOF), low over potential, high mass activity with improved efficiency, and long-term stability. Therefore, they are deemed to be potential electrocatalysts to meet practical challenges for supporting the future hydrogen economy. This review discusses the recent research progress in nanostructured MP-based catalysts with an emphasis given on in-depth understanding of catalytic activity and innovative synthetic strategies for MP-based catalysts through combined experimental (in situ/operando techniques) and theoretical investigations. Finally, the challenges, critical issues, and future outlook in the field of MP-based catalysts for water electrolysis are addressed.

Electrochemically Derived Crystalline CuO from Covellite CuS Nanoplates: A Multifunctional Anode Material

In the present era, electrochemical water splitting has been showcased as a reliable solution for alternative and sustainable energy development. The development of a cheap, albeit active, catalyst to split water at a substantial overpotential with long durability is a perdurable challenge. Moreover, understanding the nature of surface-active species under electrochemical conditions remains fundamentally important. A facile hydrothermal approach is herein adapted to prepare covellite (hexagonal) phase CuS nanoplates. In the covellite CuS lattice, copper is present in a mixed-valent state, supported by two different binding energy values (932.10 eV for Cu^I and 933.65 eV for Cu^II) found in X-ray photoelectron spectroscopy analysis, and adopted two different geometries, that is, trigonal planar preferably for Cu^I and tetrahedral preferably for Cu^II. The as-synthesized covellite CuS behaves as an efficient electro(pre)catalyst for alkaline water oxidation while deposited on a glassy carbon and nickel foam (NF) electrodes. Under cyclic voltammetry cycles, covellite CuS electrochemically and irreversibly oxidized to CuO, indicated by a redox feature at 1.2 V (vs the reversible hydrogen electrode) and an ex situ Raman study. Electrochemically activated covellite CuS to the CuO phase (termed as CuS_EA) behaves as a pure copper-based catalyst showing an overpotential (η) of only 349 (±5) mV at a current density of 20 mA cm^-2, and the TOF value obtained at η₃₄₉ (at 349 mV) is 1.1 × 10^-3 s^-1. A low R_ct of 5.90 Ω and a moderate Tafel slope of 82 mV dec^-1 confirm the fair activity of the CuS_EA catalyst compared to the CuS precatalyst, reference CuO, and other reported copper catalysts. Notably, the CuS_EA/NF anode can deliver a constant current of ca. 15 mA cm^-2 over a period of 10 h and even a high current density of 100 mA cm^-2 for 1 h. Post-oxygen evolution reaction (OER)-chronoamperometric characterization of the anode via several spectroscopic and microscopic tools firmly establishes the formation of crystalline CuO as the active material along with some amorphous Cu(OH)₂ via bulk reconstruction of the covellite CuS under electrochemical conditions. Given the promising OER activity, the CuS_EA/NF anode can be fabricated as a water electrolyzer, Pt(-)//(+)CuS_EA/NF, that delivers a j of 10 mA cm^-2 at a cell potential of 1.58 V. The same electrolyzer can further be used for electrochemical transformation of organic feedstocks like ethanol, furfural, and 5-hydroxymethylfurfural to their respective acids. The present study showcases that a highly active CuO/Cu(OH)₂ heterostructure can be constructed in situ on NF from the covellite CuS nanoplate, which is not only a superior pure copper-based electrocatalyst active for OER and overall water splitting but also for the electro-oxidation of industrial feedstocks.

Electrochemical incorporation of heteroatom into surface reconstruction induced Ni vacancy of NixO nanosheet for enhanced water oxidation

Surface reconstruction of non-oxide oxygen evolution reaction (OER) electrocatalysts has been intensively studied to improve their catalytic performances. However, further modification of the reconstructed active surfaces for better catalytic performances has not been reported. In this work, NiSe nanorods are prepared on nickel foam (NiSe@NF) as the pre-catalyst for electrochemical OER. It is revealed that non-stoichiometric NiO nanosheets with abundant Ni vacancies (Ni_xO) are formed on the surfaces of NiSe nanorods (Ni_xO/NiSe@NF) via in-situ electrochemical oxidation. Furthermore, the OER performances are obviously improved after heteroatom Fe is incorporated electrochemically into Ni_xO nanosheets ((FeNi)O/NiSe@NF). For OER to have a current density of 20 mA cm^-2 in 1 M KOH solution, the as-prepared (FeNi)O/NiSe@NF electrode only needs an overpotential of 268 mV. Density functional theory (DFT) calculations reveal that the formation of Ni vacancy can increase the free energy of *OH. More importantly, the incorporation of heteroatom Fe into Ni vacancy can significantly decrease the free energy of *O, which enables Fe-NiO to have the lowest theoretical overpotential for OER in this work. The present work provides a facile and universal strategy to modify the reconstructed active oxides' surfaces for higher electrocatalytic performances.

Cu2S Nanoflakes Decorated with NiS Nanoneedles for Enhanced Oxygen Evolution Activity

Metal sulfides are considered excellent materials for oxygen evolution reaction because of their excellent conductivity and high electrocatalytic activity. In this report, the NiS-Cu₂S composites were prepared on copper foam (NiS-Cu₂S-CF) using a facile synthetic strategy. The scanning electron microscopy results confirmed that the NiS nanoneedles were successfully grown on Cu₂S nanoflakes, greatly increasing the active sites. Particularly, the optimized 15% NiS-Cu₂S-CF composite demonstrated excellent oxygen evolution activity with a small overpotential of 308 mV@20 mA cm⁻², which is significantly smaller than that of noble metal-based electrocatalysts and other NiS-Cu₂S-CF composites. The enhanced oxygen evolution activity is attributed to the unique morphology that can provide ample active sites, rich ion-transfer pathways, and the synergistic effect between NiS and Cu₂S, which can boost the electron transfer rate.

Metal-Organic Frameworks Derived Electrocatalysts for Oxygen and Carbon Dioxide Reduction Reaction

The increasing demands of energy and environmental concerns have motivated researchers to cultivate renewable energy resources for replacing conventional fossil fuels. The modern energy conversion and storage devices required high efficient and stable electrocatalysts to fulfil the market demands. In previous years, we are witness for considerable developments of scientific attention in Metal-organic Frameworks (MOFs) and their derived nanomaterials in electrocatalysis. In current review article, we have discussed the progress of optimistic strategies and approaches for the manufacturing of MOF-derived functional materials and their presentation as electrocatalysts for significant energy related reactions. MOFs functioning as a self-sacrificing template bid different benefits for the preparation of metal nanostructures, metal oxides and carbon-abundant materials promoting through the porous structure, organic functionalities, abundance of metal sites and large surface area. Thorough study for the recent advancement in the MOF-derived materials, metal-coordinated N-doped carbons with single-atom active sites are emerging candidates for future commercial applications. However, there are some tasks that should be addressed, to attain improved, appreciative and controlled structural parameters for catalytic and chemical behavior.

A Superior and Stable Electrocatalytic Oxygen Evolution Reaction by One-Dimensional FeCoP Colloidal Nanostructures

Transition metal phosphides (TMPs) are expected to be excellent electrocatalysts for oxygen evolution reaction (OER) because of their high stability, highly conducting metalloid nature, highly abundant constituting elements, and the ability to act as a precatalyst due to in situ surface-formed oxy-hydroxide species. Herein, a "one-pot" colloidal approach has been used to develop a rod-shaped one-dimensional non-noble metal FeCoP electrocatalyst, which exhibits an excellent OER activity with an exceptionally high current density of 950 mA cm^-2, a turnover frequency value of 7.43 s^-1, and a low Tafel slope value of 54 mV dec^-1. The FeCoP electrocatalyst affords OER ultralow overpotentials of 230 and 260 mV at current densities of 50 and 100 mA cm^-2, respectively, in 1.0 M KOH, and demonstrates a superior catalytic stability of 10,000 cycles and durability up to 60 h at 50 mA cm^-2. An insight into the superior and stable electrocatalytic OER performance by the FeCoP nanorods is obtained by extensive X-ray photoelectron spectroscopy, X-ray diffraction, Raman and infrared spectroscopy, and cyclic voltammetry analyses for a mechanistic study. This reveals that a high number of electrocatalytically active sites enhance the oxygen evolution and kinetics by offering metal ion sites for utilitarian in situ surface formation and adsorption of *O, *OH, and *OOH reactive species for OER catalysis.

High catalytic performance of nano-flowered Mg-doped NiCo layered double hydroxides for the oxygen evolution reaction

Layered double hydroxides (LDHs) are one of the ideal functional materials for the oxygen evolution reaction (OER) because of their special configuration and good electrochemical activity.

Lithium-Sulfur Battery Cathode Design: Tailoring Metal-Based Nanostructures for Robust Polysulfide Adsorption and Catalytic Conversion

Lithium-sulfur (Li-S) batteries have a high specific energy capacity and density of 1675 mAh g^-1 and 2670 Wh kg^-1 , respectively, rendering them among the most promising successors for lithium-ion batteries. However, there are myriads of obstacles in the practical application and commercialization of Li-S batteries, including the low conductivity of sulfur and its discharge products (Li₂ S/Li₂ S₂ ), volume expansion of sulfur electrode, and the polysulfide shuttle effect. Hence, immense attention has been devoted to rectifying these issues, of which the application of metal-based compounds (i.e., transition metal, metal phosphides, sulfides, oxides, carbides, nitrides, phosphosulfides, MXenes, hydroxides, and metal-organic frameworks) as sulfur hosts is profiled as a fascinating strategy to hinder the polysulfide shuttle effect stemming from the polar-polar interactions between the metal compounds and polysulfides. This review encompasses the fundamental electrochemical principles of Li-S batteries and insights into the interactions between the metal-based compounds and the polysulfides, with emphasis on the intimate structure-activity relationship corroborated with theoretical calculations. Additionally, the integration of conductive carbon-based materials to ameliorate the existing adsorptive abilities of the metal-based compound is systematically discussed. Lastly, the challenges and prospects toward the smart design of catalysts for the future development of practical Li-S batteries are presented.

Atomic Cation-Vacancy Engineering of NiFe-Layered Double Hydroxides for Improved Activity and Stability towards the Oxygen Evolution Reaction

NiFe-layered double hydroxides (NiFe-LDH) are among the most active catalysts developed to date for the oxygen evolution reaction (OER) in alkaline media, though their long-term OER stability remains unsatisfactory. Herein, we reveal that the stability degradation of NiFe-LDH catalysts during alkaline OER results from a decreased number of active sites and undesirable phase segregation to form NiOOH and FeOOH, with metal dissolution underpinning both of these deactivation mechanisms. Further, we demonstrate that the introduction of cation-vacancies in the basal plane of NiFe LDH is an effective approach for achieving both high catalyst activity and stability during OER. The strengthened binding energy between the metals and oxygen in the LDH sheets, together with reduced lattice distortions, both realized by the rational introduction of cation vacancies, drastically mitigate metal dissolution from NiFe-LDH under high oxidation potentials, resulting in the improved long-term OER stability. In addition, the cation vacancies (especially M³⁺ vacancies) accelerate the evolution of surface γ-(NiFe)OOH phases, thereby boosting the OER activity. The present study highlights that tailoring atomic cation-vacancies is an important strategy for the development of active and stable OER electrocatalysts.

Structural and Interfacial Engineering of Ni2P/Fe3O4 Porous Nanosheet Arrays for Efficient Oxygen Evolution Reaction

Rational design of transition-metal phosphide (TMPs)-based electrocatalysts can effectively promote oxygen evolution reaction (OER). Herein, the novel efficient Ni₂P/Fe₃O₄ porous nanosheets arrays supported on Ni foam (Ni₂P/Fe₃O₄/NF) as alkaline OER catalysts were synthesized using structural and interfacial engineering. The three-dimensional (3D) porous hierarchical structure of Ni₂P/Fe₃O₄/NF provides abundant active sites for OER and facilitates the electrolyte diffusion of ions and O₂ liberation. Furthermore, the strong interfacial coupling and synergistic effect between Ni₂P and Fe₃O₄ modify the electronic structure, resulting in the enhanced intrinsic activity. Consequently, the optimized Ni₂P/Fe₃O₄/NF exhibits excellent OER performance with low overpotentials of 213 and 240 mV at 60 and 100 mA cm^-2 in 1.0 M KOH, respectively, better than the RuO₂/NF and most Ni/Fe-based OER catalysts. Impressively, it can maintain its catalytic activity for at least 20 h at 60 mA cm^-2. In addition, the relationship between the structure and performance is fully elucidated by the experimental characterizations, indicating that the metal oxyhydroxides in situ generated on the surface of catalysts are responsible for the high OER activity.

Electronic modulation and proton transfer by iron and borate co-doping for synergistically triggering the oxygen evolution reaction on a hollow NiO bipyramidal prism

Designing an Earth-abundant and inexpensive electrocatalyst to drive the oxygen evolution reaction (OER) for high-purity hydrogen production is of great importance. Herein, the cation (iron) and anion (borate) co-doping strategy was proposed to effectively trigger the OER performance on a low-cost NiO material. The optimal hollow Fe/B_i-NiO bipyramidal prism shows superior OER performance, and displays a low overpotential (261 mV) at 10 mA cm^-2, accompanied by a low Tafel slope (46 mV dec^-1), excellent intrinsic activity and robust stability. The overall alkaline water splitting using Fe/B_i-NiO/NF as an anode affords low cell voltages of 1.50 and 1.63 V at 10 and 100 mA cm^-2, and operates steadily at a high current density of 100 mA cm^-2 for 55 h without decay. The excellent electrocatalytic activity could be ascribed to the hollow structure to shorten the mass transfer pathway, the electronic modulation by Fe doping, the increased accessible electroactive sites created by oxygen vacancies through borate doping, and the formation of BO₃^3--OH^- to accelerate the deprotonation of OH_ads.

Hydrogen-etched CoS2 to produce a Co9S8@CoS2 heterostructure electrocatalyst for highly efficient oxygen evolution reaction

There is a pressing requirement for developing high-efficiency non-noble metal electrocatalysts in oxygen evolution reactions (OER), where transition metal sulfides are considered to be promising electrocatalysts for the OER in alkaline medium. Herein, we report the outstanding OER performance of Co9S8@CoS2 heterojunctions synthesized by hydrogen etched CoS2, where the optimized heterojunction shows a low η 50 of 396 mV and a small Tafel slope of 181.61 mV dec-1. The excellent electrocatalytic performance of this heterostructure is attributed to the interface electronic effect. Importantly, the post-stage characterization results indicate that the Co9S8@CoS2 heterostructure exhibits a dynamic reconfiguration during the OER with the formation of CoOOH in situ, and thus exhibits a superior electrocatalytic performance.

Metal-Organic Frameworks-Derived Self-Supported Carbon-Based Composites for Electrocatalytic Water Splitting

Electrocatalytic water splitting has been considered as a promising strategy for the sustainable evolution of hydrogen energy and storage of intermittent electric energy. Efficient catalysts for electrocatalytic water splitting are urgently demanded to decrease the overpotentials and promote the sluggish reaction kinetics. Carbon-based composites, including heteroatom-doped carbon materials, metals/alloys@carbon composites, metal compounds@carbon composites, and atomically dispersed metal sites@carbon composites have been widely used as the catalysts due to their fascinating properties. However, these electrocatalysts are almost powdery form, and should be cast on the current collector by using the polymeric binder, which would result in the unsatisfied electrocatalytic performance. In comparison, a self-supported electrode architecture is highly attractive. Recently, self-supported metal-organic frameworks (MOFs) constructed by coordination of metal centers and organic ligands have been considered as suitable templates/precursors to construct free-standing carbon-based composites grown on conductive substrate. MOFs-derived carbon-based composites have various merits, such as the well-aligned array architecture and evenly distributed active sites, and easy functionalization with other species, which make them suitable alternatives to non-noble metal-included electrocatalysts. In this review, we intend to show the research progresses by employment of MOFs as precursors to prepare self-supported carbon-based composites. Focusing on these MOFs-derived carbon-based nanomaterials, the latest advances in their controllable synthesis, composition regulation, electrocatalytic performances in hydrogen evolution reaction (HER), oxygen evolution reaction (OER), and overall water splitting (OWS) are presented. Finally, the challenges and perspectives are showed for the further developments of MOFs-derived self-supported carbon-based nanomaterials in electrocatalytic reactions.

Comprehensive Understandings into Complete Reconstruction of Precatalysts: Synthesis, Applications, and Characterizations

Reconstruction induced by external environment (such as applied voltage bias and test electrolytes) changes catalyst component and catalytic behaviors. Investigations of complete reconstruction in energy conversion recently receive intensive attention, which promote the targeted design of top-performance materials with maximum component utilization and good stability. However, the advantages of complete reconstruction, its design strategies, and extensive applications have not achieved the profound understandings and summaries it deserves. Here, this review systematically summarizes several important advances in complete reconstruction for the first time, which includes 1) fundamental understandings of complete reconstruction, the characteristics and advantages of completely reconstructed catalysts, and their design principles, 2) types of reconstruction-involved precatalysts for oxygen evolution reaction catalysis in wide pH solution, and origins of limited reconstruction degree as well as design strategies/principles toward complete reconstruction, 3) complete reconstruction for novel material synthesis and other electrocatalysis fields, and 4) advanced in situ/operando or multiangle/level characterization techniques to capture the dynamic reconstruction processes and real catalytic contributors. Finally, the existing major challenges and unexplored/unsolved issues on studying the reconstruction chemistry are summarized, and an outlook for the further development of complete reconstruction is briefly proposed. This review will arouse the attention on complete reconstruction materials and their applications in diverse fields.