Cloud Point Extraction Coupled with Microwave or Ultrasonic Assisted Back Extraction as a Preconcentration Step Prior to Gas Chromatography

Compatibility of cloud point extraction with gas chromatography: Matrix effects of Triton X-100 on GC-MS and GC-MS/MS analysis of organochlorine and organophosphorus pesticides

Cloud point extraction is an environmentally benign and simple separation/concentration procedure that can be regarded as an alternative to classical liquid-liquid extraction. In the current work, it was studied the compatibility of cloud point extraction followed by back-extraction in low volume of organic solvent with gas chromatography-mass spectrometry (GC-MS and GC-MS/MS). Triton X-100 was preferred than Triton X-114 as a surfactant to produce the clouding phenomenon and hexane or isooctane was found to be appropriate organic solvents which can be used at the back-extraction step. It was observed that ca. 0.09 % w/w Triton X-100 was co-extracted in the organic phase (hexane or isooctane) so further study was carried out to find out its effect on the GC-MS (GC-MS/MS) measurement when liquid samples are injected without any pre-cleaning to remove the surfactant. The chromatographic separation and the mass detection were not deteriorated by the concomitant Triton X-100 for analysis of several Organochlorine and Organophosphorus pesticides (alpha-HCH, beta-HCH, gamma-HCH, Pentachlorobenzene, Hexachlorobenzene, Chlorpyrifos, Chlorpyrifos-methyl, Aldrin, Endrin, Dieldrin, alpha-Endosulfan, Heptachlor, Heptachlor-endo-epoxide-A, o,p-DDD, p,p-DDD, o,p-DDE, p,p-DDE, o,p-DDT and p,p-DDT). The stability of the GC system when introducing surfactant was assessed as acceptable (typically the peak area RSD% for 20 consecutive injections were below 5 %). Under the developed vaporization conditions using PTV or PSS injectors it can be deduced that Triton X-100 is deposited on the inner surface of the liner. This effect is beneficial since the resulting surfactant layer makes a surface which facilitates the pesticides transfer to the GC column. As a consequence, for some analytes, a substantial enhancement (up to 2.3 times) in the sensitivity was observed when the matrix-matched medium (0.09 % w/w Triton X-100 in organic solvent) is used compared to calibration in solely hexane or isooctane. Meanwhile, the measurement precision in the presence of Triton X-100 remains unchanged. The GC-MS/MS analysis was alternatively accomplished by the use of glass or metal liner and it was found that the glass one should be preferable. Finally, it can be concluded that cloud point extraction with Triton X-100 can be combined with GC-MS or GC-MS/MS analysis by applying liquid injection of the target analytes transferred in organic solvents such as hexane or isooctane. We have established a positive effect of Triton X-100 on the instrumental performance which is on opposite to the generally accepted concern of the negative influence of the surfactants on the gas chromatographic analysis.

Homogeneous liquid-liquid extraction as an alternative sample preparation technique for biomedical analysis

Liquid-liquid extraction is a widely used technique of sample preparation in biomedical analysis. In spite of the high pre-concentration capacities of liquid-liquid extraction, it suffers from a number of limitations including time and effort consumption, large organic solvent utilization, and poor performance in highly polar analytes. Homogeneous liquid-liquid extraction is an alternative sample preparation technique that overcomes some drawbacks of conventional liquid-liquid extraction, and allows employing greener organic solvents in sample treatment. In homogeneous liquid-liquid extraction, a homogeneous phase is formed between the aqueous sample and the water-miscible extractant, followed by chemically or physically induced phase separation. To form the homogeneous phase, aqueous samples are mixed with water-miscible organic solvents, water-immiscible solvents/cosolvents, surfactants, or smart polymers. Then, phase separation is induced chemically (adding salt, sugar, or buffer) or physically (changing temperature or pH). This mode is rapid, sustainable, and cost-effective in comparison with other sample preparation techniques. Moreover, homogeneous liquid-liquid extraction is more suitable for the extraction of delicate macromolecules such as enzymes, hormones, and proteins and it is more compatible with liquid chromatography with tandem mass spectrometry, which is a vital technique in metabolomics and proteomics. In this review, the principle, types, applications, automation, and technical aspects of homogeneous liquid-liquid extraction are discussed.

Progress in Pretreatment and Analytical Methods of Coumarins: An Update since 2012 - A Review

Coumarins are widely used due to their wide range of biological activities, but the long-term or excessive use of coumarin flavors can pose serious health hazards. Therefore, sensitive and specific methods for the quantification of these compounds in different matrices have been developed. In this review, an updated overview of the latest trends in sample preparation techniques and methods used to detect coumarins from March 2012 to April 2019 is provided. This study reviews different analytical methods (such as liquid chromatography coupled with different detectors, electrochemical sensors, capillary electrophoresis, etc.) and different pretreatment methods (such as liquid-liquid extraction, solid-phase extraction, dispersive liquid-liquid microextraction, etc.). Different methods for the pretreatment and determination of coumarins in plant, food, environmental, pharmaceutical and biological samples are summarized, discussed and compared.HighlightsProgress in pretreatment and analytical methods of coumarins are summarized.Fundamentals, instrumentation and applications of purification and quantification are summarized and compared.Optimization of experimental conditions are discussed.Newly emerged eco-friendly methods are introduced.

Twenty years of supramolecular solvents in sample preparation for chromatography: achievements and challenges ahead

Supramolecular solvents (SUPRAS) have progressively become a suitable alternative to organic solvents for sample preparation in chromatographic analysis. The inherent properties of these nanostructured solvents (e.g. different polarity microenvironments, multiple binding sites, possibility of tailoring their properties, etc.) offer multiple opportunities for the development of innovative sample treatment platforms not approachable by conventional solvents. In this review, major achievements attained in the combination SUPRAS-chromatography in the last 20 years as well as the challenges that should be addressed in the near future are critically discussed. Among achievements, particular attention is paid to the theoretical and practical knowledge gained that has helped make substantial progress in the area. In this respect, advances in the understanding of the mechanisms involved in SUPRAS formation and SUPRAS-solute interactions driving extractions are discussed, with a view to the setting up of knowledge-based extraction procedures. Likewise, the strategies followed to improve the compatibility of SUPRAS extracts with liquid and gas chromatography and adapt SUPRAS-based extractions to different formats are presented. Ongoing efforts to apply SUPRAS in multicomponent extractions and synthesize tailored SUPRAS for the development of innovative sample treatments are highlighted. Among challenges identified, discussion is focused on the automation of SUPRAS-based sample treatment and the elucidation of SUPRAS nanostructures, which are considered essential for their acceptance in routine labs and the design of tailored SUPRAS with programmed functions. Graphical abstract.

Cloud point extraction coupled with back extraction: a green methodology in analytical chemistry

Recently, cloud point extraction (CPE) coupled with back extraction (BE) has been suggested as a promising alternative to liquid-liquid extraction. In CPE, non-ionic surfactants in aqueous solutions form micelles and the solution becomes turbid when heated to the cloud point temperature. Microwave- or ultrasonic-assisted BE can be performed after CPE and before injection of the sample for instrumental analysis by ultraviolet-visible spectroscopy, high-performance liquid chromatography, gas chromatography, gas chromatography-mass spectrometry, or liquid chromatography-mass spectrometry. This article reviews selected published scientific research on the application of CPE-BE to the determination of alkaloids, drugs and organophosphorus compounds from several complex matrices. This method could be scaled-up for use in forensic science.

Use of 2-Hydrazinobenzothiazole-Modified Copolymer(s) as Potential Chelating Agent for Sensitive and Selective Determination of Low Levels of Mercury in Seafood by Ultrasound-Assisted Cloud-Point Extraction Combined with Spectrophotometry

In this study, a new method was developed for the pre-concentration of trace mercury from seafood samples prior to analysis by spectrophotometry. The method is based on the complexation between 2-hydrazinobenzothiazole (2-HBT)-modified copolymer(s) and Hg(II) in the presence of an ionic surfactant, cetyltrimethylammonium bromide (CTAB), as sensitivity enhancer at pH 4.5 and the extraction of the complex into the surfactant-rich phase of polyethylene glycol tert-octylphenyl ether (Triton X-114) as the extractant. The variables affecting extraction efficiency were evaluated and optimized. Due to the observation that the modified copolymers are 2.5-fold more sensitive and selective to the Hg²⁺ ions than the CH₃Hg⁺, the amounts of free Hg²⁺ and total Hg were determined at 325 nm by spectrophotometric detection of free Hg²⁺ and total Hg in the pre-treated and extracted fish samples using dilute acid mixture containing Triton X-114 and K₂Cr₂O₇, before and after oxidation of CH₃Hg⁺ to Hg²⁺ with mixture of KBr and KBrO₃ in the acidic media. The amount of CH₃Hg⁺ was calculated from the difference between total Hg and free Hg²⁺ amounts. The accuracy was tested by analysis of two certified samples. The results were statistically in good agreement with the certified values, and the precision was lower than 6.4%. The limits of detection were 1.40 (1.58) and 1.91 (2.11) μg L^-1 for Hg²⁺ from the two calibration solutions spiked before the pre-treatment, respectively. It has been observed that there is no significant matrix effect by comparison of slopes of the calibration curves. The method was applied to seafood samples for speciation analysis of free Hg²⁺ and CH₃Hg⁺. In terms of speciation, while total Hg is detected in the range of 12.6-143.8 μg kg^-1, the distribution of mercury in seafood was in the range of 7.4-53.3 μg kg^-1 for CH₃Hg⁺ and in 8.3-90.5 μg kg^-1 for free Hg²⁺.

Cloud-Point Extraction Combined with Thermal Degradation for Nanoplastic Analysis Using Pyrolysis Gas Chromatography-Mass Spectrometry

The contamination of micro- and nanoplastics in marine systems and freshwater is a global issue. Determination of micro- and nanoplastics in the aqueous environment is of high priority to fully assess the risk that plastic particles will pose. Although microplastics have been detected in a variety of aquatic ecosystems, the analysis of nanoplastics remains an unsolved challenge. Herein, for the first time, a Triton X-45 (TX-45)-based cloud-point extraction (CPE) was proposed to preconcentrate trace nanoplastics in environmental waters. Under the optimum extraction conditions, an enrichment factor of 500 was obtained for two types of nanoplastics with different compositions, polystyrene (PS) and poly(methyl methacrylate) (PMMA), without disturbing their original morphology and sizes. Additionally, following thermal treatment at 190 °C for 3 h, the CPE-obtained extract could be submitted to pyrolysis gas chromatography-mass spectrometry (Py-GC/MS) analysis for mass quantification of nanoplastics. Taking 66.2 nm PS nanoplastics and 86.2 nm PMMA nanoplastics as examples, the proposed method showed excellent reproducibility, and high sensitivity with respective detection limits of 11.5 and 2.5 fM. Feasibility of the proposed approach was verified by application of the optimized procedure to four real water samples. Recoveries of 84.6-96.6% at a spiked level of 88.6 fM for PS nanoplastics and 76.5-96.6% at a spiked level of 50.4 fM for PMMA nanoplastics were obtained. Consequently, this work provides an efficient approach for nanoplastic analysis in environmental waters.

A novel liquid-liquid extraction for the determination of naphthalene by GC-MS with deuterated anthracene as internal standard

Polycyclic aromatic hydrocarbons are known for their carcinogenic and mutagenic effects on human health. This therefore calls for the regulation of their concentrations in air, water, and soil. Naphthalene as the simplest in structure of the polycyclic aromatic hydrocarbons is mainly used as a starter material for other chemicals but also has impacts on human health. A method is therefore proposed for the determination of naphthalene in water samples by gas chromatography mass spectrometry after liquid-liquid extraction. The extraction method was optimized to improve the extraction output, thereby lowering the limit of detection. The limits of detection and quantification obtained for naphthalene were 4.4 and 14.6 ng mL^-1, respectively. Deuterated anthracene was used as internal standard to enhance the precision of the method, for which a relative standard deviation of 4.3% was obtained. The percent recovery of naphthalene obtained from tap water was ranged between 93.8 and 102.2.

Determination of photoinitiator 4-methylbenzophenone in milk by cloud point extraction

An efficient and easy sample pretreatment methodology was proposed for the detection of photoinitiator 4-methylbenzophenone from milk before high-performance liquid chromatography. Appropriate conditions for demulsification were studied. The parameters affecting cloud point extraction, such as concentration of Tween-20, electrolyte salt, equilibration temperature, and time, have been investigated. When the spiked level was 200-1000 μg/kg, the average addition standard recovery was 99.14-105.98% with the optimum cloud point extraction conditions (concentration of Tween-20, 138 g/L; mass of anhydrous sodium sulfate, 0.75 g; equilibration temperature, 65°C; equilibration time, 30 min). To decrease the detection limits, further work about the organic solvent, shaking time, and ultrasonic parameters was carried. When the spiked level was 10-100 μg/kg, the average addition standard recovery was 70.40-106.91% with the optimum cloud point extraction and enrichment conditions (optimum cloud point extraction conditions; volume of cyclohexane, 30 mL; shaking time, 20 min; time of ultrasonic, 20 min; temperature of ultrasonic bath, 45°C).

Analysis of sulfonamides in soil, sediment, and sludge based on dynamic microwave-assisted micellar extraction

A green and high-throughput analytical method was described for the simultaneous determination of ten sulfonamides (SAs) from soil, sediment, and sludge in northeast China. None of potentially hazardous organic solvents was used in the whole sample preparation procedure, and the total preparation time of 15 samples was about 18 min. The limits of detection for the SAs were in the range of 0.42-0.68 ng g(-1). The intra-day and inter-day precisions, expressed by the relative standard deviation, were below 7 %. Under the optimum conditions, the recoveries of ten SAs were between 69.7 and 102.7 %. The proposed method was successfully applied to analyze the SAs residues in agricultural soils, river sediments, and sewage sludge. SAs were found at the levels of 1.40-2.31 ng g(-1) and 3.77-29.29 ng g(-1) in the sediments and sludge, respectively. The aging effect of spiked soil samples on the SAs recoveries was examined, and the results demonstrate that eight SAs could persist in five soils for 3 months. Compared with the traditional method, the proposed method could reduce the consumption of the organic solvent, shorten the sample preparation time, and increase the sample throughput.

Determination of low levels of polycyclic aromatic hydrocarbons in soil by high performance liquid chromatography with tandem fluorescence and diode-array detectors

Risk assessment of polycyclic aromatic hydrocarbons (PAHs) contaminated soil and source apportionment require accurate analysis of the concentration of each PAH congener in the soil. However, determination of low level PAH congeners in soil is difficult because of similarity in the chemical properties of 16 PAHs and severe matrix interferences due to complex composition of soils. It is therefore imperative to develop a sensitive and accurate method for determination of low level PAHs in soil. In this work, high performance liquid chromatography equipped with fluorescence and diode-array detectors (HPLC-FLD-DAD) was used to determine the concentration of 16 PAHs in soil. The separation of the 16 PAHs was achieved by optimization of the mobile phase gradient elution program and FLD wavelength switching program. Qualitative analysis of the 16 PAHs was based on the retention time (RT) and each PAH specific spectrum obtained from DAD. In contrast, the quantitative analysis of individual PAH congeners was based on the peak areas at the specific wavelength with DAD and FLD. Under optimal conditions the detection limit was in the range 1.0-9.5 μg L(-1) for 16 PAHs with DAD and 0.01-0.1 μg L(-1) for 15 PAHs with FLD, and the RSD of PAHs was less than 5% with DAD and 3% with FLD. The spiked recoveries were in the range 61-96%, with the exception of NaP (<40%). The results show that HPLC-FLD-DAD can provide more accurate and reliable analysis of low level PAH congeners in soil samples.

Analytical sonochemistry; developments, applications, and hyphenations of ultrasound in sample preparation and analytical techniques

Ultrasonic assistance is one of the great successes of modern analytical chemistry, which uses this energy for a variety of purposes in relation to sample preparation and development of methods for the analysis of numerous contaminants including organic and inorganic compounds. This review will attempt to provide an overview of more recent applications of ultrasound in different environmental and biological samples such as food, soil and water as well as a brief description of the theoretical understanding of this method. Also, the possibility of coupling ultrasound with other analytical techniques will be discussed.

Investigation of analytical performance for rapidly synergistic cloud point extraction of trace amounts of copper combined with spectrophotometric determination

In this work, an improved preconcentration method named as rapidly synergistic cloud point extraction (RS-CPE) was established for copper preconcentration and determination. Non-ionic surfactant Triton X-100 (TX-100) was used as extractant. Octanol worked as cloud point revulsant and synergic reagent, which successfully decreased the cloud point temperature (CPT) of TX-100 to realize the room temperature (about 20°C) CPE without heating. The established RS-CPE pretreatment was simple, rapid and effective. Compared with traditional CPE (about 40 min for heating, incubation and cooling), the extraction time of the proposed method was very short (1 min). The improved extraction technique RS-CPE was combined with traditional spectrophotometer to improve the analytical performance and expand the application of spectrophotometric determination. The influence factors relevant to RS-CPE, such as concentrations of TX-100 and octanol, concentration of chelating agent, pH, conditions of phase separation, salt effect, environmental temperature and instrumental conditions, were studied in detail. Under the optimal conditions, the limit of detection (LOD) for copper was 0.4 μg L(-1), with sensitivity enhancement factor (EF) of 18. The proposed method was applied to the determination of trace copper in real samples and certified samples with satisfactory analytical results.

Determination of triazole fungicides in environmental water samples by high performance liquid chromatography with cloud point extraction using polyethylene glycol 600 monooleate

A preconcentration technique known as cloud point extraction was developed for the determination of trace levels of triazole fungicides tricyclazole, triadimefon, tebuconazole and diniconazole in environmental waters. The triazole fungicides were extracted and preconcentrated using polyethylene glycol 600 monooleate (PEG600MO) as a low toxic and environmentally benign nonionic surfactant, and determined by high performance liquid chromatography/ultraviolet detection (HPLC-UV). The extraction conditions were optimized for the four triazole fungicides as follows: 2.0 wt% PEG600MO, 2.5 wt% Na(2)SO(4), equilibration at 45°C for 10 min, and centrifugation at 2000 rpm (533 × g) for 5 min. The triazole fungicides were well separated on a reversed-phase kromasil ODS C(18) column (250 mm × 4.6 mm, 5 μm) with gradient elution at ambient temperature and detected at 225 nm. The calibration range was 0.05-20 μg L(-1) for tricyclazole and 0.5-20 μg L(-1) for the other three classes of analytes with the correlation coefficients over 0.9992. Preconcentration factors were higher than 60-fold for the four selected fungicides. The limits of detection were 6.8-34.5 ng L(-1) (S/N=3) and the recoveries were 82.0-96.0% with the relative standard deviations of 2.8-7.8%.

Detection of trace anthracene in soil samples with real-time fluorescence quantitative immuno-PCR using a molecular beacon probe

We developed a highly sensitive and robust real-time fluorescence quantitative immuno-PCR (RTFQ-IPCR) method which uses molecular beacon (MB) probe to detect trace anthracene in the environment. This method was performed on serial dilutions of known anthracene concentrations equivalent to 10-fold dilutions of 10fg/mL to 100pg/mL. We obtained a linear relationship between 10fg/mL and 100pg/mL, with y=0.684x+13.221. A correlation coefficient of 0.994 was also identified, with a detection limit of 4.5fg/mL. After investigating the presence of anthracene in soil samples via RTFQ-IPCR, the obtained concentrations were confirmed by ELISA to be correct and believable, with the recovery ratio ranging from 82% to 112.5%. Based on its sensitivity and reproducibility, MB-based RTFQ-IPCR was found to be acceptable for use in on-site field tests to provide rapid, quantitative, and reliable test results for making environmental decisions.