Gas Chromatography

Point-of-care community drug checking technologies: an insider look at the scientific principles and practical considerations

Drug checking is increasingly being explored outside of festivals and events to be an ongoing service within communities, frequently integrated within responses to illicit drug overdose. The choice of instrumentation is a common question, and the demands on these chemical analytical instruments can be challenging as illicit substances may be more complex and include highly potent ingredients at trace levels. The answer remains nuanced as the instruments themselves are not directly comparable nor are the local demands on the service, meaning implementation factors heavily influence the assessment and effectiveness of instruments. In this perspective, we provide a technical but accessible introduction to the background of a few common drug checking methods aimed at current and potential drug checking service providers. We discuss the following tools that have been used as part of the Vancouver Island Drug Checking Project in Victoria, Canada: immunoassay test strips, attenuated total reflection IR-absorption spectroscopy, Raman spectroscopy from powder samples, surface-enhanced Raman scattering in a solution of colloidal gold nanoparticles, and gas chromatography-mass spectrometry. Using four different drug mixtures received and tested at the service, we illustrate the strengths, limitations, and capabilities of such instruments, and expose the scientific theory to give further insight into their analytical results. Each case study provides a walk-through-style analysis for a practical comparison between data from several different instruments acquired on the same sample. Ideally, a single instrument would be able to achieve all of the objectives of drug checking. However, there is no clear instrument that ticks every box; low cost, portable, rapid, easy-to-use and provides highly sensitive identification and accurate quantification. Multi-instrument approaches to drug checking may be required to effectively respond to increasingly complex and highly potent substances demanding trace level detection and the potential for quantification.

The Application of In Situ Methods to Monitor VOC Concentrations in Urban Areas—A Bibliometric Analysis and Measuring Solution Review

Urbanisation development affects urban vegetation both directly and indirectly. Since this process usually involves a dramatic change in land use, it is seen as likely to cause ecological pressure on local ecosystems. All forms of human activity, including urbanisation of areas close to residential buildings, significantly impact air quality. This study aims to identify and characterise different measurement solutions of VOCs, allowing the quantification of total and selective compounds in a direct at source (in situ) manner. Portable devices for direct testing can generally be divided into detectors, chromatographs, and electronic noses. They differ in parameters such as operating principle, sensitivity, measurement range, response time, and selectivity. Direct research allows us to obtain measurement results in a short time, which is essential from the point of view of immediate reaction in the case of high concentrations of tested compounds and the possibility of ensuring the well-being of people. The paper also attempts to compare solutions and devices available on the market and assess their application.

Man-portable laser-induced breakdown spectroscopy system for in situ characterization of karstic formations

This paper reports the development and field testing of a man-portable instrument based on laser-induced breakdown spectrometry (LIBS) for inspection and analysis of speleothems. The 50 mJ of a Q-switched Nd:YAG laser operating at 1064 nm was used to generate a plasma on the sample. Plasma emission was then guided using a fiber-optic cable to a 1/10 m spectrometer equipped with a charge-coupled device (CCD) array detector. Plasma light was automatically processed in order to obtain surface and in-depth information from the speleothems. A field campaign in the interior of Nerja Cave (a large karstic formation in the South of Spain) has been carried out, aimed at evaluating the analytical performance of the instrument when operating in an unfriendly environment. Identification analysis of the speleothems' alteration layers and depth profiles of Sr and Ca is carried out and reported.

Sample preparation for the analysis of volatile organic compounds in air and water matrices

This review summarizes literature data from the past 5 years on new developments and/or applications of sample preparation methods for analysis of volatile organic compounds (VOC), mainly in air and water matrices. Novel trends in the optimization and application of well-established airborne VOC enrichment techniques are discussed, like the implementation of advanced cooling systems in cryogenic trapping and miniaturization in adsorptive enrichment techniques. Next, focus is put on current tendencies in integrated sampling-extraction-sample introduction methods such as solid phase microextraction (SPME) and novel in-needle trapping devices. Particular attention is paid to emerging membrane extraction techniques such as membrane inlet mass spectrometry (MIMS) and membrane extraction with a sorbent interface (MESI). For VOC enrichment out of water, recent evolutions in direct aqueous injection (DAI) and liquid-liquid extraction (LLE) are highlighted, with main focus on miniaturized solvent extraction methods such as single drop microextraction (SDME) and liquid phase microextraction (LPME). Next, solvent-free sorptive enrichment receives major attention, with particular interest for innovative techniques such as stir bar sorptive extraction (SBSE) and solid phase dynamic extraction (SPDE). Finally, recent trends in membrane extraction are reviewed. Applications in both immersion and headspace mode are discussed.

Performance characteristics of a new prototype for a portable GC using ambient air as carrier gas for on-site analysis

The performance characteristics of a portable GC instrument requiring no compressed gas supplies and using relatively lightweight transportable components for the analysis of volatile organic components in large-volume air samples are described. To avoid the need for compressed gas tanks, ambient air is used as the carrier gas, and a vacuum pump is used to pull the carrier gas and injected samples through the wall-coated capillary column and a photoionization detector (PID). At-column heating is used eliminating the need for a conventional oven. The fused silica column is wrapped with heater wire and sensor wire so that heating is provided directly at the column. A PID is used since it requires no external gas supplies and has high sensitivity for many compounds of interest in environmental air monitoring. In order to achieve detection limits in the ppb range, an online multibed preconcentrator containing beds of graphitized carbons and carbon molecular sieves is used. After sample collection, the flow direction through the preconcentrator is reversed, and the sample is thermally desorbed directly into the column. Decomposition of sensitive compounds during desorption is greater with air as the carrier gas than with hydrogen.

Investigation of high-speed gas chromatography using synchronized dual-valve injection and resistively heated temperature programming

High-speed temperature programming is implemented via the direct resistive heating of the separation column (2.3m MXT-5 Silicosteel column with a 180 microm I.D. and a 0.4 microm 5% phenyl/95% dimethyl polysiloxane film). Resistive temperature programming was coupled with synchronized dual-valve injection (with an injection pulse width of 2 ms), producing a complete high-speed gas chromatography (GC) system. A comparison of isothermal and temperature programmed separations of seven n-alkanes (C(6) and C(8)-C(13)) shows a substantial improvement of peak width and peak capacity with temperature programming. The system was further implemented in separations of a mixture of analytes from various chemical classes. Separations of the n-alkane mixture using three different temperature programming rates are reported. A temperature programming rate as high as 240 degrees C/s is demonstrated. The method for determination of temperature programming rate, based on isothermal data, is discussed. The high-speed resistive column heating temperature programming resulted in highly reproducible separations. The highest rate of temperature programming (240 degrees C/s) resulted in retention time and peak width RSD, on average, of 0.5 and 1.4%, respectively, for the n-alkane mixture. This high level of precision was achieved with peak widths-at-half-height ranging from 13 to 36 ms, and retention times ranging from 147 to 444 ms (for n-hexane to n-tridecane).

Surface derivatization of poly(p-phenylene terephthalamide) fiber designed for novel separation and extraction media

The surface derivatization of poly(p-phenylene terephthalamide) fiber was studied. The obtained surface-derivatized filaments were packed into a fused-silica capillary to evaluate its surface characteristics by using GC. As the stationary phase for GC the surface-derivatized fibers showed higher retention for alkanes and alkylbenzenes than that with the untreated Kevlar fiber. The improvements on the retention power and the peak shape were observed on the benzyl-modified fibrous stationary phase. The derivatized fibrous materials were also evaluated as the extraction medium in fiber-in-tube SPE, and the effect of the surface modification on the extraction power was compared to the parent fiber. The results indicated that the modified fiber possessed a higher extraction power than the untreated fiber. Based on the facts, the successful modification of the fiber surface was estimated.