Measuring Photochemical Kinetics in Submonolayer Films by Transient ATR Spectroscopy on a Multimode Planar Waveguide

Direct Nanoscopic Measurement of Laminar Slip Flow Penetration of Deformable Polymer Brush Surfaces: Synergistic Effect of Grafting Density and Solvent Quality

A detailed quantitative nanoscopic description of soft surfaces under dynamic flow is lacking, despite its importance. To better understand the role of surface texture in nanoscopic mass transport in complex media, we used Förster resonance energy transfer in combination with total internal reflectance fluorescence microscopy (FRET-TIRFM) to directly measure laminar slip flow penetration depth (slip length) on poly(N-isopropylacrylamide) (pNIPAM) thin films (50-110 nm) of different grafting densities (0.60, 0.38, and 0.27 chain/nm²) in solvents of different qualities created via cononsolvency in situ. Nontrivial synergistic interplay of grafting density and solvent quality on slip length was observed. Slip lengths are typically tens of nm (40-100 nm), increasing and then reaching a plateau with applied linear flow velocity (192-2,952 μm/s) regardless of experimental system. Slip length was systematically larger for lower density films, but the effect of grafting density was more significant in a good solvent than a poor solvent. Interestingly, however, the stagnant film thickness (polymer swollen thickness minus the slip length) collapsed to almost a singular value for a given grafting density regardless of solvent quality, likely suggesting a large gradient of segmental mobility at nonequilibrium. Moreover, we found that slip flow penetrates into soft pNIPAM surfaces more deeply in a good solvent than in a poor solvent and that this behavior was general and independent of grafting density. This behavior is counter to the notion that less interaction between a fluid (probe) and a solid surface promotes slip.

Reconstitution of bacteriorhodopsin with cationic poly(dimethylaminoethyl acrylate)-block-poly(methylacrylate) for bio-hybrid materials

A kind of cationic amphiphilic copolymer was synthesized for supporting membrane proteins to prepare bio-hybrid materials.

Spectroelectrochemical characterization of small hemoproteins adsorbed within nanostructured mesoporous ITO electrodes

3D nanostructured transparent indium tin oxide (ITO) electrodes prepared by glancing angle deposition (GLAD) were used for the spectroelectrochemical characterization of cytochrome c (Cyt c) and neuroglobin (Nb). These small hemoproteins, involved as electron-transfer partners in the prevention of apoptosis, are oppositely charged at physiological pH and can each be adsorbed within the ITO network under different pH conditions. The resulting modified electrodes were investigated by UV-visible absorption spectroscopy coupled with cyclic voltammetry. By using nondenaturating adsorption conditions, we demonstrate that both proteins are capable of direct electron transfer to the conductive ITO surface, sharing apparent standard potentials similar to those reported in solution. Preservation of the 3D protein structure upon adsorption was confirmed by resonance Raman (rR) spectroscopy. Analysis of the derivative cyclic voltabsorptograms (DCVA) monitored either in the Soret or the Q bands at scan rates up to 1 V s(-1) allowed us to investigate direct interfacial electron transfer kinetics. From the DCVA shape and scan rate dependences, we conclude that the interaction of Cyt c with the ITO surface is more specific than Nb, suggesting an oriented adsorption of Cyt c and a random adsorption of Nb on the ITO surface. At the same time, Cyt c appears more sensitive to the experimental adsorption conditions, and complete denaturation of Cyt c may occur as evidenced from cross-correlation of rR spectroscopy and spectroelectrochemistry.

Electrogenerated chemiluminescence biosensor incorporating ruthenium complex-labelled Concanavalin A as a probe for the detection of Escherichia coli

A novel electrogenerated chemiluminescence (ECL) biosensor for highly sensitive detection of Escherichia coli (E. coli) was first developed by employing Concanavalin A (Con A) as a biological recognition element and bis(2,2'-bipyridine)-4'-methyl-4-carboxybipyridine ruthenium (II) (Ru1) complex as the detector. The ECL biosensor was fabricated by adsorbing carboxyl-functionalised single-wall carbon nanotubes (SWNTs) onto a paraffin-impregnated graphite electrode and further covalently coupling the Ru1-Con A probe onto the surface of the SWNT-modified electrode. Upon the binding of E. coli O157:H7 (as a model target), the biosensor showed a decreased ECL intensity in the presence of tri-n-propylamine (TPrA), which was in logarithmically direct proportion to the concentration of E. coli over a range from 5.0 × 10(2) to 5.0 × 10(5)cells/mL. The detection limit of this sensor was 127 cells/mL. Additionally, the ECL biosensor also showed satisfactory selectivity in discriminating gram-negative E. coli from gram-positive bacteria. The strategy developed in this study may be a promising approach and could be extended to the design of ECL biosensors for highly sensitive and rapid detection of other desired bacteria.