Preparation of Sulfoxide Residue Bonded Silica Stationary Phase for Separation of Polychlorinated Biphenyls from Mineral Oils

Electrochemical Sulfoxidation of Thiols and Alkyl Halides

Sulfoxides are actively engaged as versatile synthetic building blocks, chiral ligands, bioactive molecules, and function materials. However, their oxidative syntheses from thioethers are inevitably impeded by overoxidation, excess oxidants, and the tedious preparation of thioethers. To address these shortcomings, we report herein a highly selective electrochemical sulfoxidation reaction featuring the use of simple starting materials, i.e., thiols and alkyl halides, in a single operation.

Regioselective and oxidant-free sulfinylation of indoles and pyrroles with sulfinamides

An unexpected time-controlled highly selective C3- or C2-sulfinylation of pyrroles with sulfinamides is reported for the first time. The sulfinylation of indoles with sulfinamides using this protocol is oxidant-free and can be performed under obviously more feasible conditions (1.2 equiv. of indoles, 10 min) in comparison with the precedent procedure (3-20 equiv. of indoles, 16-18 h, ammonium persulfate as oxidant, hv). A variety of functional groups were tolerated, and various C2-thioindoles and C2/3-thiopyrroles were obtained in moderate to excellent yields.

Visible-Light Photocatalysis: Does It Make a Difference in Organic Synthesis?

Visible-light photocatalysis has evolved over the last decade into a widely used method in organic synthesis. Photocatalytic variants have been reported for many important transformations, such as cross-coupling reactions, α-amino functionalizations, cycloadditions, ATRA reactions, or fluorinations. To help chemists select photocatalytic methods for their synthesis, we compare in this Review classical and photocatalytic procedures for selected classes of reactions and highlight their advantages and limitations. In many cases, the photocatalytic reactions proceed under milder reaction conditions, typically at room temperature, and stoichiometric reagents are replaced by simple oxidants or reductants, such as air, oxygen, or amines. Does visible-light photocatalysis make a difference in organic synthesis? The prospect of shuttling electrons back and forth to substrates and intermediates or to selectively transfer energy through a visible-light-absorbing photocatalyst holds the promise to improve current procedures in radical chemistry and to open up new avenues by accessing reactive species hitherto unknown, especially by merging photocatalysis with organo- or metal catalysis.

Molecularly imprinted polymers for the analysis and removal of polychlorinated aromatic compounds in the environment: a review

Molecularly imprinted polymers selective to polychlorinated aromatic compounds for application in environmental studies.

Synthesis of novel polymer type sulfoxide solid phase combined with the porogen imprinting for enabling selective separation of polychlorinated biphenyls

We developed a novel polymer type sulfoxide-modified solid phase enabling to achieve selective separation of polychlorinated biphenyls (PCBs) from insulation oil. In this study, firstly we prepared base-polymer based on the concept of the molecular imprinting to capture PCBs in selectively, then, the sulfoxide groups were modified on the pore surface of base-polymers by changing preparation methods. As results of liquid chromatographic analyses for the polymers as columns, the base-polymer prepared by xylene as a porogenic solvent showed selective retention ability for chlorinated aromatic compounds by the porogen imprinting effect. Additionally, the polymer-type sulfoxide solid phases showed highly retention ability for PCBs by increasing amount of introduced sulfoxide groups. Consequently, the results of separation of PCBs comparing to insulation oil suggested that the prepared solid phase can be used for the selective separation of PCBs at the same level as a commercially available media utilized for the regulated method.

Identification of irradiated prawn (Penaeus monodon ) using thermoluminescence and 2-alkylcyclobutanone analyses

Thermoluminescence (TL) and 2-alkylcyclobutanone (2-ACB) analyses were performed to identify irradiated prawns ( Penaeus monodon ). With the TL method, minerals were extracted from prawns using acid hydrolysis. The experimental results satisfied the evaluation criteria of European Norm (EN) 1788, even after low-dose irradiation (0.5 kGy) and a 60 day storage at -20 °C. With the 2-ACB method, 2-dodecylcyclobutanone (2-DCB) and 2-tetradecylcyclobutanone (2-TCB) were successfully extracted from prawns by direct solvent extraction with purification using a conventional silica column and a sulfoxide column, which was used for 2-ACB for the first time. Both 2-ACB derivatives were absent from the non-irradiated samples but were identified in all irradiated samples by gas chromatography-mass spectrometry. Moreover, 2-DCB and 2-TCB production correlated with the applied dose (2.5-10 kGy), and the correlation did not diminish after 60 days of storage at -20 °C for any dose. Therefore, these two techniques provide rapid, simple, and promising methods for routine investigation of frozen prawns.

Mineral oil certified reference materials for the determination of polychlorinated biphenyls from the National Metrology Institute of Japan (NMIJ)

Four mineral oil certified reference materials (CRMs), NMIJ CRM 7902-a, CRM 7903-a, CRM 7904-a, and CRM 7905-a, have been issued by the National Metrology Institute of Japan, which is part of the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST), for the determination of polychlorinated biphenyls (PCBs). The raw materials for the CRMs were an insulation oil (CRM 7902-a and CRM 7903-a) and a fuel oil (CRM7904-a and CRM 7905-a). A solution of PCB3, PCB8, and technical PCB products, comprising four types of Kaneclor, was added to the oil matrices. The total PCB concentrations in the PCB-fortified oils (CRM 7902-a and CRM 7904-a) are approximately 6 mg kg(-1). In addition, the mineral oils which were not fortified with PCBs were also distributed as CRMs (CRM 7903-a and CRM 7905-a). Characterization of these CRMs was conducted by the NMIJ/AIST, where the mineral oils and the PCB solution were analyzed using multiple analytical methods such as dimethylsulfoxide extraction, normal-phase liquid chromatography, gel permeation chromatography, reversed-phase liquid chromatography, and chromatography using sulfoxide-bonded silica; and/or various capillary columns for gas chromatography, and two ionization modes for mass spectrometry. The target compounds in the mineral oils and those in the PCB solution were determined by one of the primary methods of measurement, isotope dilution-mass spectrometry (ID-MS). Certified values have been provided for 11 PCB congeners (PCB3, 8, 28, 52, 101, 118, 138, 153, 180, 194, and 206) in the CRMs. These CRMs have information values for PCB homologue concentrations determined by using a Japanese official method for determination of PCBs in wastes and densities determined with an oscillational density meter. Because oil samples having arbitrary PCB concentrations between respective property values of the PCB-fortified and nonfortified CRMs can be prepared by gravimetric mixing of the CRM pairs, these CRMs can be used for validation of PCB analyses using various instruments which have different sensitivities.