A comparison of Al2O3 and SiO2 supported Ni-based catalysts in their performance for the dry reforming of methane

Enhancement of Ni-NiO-CeO2 Interaction on Ni-CeO2/Al2O3-MgO Catalyst by Ammonia Vapor Diffusion Impregnation for CO2 Reforming of CH4

Ni-based catalysts have been widely used for the CO2 reforming of methane (CRM) process, but deactivation is their main problem. This study created an alternative electronic Ni-NiO-CeO2 interaction on the surface of 5 wt% Ni-5 wt% CeO2/Al2O3-MgO (5Ni5Ce(xh)/MA) catalysts to enhance catalytic potential simultaneously with coke resistance for the CRM process. The Ni-NiO-CeO2 network was developed on Al2O3-MgO through layered double hydroxide synthesis via our ammonia vapor diffusion impregnation method. The physical properties of the fresh catalysts were analyzed employing FESEM, N2 physisorption, and XRD. The chemical properties on the catalyst surface were analyzed employing H2-TPR, XPS, H2-TPD, CO2-TPD, and O2-TPD. The CRM performances of reduced catalysts were evaluated at 600 °C under ambient pressure. Carbon deposits on spent catalysts were determined quantitatively and qualitatively by TPO, FESEM, and XRD. Compared to 5 wt% Ni-5 wt% CeO2/Al2O3-MgO prepared by the traditional impregnation method, the electronic interaction of the Ni-NiO-CeO2 network with the Al2O3-MgO support was constructed along the time of ammonia diffusion treatment. The electronic interaction in the Ni-NiO-CeO2 nanostructure of the treated catalyst develops surface hydroxyl sites with an efficient pathway of OH* and O* transfer that improves catalytic activities and coke oxidation.

Exploring the oxidation behavior of undiluted and diluted iron particles for energy storage: Mössbauer spectroscopic analysis and kinetic modeling

Iron is an abundant and non-toxic element that holds great potential as energy carrier for large-scale and long-term energy storage. While from a general viewpoint iron oxidation is well-known, the detailed kinetics of oxidation for micrometer sized particles are missing, but required to enable large-scale utilization for energy production. In this work, iron particles are subjected to temperature-programmed oxidation. By dilution with boron nitride a sintering of the particles is prevented enabling to follow single particle effects. The mass fractions of iron and its oxides are determined for different oxidation times using Mössbauer spectroscopy. On the basis of the extracted phase compositions obtained at different times and temperatures (600-700 °C), it can be concluded that also for particles the oxidation follows a parabolic rate law. The parabolic rate constants are determined in this transition region. Knowledge of the particle size distribution and its consideration in modeling the oxidation kinetics of iron powder has proven to be crucial.

Alumina-Magnesia-Supported Ni for Hydrogen Production via the Dry Reforming of Methane: A Cost-Effective Catalyst System

5Ni/MgO and 5Ni/γAl2O3 are pronounced in the line of cheap catalyst systems for the dry reforming of methane. However, the lower reducibility of 5Ni/MgO and the significant coke deposition over 5Ni/γAl2O3 limit their applicability as potential DRM catalysts. The mixing capacity of MgO and Al2O3 may overcome these limitations without increasing the catalyst cost. Herein, a 5Ni/xMg(100 - x)Al (x = 0, 20, 30, 60, 70, and 100 wt. %) catalyst system is prepared, investigated, and characterized with X-ray diffraction, surface area and porosity measurements, H2-temperature programmed reduction, UV-Vis-IR spectroscopy, Raman spectroscopy, thermogravimetry, and transmission electron microscopy. Upon the addition of 20 wt. % MgO into the Al2O3 support, 5Ni/20Mg80Al is expanded and carries both stable Ni sites (derived through the reduction of NiAl2O4) and a variety of CO2-interacting species. CH4 decomposition at Ni sites and the potential oxidation of carbon deposits by CO2-interacting species over 5Ni/20Mg80Al results in a higher 61% H2-yield (against ~55% H2-yield over 5Ni/γAl2O3) with an excellent carbon-resistant property. In the major magnesia support system, the 5Ni/60Mg40Al catalyst carries stable Ni sites derived from MgNiO2 and "strongly interacted NiO-species". The H2-yield over the 5Ni/60Mg40Al catalyst moves to 71%, even against a high coke deposition, indicating fine tuning between the carbon formation and diffusion rates. Ni dispersed over magnesia-alumina with weight ratios of 7/3 and 3/7 exhibit good resistance to coke. Weight ratios of 2/8 and 7/3 contain an adequate amount of reducible and CO2-interactive species responsible for producing over 60% of H2-yield. Weight ratio 6/4 has a proper coke diffusion mechanism in addition to achieving a maximum of 71% H2-yield.

Understanding Coke Deposition Vis-à-Vis DRM Activity over Magnesia-Alumina Supported Ni-Fe, Ni-Co, Ni-Ce, and Ni-Sr Catalysts

The catalytic conversion of CH4 and CO2 into H2-rich syngas is known as the dry reforming of methane (DRM). The dissociation of CH4 over active sites, coupled with the oxidation or polymerization of CH4-x (x = 1-4), plays a crucial role in determining in determining the DRM product yield and coke deposition. Herein, a series of bimetallic-supported catalysts are prepared by the dispersion of Ni-M (M = Ce, Co, Fe, and Sr) over 60 wt% MgO-40 wt% Al2O3 (60Mg40Al) support. Catalysts are tested for DRM and characterized with XRD, surface area and porosity, temperature-programmed reduction/desorption, UV-VIS-Raman spectroscopy, and thermogravimetry. 2.5Ni2.5Sr/60Mg40Al and 2.5Ni2.5Fe/60Mg40Al, and 2.5Ni2.5Ce/60Mg40Al and 2.5Ni2.5Co/60Mg40Al have similar CO2 interaction profiles. The 2.5Ni2.5Sr/60Mg40Al catalyst nurtures inert-type coke, whereas 2.5Ni2.5Fe/60Mg40Al accelerates the deposition of huge coke, which results in catalytic inferiority. The higher activity over 2.5Ni2.5Ce/60Mg40Al is due to the instant lattice oxygen-endowing capacity for oxidizing coke. Retaining a high DRM activity (54% H2-yield) up to 24 h even against a huge coke deposition (weight loss 46%) over 2.5Ni2.5Co/60Mg40Al is due to the timely diffusion of coke far from the active sites or the mounting of active sites over the carbon nanotube.

Gold and Ceria Modified NiAl Hydrotalcite Materials as Catalyst Precursors for Dry Reforming of Methane

Structured hydrotalcite NiAl-HT material with Ni/Al atomic ratio of 2.5 was prepared by co-precipitation of Ni and Al nitrate precursors and then modified by the addition of 1 wt% Ce and/or 3 wt% Au species. The obtained materials, after calcination at 600 °C, were characterized by XRD, XPS and TPR. Their catalytic performance was tested through dry reforming of methane (DRM) and by the temperature-programmed surface reaction of methane (TPSR-CH4). Thermal gravimetry analysis (TGA) of the spent catalysts was performed to determine the amount of carbon accumulated during the reaction. The effects of the addition of cerium as a support promoter and gold as nickel promoter and the sequential addition of cerium and gold on the structural properties and on the catalytic efficiency were investigated. Under the severe condition of high space velocity (600,000 mL g−1 h−1), all the catalysts were quite active, with values of CH4 conversion between 67% and 74% at 700 °C. In particular, the combination of cerium and gold enhanced the CH4 conversion up to 74%. Both additives, individually and simultaneously, enhanced the nickel dispersion with respect to the unpromoted NiAl and favored the reducibility of the nickel. During DRM all the catalysts formed graphitic carbon, contributing to their deactivation. The lower carbon gasification temperature of the promoted catalysts confirmed a positive effect played by Ce and Au in assisting the formation of an easier-to-remove carbon. The positive effect was testified by the better stability of the Ce/NiAl with respect to the other catalysts. In the gold-containing samples, this effect was neutralized by Au diffusing towards the catalyst surface during DRM, masking the nickel active sites. TPSR-CH4 test highlighted different CH4 activation capability of the catalysts. Furthermore, the comparison of the deposited carbon features (amount and removal temperature) of the DRM and TPSR spent catalysts indicated a superior activation of CO2 by the Au/Ce/NiAl, to be related to the close interaction of gold and ceria enhancing the oxygen mobility in the catalyst lattice.

Dry Reforming of Methane with Mesoporous Ni/ZrO2 Catalyst

Dry reforming of methane has exhibited significant environmental benefits as it utilizes two major greenhouse gases (CO2 and CH4) to produce synthesis gas, a major building block for hydrocarbons. This process has gained industrial attention as catalyst deactivation due to coke deposition being a major hindrance. The present study focuses on the dry reforming of methane over Ni-supported mesoporous zirconia support. Ni metal was loaded over in-house synthesized mesoporous zirconia within the 0–15 wt% range using the wet impregnation method. The physicochemical properties of the synthesized catalysts were studied using various characterization techniques, namely, XRD, SEM, FTIR, TGA, and N2 adsorption-desorption techniques. The activity of all the catalysts was evaluated at 750°C and gas hourly space velocity (GHSV) of 72000 ml/h/gcat for 9 hours (540 min). The deactivation factor indicating a loss in conversion with time is reported for each catalyst. 10 wt% Ni/ZrO2 showed the highest feed conversion of about 68.8% for methane and 70.2% for carbon dioxide and the highest stability (15.1% deactivation factor and 21% weight loss) for dry reforming of methane to synthesis gas.

Effect of Modified Alumina Support on the Performance of Ni-Based Catalysts for CO2 Reforming of Methane

The CO2 reforming of methane to syngas was examined over five different supported catalysts. In this study, 5% Ni was used as the active metal part of the catalyst. To better comprehend the impact of the supports on the catalytic properties, 5% Ni-based catalysts were characterized using nitrogen adsorption–desorption isotherms, XRD, H2-TPR, CO2-TPD, TGA, TPO, FTIR, and Raman. The results showed that the catalyst support with the highest surface area provided the best catalytic activity. The acquired CH4 and CO2 conversions at 700 °C were 58.2% and 67.6%, respectively, with a hydrogen/carbon ratio of 0.85. The TGA investigation of the high-surface-area sample produced a minimum carbon deposition of 11.2 wt.%, and in the CO2-TPD investigation, the high-surface-area sample exhibited the absence of a peak in the strong-basic-sites zone. The formation of NiAl2O4 spinel, moderate basicity, and the high surface area explained the outperformance of the high-surface-area catalyst sample.

The Ni Catalyst Supported on the FSP-made Transition Metal (Co, Mn, Cu or Zn) Doped La2O3 Material for the Dry Reforming of Methane

The transition metal (Co, Mn, Cu or Zn) doped La2O3 material was prepared by flame spray pyrolysis (FSP) technique. The 2 wt.% Ni catalyst supported on this material was characterized by XRD, N2 physisorption, TPR, H2 chemisorption and TGA, and evaluated by the dry reforming of methane (DRM). The perovskite structure was certainly formed when either Co or Mn was introduced. The Cu can generate the La2CuO4 spinel phase while the Zn showed a mixed phase of La2O3, ZnO and La(OH)3. The Ni/Co-La2O3 catalyst was more active for the DRM because of high amount of active dual sites of Ni and Co metals dispersed on the catalyst surface. The formation of La2O2CO3 during the reaction can inhibit the coke formation. The cooperation of La2O2CO3 and MnO phases in the Ni/Mn-La2O3 catalyst was promotional effect to decrease carbon deposits on the catalyst surface. The partial substitution of Co for Mn with a small content of Mn can enhance the catalytic activity and the product yield. The Ni/Mn0.05Co0.95-La2O3 catalyst showed the highest CH4 conversion, H2 yield and H2/CO ratio. The Mn inserted into the perovskite structure of LaCoO3 was an important player to change oxygen mobility within the crystal lattice to maintain a high performance of the catalyst. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

Catalysts Based on Strontium Titanate Doped with Ni/Co/Cu for Dry Reforming of Methane

Two series of strontium titanates doped with Ni, Co, or Cu with general formula of SrTi_1-xMe_xO₃ for Sr-stoichiometric and Sr_0.95Ti_1-xMe_xO₃ for Sr-non-stoichiometric materials (where Me = Ni, Co or Cu and x were 0.02 and 0.06) were obtained by the wet chemical method. The samples were calcinated at 900, 950, and 1050 °C and characterized in terms of their structural properties (XRD), the possibility of undergoing the reduction and oxidation reactions (TPR/TPOx), and catalytic properties. All obtained materials were multiphase and although the XRD analysis does not confirm the presence of Ni, Co, and Cu oxides (with one exception for Cu-doped sample), the TPR/TPOx profiles show reduction peaks that can be attributed to the reduction of these oxides which may at first appear in an amorphous form. Catalytic tests in dry reforming of methane reaction showed that the highest catalytic activity was achieved for Ni-doped materials (up to 90% of CH₄ conversion) while Co and Cu-doped samples showed only a very slight catalytic effect. Additionally, the decrease in methane conversion with an increasing calcination temperature was observed for Ni-doped strontium titanates.

Anti-Coking and Anti-Sintering Ni/Al2O3 Catalysts in the Dry Reforming of Methane: Recent Progress and Prospects

Coking and metal sintering are limitations of large-scale applications of Ni/Al2O3 catalysts in DRM reactions. In this review, several modification strategies to enhance the anti-deactivation property of Ni/Al2O3 are proposed and discussed with the recently developed catalyst systems, including structure and morphology control, surface acidity/basicity, interfacial engineering and oxygen defects. In addition, the structure–performance relationship and deactivation/anti-deactivation mechanisms are illustrated in depth, followed by prospects for future work.

The Effect of ZrO2 as Different Components of Ni-Based Catalysts for CO2 Reforming of Methane and Combined Steam and CO2 Reforming of Methane on Catalytic Performance with Coke Formation

The role of ZrO2 as different components in Ni-based catalysts for CO2 reforming of methane (CRM) has been investigated. The 10 wt.% Ni supported catalysts were prepared with ZrO2 as a support using a co-impregnation method. As a promoter (1 wt.% ZrO2) and a coactive component (10 wt.% ZrO2), the catalysts with ZrO2 were synthesized using a co-impregnation method. To evaluate the effect of the interaction, the Ni catalyst with ZrO2 as a coactive component was prepared by a sequential impregnation method. The results revealed that the activity, the selectivity, and the anti-coking ability of the catalyst depend upon the ZrO2 content, the Ni-ZrO2 interaction, basicity, and oxygen mobility of each catalyst resulting in different Ni dispersion and oxygen transfer pathway from ZrO2 to Ni. According to the characterization and catalytic activation results, the Ni catalyst with low ZrO2 content (as a promoter) presented highest selectivity toward CO owning to the high number of weak and moderate basic sites that enhance the CO2 activation-dissociation. The lowest activity (CH4 conversion ≈ 40% and CO2 conversion ≈ 39%) with the relatively high quantity of total coke formation (the weight loss of the spent catalyst in TGA curve ≈ 22%) of the Ni catalyst with ZrO2 as a support is ascribed to the lowest Ni dispersion due to the poor Ni-ZrO2 interaction and less oxygen transfer from ZrO2 to the deposited carbon on the Ni surface. The effect of a poor Ni-ZrO2 interaction on the catalytic activity was deducted by decreasing ZrO2 content to 10 wt.% (as a coactive component) and 1 wt.% (as a promoter). Although Ni catalysts with 1 wt.% and 10 wt.% ZrO2 provided similar oxygen mobility, the lack of oxygen transfer to coke during CRM process on the Ni surface was still indicated by the growth of carbon filament when the catalyst was prepared by co-impregnation method. When the catalyst was prepared by a sequential impregnation, the intimate interaction of Ni and ZrO2 for oxygen transfer was successfully developed through a ZrO2-Al2O3 composite. The interaction in this catalyst enhanced the catalytic activity (CH4 conversion ≈ 54% and CO2 conversion ≈ 50%) and the oxygen transport for carbon oxidation (the weight loss of the spent catalyst in TGA curve ≈ 7%) for CRM process. The Ni supported catalysts with ZrO2 as a promoter prepared by co-impregnation and with ZrO2 as a coactive component prepared by a sequential impregnation were tested in combined steam and CO2 reforming of methane (CSCRM). The results revealed that the ZrO2 promoter provided a greater carbon resistance (coke = 1.213 mmol·g−1) with the subtraction of CH4 and CO2 activities (CH4 conversion ≈ 28% and CO2 conversion ≈ %) due to the loss of active sites to the H2O activation-dissociation. Thus, the H2O activation-dissociation was promoted more efficiently on the basic sites than on the vacancy sites in CSCRM.

Dry Reforming of Methane Using Ni Catalyst Supported on ZrO2: The Effect of Different Sources of Zirconia

Dry reforming of methane (DRM) has a substantial potential to provide a cost-effective process and in reducing greenhouse gases. Its application has been hindered by carbon deposition and instability problems. The use of an appropriate catalyst is influenced by the support type. The objective of this investigation is to elucidate the effect of different sources of ZrO2 support. Four kinds of ZrO2, namely RC-100 and Z-3215, MKnano, and ELTN were acquired from Japan, Canada, and China, respectively. The catalyst samples were analyzed by BET, XRD, TPR, TPD, TEM, TGA, TPO, FT-IR, and Raman. The analysis of the structural properties displayed that all Ni-supported catalysts, regardless of their source, are mesoporous and that 5Ni-RC-100 possessed the highest BET surface area of 17.7 m2/g and 5Ni-MKnano had the lowest value of BET 3.16 m2/g. In the TPD and TEM analysis, the 5Ni-RC-100 catalyst presented the highest intensity of basicity and the minimum average particle size of 3.35 nm, respectively. The 5Ni-RC-100 catalyst outperformed 5Ni-ELTN by exhibiting 44% higher CH4 conversion; however, 5Ni-RC-100 gave the highest weight loss in the TGA analysis of 66%.

Dry Reforming of Methane over Carbon Fibre-Supported CeZrO2, Ni-CeZrO2, Pt-CeZrO2 and Pt-Ni-CeZrO2 Catalysts

Dry reforming of methane (DRM) is one of the most important processes allowing transformation of two most potent greenhouse gases into a synthesis gas. The CH4 and CO2 are converted at high temperatures in the presence of a metal catalyst (usually Ni, also promoted with noble metals, supported over various oxides). The DRM process is not widely used in the gas processing industry because of prompt deactivation of the catalyst owing to carbon deposition and the blockage of the metal active sites. This problem can be hindered by proper design of the catalyst in terms, e.g., of its composition and by providing strong interaction between active metal and catalytic support. The properties of the latter are also crucial for the catalyst’s performance in DRM and the occurrence of parallel reactions such as reverse water gas shift, CO2 deoxidation or carbon formation. In this paper we show for the first time the DRM performance of the ceria-zirconia and metal (Ni and/or Pt) supported on carbon fibres. The obtained Ni and Ni-Pt containing catalysts showed relatively high activity in the studied reaction and high resistance towards carbon deposition.

Role of Mixed Oxides in Hydrogen Production through the Dry Reforming of Methane over Nickel Catalysts Supported on Modified γ-Al2O3

H2 production through dry reforming of methane (DRM) is a hot topic amidst growing environmental and atom-economy concerns. Loading Ni-based reducible mixed oxide systems onto a thermally stable support is a reliable approach for obtaining catalysts of good dispersion and high stability. Herein, NiO was dispersed over MOx-modified-γ-Al2O3 (M = Ti, Mo, Si, or W; x = 2 or 3) through incipient wetness impregnation followed by calcination. The obtained catalyst systems were characterized by infrared, ultraviolet–visible, and X-ray photoelectron spectroscopies, and H2 temperature-programmed reduction. The mentioned synthetic procedure afforded the proper nucleation of different NiO-containing mixed oxides and/or interacting-NiO species. With different modifiers, the interaction of NiO with the γ-Al2O3 support was found to change, the Ni2+ environment was reformed exclusively, and the tendency of NiO species to undergo reduction was modified greatly. Catalyst systems 5Ni3MAl (M = Si, W) comprised a variety of species, whereby NiO interacted with the modifier and the support (e.g., NiSiO3, NiAl2O4, and NiWO3). These two catalyst systems displayed equal efficiency, >70% H2 yield at 800 °C, and were thermally stable for up to 420 min on stream. 5Ni3SiAl catalyst regained nearly all its activity during regeneration for up to two cycles.

Recent Progresses in the Design and Fabrication of Highly Efficient Ni-Based Catalysts With Advanced Catalytic Activity and Enhanced Anti-coke Performance Toward CO2 Reforming of Methane

CO₂ reforming of methane (CRM) can effectively convert two greenhouse gases (CO₂ and CH₄) into syngas (CO + H₂). This process can achieve the efficient resource utilization of CO₂ and CH₄ and reduce greenhouse gases. Therefore, CRM has been considered as a significantly promising route to solve environmental problems caused by greenhouse effect. Ni-based catalysts have been widely investigated in CRM reactions due to their various advantages, such as high catalytic activity, low price, and abundant reserves. However, Ni-based catalysts usually suffer from rapid deactivation because of thermal sintering of metallic Ni active sites and surface coke deposition, which restricted the industrialization of Ni-based catalysts toward the CRM process. In order to address these challenges, scientists all around the world have devoted great efforts to investigating various influencing factors, such as the option of appropriate supports and promoters and the construction of strong metal-support interaction. Therefore, we carefully summarized recent development in the design and preparation of Ni-based catalysts with advanced catalytic activity and enhanced anti-coke performance toward CRM reactions in this review. Specifically, recent progresses of Ni-based catalysts with different supports, additives, preparation methods, and so on, have been summarized in detail. Furthermore, recent development of reaction mechanism studies over Ni-based catalysts was also covered by this review. Finally, it is prospected that the Ni-based catalyst supported by an ordered mesoporous framework and the combined reforming of methane will become the future development trend.

Carbon Dioxide Reforming of Methane over Ni Supported SiO2: Influence of the Preparation Method on the Resulting Structural Properties and Catalytic Activity

Ni-C/SiO2 and Ni-G/SiO2 catalysts were prepared by a complexed-impregnation method using citric acid and glycine as complexing agents, respectively. Ni/SiO2 was also prepared by the conventional incipient impregnation method. All the catalysts were comparatively tested for carbon dioxide reforming of methane (CDR) at P = 1.0 atm, T = 750 °C, CO2/CH4 = 1.0, and GHSV = 60,000 mL·g−1·h−1. The results showed that Ni-C/SiO2 and Ni-G/SiO2 exhibited better CDR performance, especially regarding stability, than Ni/SiO2. The conversions of CH4 and CO2 were kept constant above 82% and 87% after 20 h of reaction over Ni-C/SiO2 and Ni-G/SiO2 while they were decreased from 81% and 88% to 56% and 59%, respectively, over the Ni/SiO2. The characterization results of the catalysts before and after the reaction showed that the particle size and the distribution of Ni, as well as the interactions between Ni and the support were significantly influenced by the preparation method. As a result, an excellent resistance to the coking deposition and the anti-sintering of Ni was obtained over the Ni-C/SiO2 and Ni-G/SiO2, leading to a highly active and stable CDR performance.

Recent Progresses in Constructing the Highly Efficient Ni Based Catalysts With Advanced Low-Temperature Activity Toward CO2 Methanation

With the development and prosperity of the global economy, the emission of carbon dioxide (CO2) has become an increasing concern. Its greenhouse effect will cause serious environmental problems, such as the global warming and climate change. Therefore, the worldwide scientists have devoted great efforts to control CO2 emissions through various strategies, such as capture, resource utilization, sequestration, etc. Among these, the catalytic conversion of CO2 to methane is considered as one of the most efficient routes for resource utilization of CO2 owing to the mild reaction conditions and simple reaction device. Pioneer thermodynamic studies have revealed that low reaction temperature is beneficial to the high catalytic activity and CH4 selectivity. However, the low temperature will be adverse to the enhancement of the reaction rate due to kinetic barrier for the activation of CO2. Therefore, the invention of highly efficient catalysts with promising low temperature activities toward CO2 methanation reaction is the key solution. The Ni based catalysts have been widely investigated as the catalysts toward CO2 methanation due to their low cost and excellent catalytic performances. However, the Ni based catalysts usually perform poor low-temperature activities and stabilities. Therefore, the development of highly efficient Ni based catalysts with excellent low-temperature catalytic performances has become the research focus as well as challenge in this field. Therefore, we summarized the recent research progresses of constructing highly efficient Ni based catalysts toward CO2 methanation in this review. Specifically, the strategies on how to enhance the catalytic performances of the Ni based catalysts have been carefully reviewed, which include various influencing factors, such as catalytic supports, catalytic auxiliaries and dopants, the fabrication methods, reaction conditions, etc. Finally, the future development trend of the Ni based catalysts is also prospected, which will be helpful to the design and fabrication of the Ni catalysts with high efficiency toward CO2 methanation process.

The Distinctive Effects of Glucose-Derived Carbon on the Performance of Ni-Based Catalysts in Methane Dry Reforming

This study aimed to investigate the effect of carbon derived from glucose (C) on the physicochemical characteristics and catalytic activity of Ni, supported over SiO2, ZSM-5, and TiO2 in methane dry reforming. Among the Ni catalysts without C, Ni/SiO2 exhibited the highest CH4-CO2 conversion and stability at all experimented temperatures. On the other hand, the C-incorporated catalysts prepared by glucose impregnation, followed by pyrolysis, showed dissimilar performances. C improved the stability of Ni/SiO2 in the reforming at 650 °C and 750 °C and increased the CH4 and CO2 conversion to the level close to the thermodynamic equilibrium at 850 °C. However, this element did not substantially affect the activity of Ni/ZSM-5 and exerted a retarding effect on Ni/TiO2. Characterizations with H2-TPD, XRD, EXAFS, and STEM-EDS revealed that the different influences of C by the supports were attributed to the extent of metal dispersion and metal-support interaction.

The Relationship between Reaction Temperature and Carbon Deposition on Nickel Catalysts Based on Al2O3, ZrO2 or SiO2 Supports during the Biogas Dry Reforming Reaction

The tackling of carbon deposition during the dry reforming of biogas (BDR) necessitates research of the surface of spent catalysts in an effort to obtain a better understanding of the effect that different carbon allotropes have on the deactivation mechanism and correlation of their formation with catalytic properties. The work presented herein provides a comparative assessment of catalytic stability in relation to carbon deposition and metal particle sintering on un-promoted Ni/Al2O3, Ni/ZrO2 and Ni/SiO2 catalysts for different reaction temperatures. The spent catalysts were examined using thermogravimetric analysis (TGA), Raman spectroscopy, high angle annular dark field scanning transmission electron microscopy (STEM-HAADF) and X-ray photoelectron spectroscopy (XPS). The results show that the formation and nature of carbonaceous deposits on catalytic surfaces (and thus catalytic stability) depend on the interplay of a number of crucial parameters such as metal support interaction, acidity/basicity characteristics, O2– lability and active phase particle size. When a catalytic system possesses only some of these beneficial characteristics, then competition with adverse effects may overshadow any potential benefits.