Accounting for Nanometer-Thick Adventitious Carbon Contamination in X-ray Absorption Spectra of Carbon-Based Materials

Why is Superlubricity of Diamond-Like Carbon Rare at Nanoscale?

Hydrogenated diamond-like carbon (HDLC) is a promising solid lubricant for its superlubricity which can benefit various industrial applications. While HDLC exhibits notable friction reduction in macroscale tests in inert or reducing environmental conditions, ultralow friction is rarely observed at the nanoscale. This study investigates this rather peculiar dependence of HDLC superlubricity on the contact scale. To attain superlubricity, HDLC requires i) removal of ≈2 nm-thick air-oxidized surface layer and ii) shear-induced transformation of amorphous carbon to highly graphitic and hydrogenated structure. The nanoscale wear depth exceeds the typical thickness of the air-oxidized layer, ruling out the possibility of incomplete removal of the air-oxidized layer. Raman analysis of transfer films indicates that shear-induced graphitization readily occurs at shear stresses lower than or comparable to those in the nanoscale test. Thus, the same is expected to occur at the nanoscale test. However, the graphitic transfer films are not detected in ex-situ analyses after nanoscale friction tests, indicating that the graphitic transfer films are pushed out of the nanoscale contact area due to the instability of transfer films within a small contact area. Combining all these observations, this study concludes the retention of highly graphitic transfer films is crucial to achieving HDLC superlubricity.

Effect of Europium and Gadolinium Alloying Elements on the Tribological Response of Low Hydrogen Content Amorphous Carbon

Dopants and alloying elements are commonly introduced in amorphous carbon (a-C) materials to tailor their mechanical and tribological properties. While most published studies have focused on doping and alloying a-C coatings with metals or metalloids, doping a-C films with rare-earth elements has only recently been explored. Notably, our understanding of the shear-induced structural changes occurring in rare-earth-element-containing a-C films is still elusive, even in the absence of any liquid lubricants. Here, the friction response of Eu- and Gd-containing a-C films with low hydrogen content deposited by HiPIMS on silicon was evaluated in open air and at room temperature. The load-dependent friction measurements indicated that the introduction of Gd ((2.3 ± 0.1) at.%) and Eu ((2.4 ± 0.1) at.%) into the a-C matrix results in a significant reduction of the shear strength of the sliding interfaces ((41 ± 2) MPa for a-C, (16 ± 1) MPa for a-C:Gd2.3 at.%, and (11 ± 2) MPa for a-C:Eu2.4 at.%). NEXAFS spectromicroscopy experiments provided evidence that no stress-assisted sp3-to-sp2 rehybridization of carbon atoms was induced by the sliding process in the near-surface region of undoped a-C, while the amount of sp2-bonded carbon progressively increased in a-C:Gd2.3 at.% and a-C:Eu2.4 at.% upon increasing the applied normal load in tribological tests. The formation of an sp2-bonded carbon-rich surface layer in a-C:Gd2.3 at.% and a-C:Eu2.4 at.% films was not only proposed to be the origin for the reduced duration of the running-in period in tribological test, but was also postulated to induce shear localization within the sp2-carbon-rich layer and transfer film formation on the countersurface, thus decreasing the interfacial shear strength. These findings open the path for the use of Gd- and Eu-containing a-C even under critical conditions for nearly hydrogen-free a-C films (i.e., humid air).

Superflux of an organic adlayer towards its local reactive immobilization

On-surface mass transport is the key process determining the kinetics and dynamics of on-surface reactions, including the formation of nanostructures, catalysis, or surface cleaning. Volatile organic compounds (VOC) localized on a majority of surfaces dramatically change their properties and act as reactants in many surface reactions. However, the fundamental question "How far and how fast can the molecules travel on the surface to react?" remains open. Here we show that isoprene, the natural VOC, can travel ~1 μm s-1, i.e., centimeters per day, quickly filling low-concentration areas if they become locally depleted. We show that VOC have high surface adhesion on ceramic surfaces and simultaneously high mobility providing a steady flow of resource material for focused electron beam synthesis, which is applicable also on rough or porous surfaces. Our work established the mass transport of reactants on solid surfaces and explored a route for nanofabrication using the natural VOC layer.

Simultaneous quantification of Young's modulus and dispersion forces with nanoscale spatial resolution

Many advances in polymers and layered materials rely on a precise understanding of the local interactions between adjacent molecular or atomic layers. Quantifying dispersion forces at the nanoscale is particularly challenging with existing methods often time consuming, destructive, relying on surface averaging or requiring bespoke equipment. Here, we present a non-invasive method able to quantify the local mechanical and dispersion properties of a given sample with nanometer lateral precision. The method, based on atomic force microscopy (AFM), uses the frequency shift of a vibrating AFM cantilever in combination with established contact mechanics models to simultaneously derive the Hamaker constant and the effective Young's modulus at a given sample location. The derived Hamaker constant and Young's modulus represent an average over a small (typically <100) number of molecules or atoms. The oscillation amplitude of the vibrating AFM probe is used to select the length-scale of the features to analyse, with small vibrations able to resolve the contribution of sub-nanometric defects and large ones exploring effectively homogeneous areas. The accuracy of the method is validated on a range of 2D materials in air and water as well as on polymer thin films. We also provide the first experimental measurements of the Hamaker constant of HBN, MoT2, WSe2and polymer films, verifying theoretical predictions and computer simulations. The simplicity and robustness of the method, implemented with a commercial AFM, may support a broad range of technological applications in the growing field of polymers and nanostructured materials where a fine control of the van der Waals interactions is crucial to tune their properties.

Tribochemistry of Diamond-like Carbon: Interplay between Hydrogen Content in the Film and Oxidative Gas in the Environment

The lubricity of hydrogenated diamond-like carbon (HDLC) films is highly sensitive to the hydrogen (H) content in the film and the oxidizing gas in the environment. The tribochemical knowledge of HDLC films with two different H-contents (mildly hydrogenated vs highly hydrogenated) was deduced from the analysis of the transfer layers formed on the counter-surface during friction tests in O2 and H2O using Raman spectroscopic imaging and X-ray photoelectron spectroscopy (XPS). The results showed that, regardless of H-content in the film, shear-induced graphitization and oxidation take place readily. By analyzing the O2 and H2O partial pressure dependence of friction of HDLC with a Langmuir-type reaction kinetics model, the oxidation probability of the HDLC surface exposed by friction as well as the removal probability of the oxidized species by friction were determined. The HDLC film with more H-content exhibited a lower oxidation probability than the film with less H-content. The atomistic origin of this H-content dependence was investigated using reactive molecular dynamics simulations, which showed that the fraction of undercoordinated carbon species decreased as the H-content in the film increased, corroborating the lower oxidation probability of the highly-hydrogenated film. The H-content in the HDLC film influenced the probabilities of oxidation and material removal, both of which vary with the environmental condition.

Atomic Cross-Talk at the Interface: Enhanced Lubricity and Wear and Corrosion Resistance in Sub 2 nm Hybrid Overcoats via Strengthened Interface Chemistry

Friction, wear, and corrosion remain the major causes of premature failure of diverse systems including hard-disk drives (HDDs). To enhance the areal density of HDDs beyond 1 Tb/in², the necessary low friction and high wear and corrosion resistance characteristics with sub 2 nm overcoats remain unachievable. Here we demonstrate that atom cross-talk not only manipulates the interface chemistry but also strengthens the tribological and corrosion properties of sub 2 nm overcoats. High-affinity (HA) atomically thin (∼0.4 nm) interlayers (ATIs, X_HA), namely Ti, Si, and SiN_x, are sandwiched between the hard-disk media and 1.5 nm thick carbon (C) overlayer to develop interface-enhanced sub 2 nm hybrid overcoats that consistently outperform a thicker conventional commercial overcoat (≥2.7 nm), with the C/SiN_x bilayer overcoat bettering all other <2 nm thick overcoats. These hybrid overcoats can enable the development of futuristic 2-4 Tb/in² areal density HDDs and can transform various moving-mechanical-system based technologies.

Visible-Light-Driven Photocatalytic Inactivation of Bacteria, Bacteriophages, and Their Mixtures Using ZnO-Coated HDPE Beads as Floating Photocatalyst

Semiconductor materials used as photocatalysts are considered among the most effective ways to treat biologically polluted water. Certainly, efficiency depends on the selection of photocatalyst and its substrate, as well as the possibility of its application in a broader spectrum of light. In this study, a reactive magnetron sputtering technique was applied for the immobilisation of ZnO photocatalyst on the surface of HDPE beads, which were selected as the buoyant substrates for enhanced photocatalytic performance and easier recovery from the treated water. Moreover, the study compared the effect on the inactivation of the microorganism between ZnO-coated HDPE beads without Ni and with Ni underlayer. Crystal structure, surface morphology, and chemical bonds of as-deposited ZnO films were investigated by X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy, respectively. Visible-light-induced photocatalytic treatment was performed on the Gram-negative and Gram-positive bacteria and bacteriophages PRD1, T4, and their mixture. Higher bacteria inactivation efficiency was obtained using the ZnO photocatalyst with Ni underlayer for the treatment of S. Typhimurium and M. Luteus mixtures. As for infectivity of bacteriophages, T4 alone and in the mixture with PRD1 were more affected by the produced photocatalyst, compared with PRD1.

Rubrene Thin Films with Viably Enhanced Charge Transport Fabricated by Cryo-Matrix-Assisted Laser Evaporation

Among organic semiconductors, rubrene (RB; C₄₂H₂₈) is of rapidly growing interest for the development of organic and hybrid electronics due to exceptionally long spin diffusion length and carrier mobility up to 20 cm²V⁻¹s⁻¹ in single crystals. However, the fabrication of RB thin films resembling properties of the bulk remains challenging, mainly because of the RB molecule’s twisted conformation. This hinders the formation of orthorhombic crystals with strong π–π interactions that support the band transport. In this work, RB films with a high crystalline content were fabricated by matrix-assisted laser evaporation and the associated structure, composition, and transport properties are investigated. Enhanced charge transport is ascribed to the crystalline content of the film. Spherulitic structures are observed on top of an amorphous RB layer formed in the initial deposition stage. In spherulites, orthorhombic crystals dominate, as confirmed by X-ray diffraction and the absorption and Raman spectra. Surprisingly, nanowires several microns in length are also detected. The desorption/ionization mass and X-ray photoelectron spectra consistently show minimal material decomposition and absence of RB peroxides. The observed carrier mobility up to 0.13 cm²V⁻¹s⁻¹, is close to the technologically accepted level, making these rubrene films attractive for spintronic and optoelectronic applications.

Formation of an Artificial Mg2+-Permeable Interphase on Mg Anodes Compatible with Ether and Carbonate Electrolytes

Rechargeable Mg-ion batteries typically suffer from either rapid passivation of the Mg anode or severe corrosion of the current collectors by halogens within the electrolyte, limiting their practical implementation. Here, we demonstrate the broadly applicable strategy of forming an artificial solid electrolyte interphase (a-SEI) layer on Mg to address these challenges. The a-SEI layer is formed by simply soaking Mg foil in a tetraethylene glycol dimethyl ether solution containing LiTFSI and AlCl₃, with Fourier transform infrared and ultraviolet-visible spectroscopy measurements revealing spontaneous reaction with the Mg foil. The a-SEI is found to mitigate Mg passivation in Mg(TFSI)₂/DME electrolytes with symmetric cells exhibiting overpotentials that are 2 V lower compared to when the a-SEI is not present. This approach is extended to Mg(ClO₄)₂/DME and Mg(TFSI)₂/PC electrolytes to achieve reversible Mg plating and stripping, which is not achieved with bare electrodes. The interfacial resistance of the cells with a-SEI protected Mg is found to be two orders of magnitude lower than that with bare Mg in all three of the electrolytes, indicating the formation of an effective Mg-ion transporting interfacial structure. X-ray absorption and photoemission spectroscopy measurements show that the a-SEI contains minimal MgCO₃, MgO, Mg(OH)₂, and TFSI^-, while being rich in MgCl₂, MgF₂, and MgS, when compared to the passivation layer formed on bare Mg in Mg(TFSI)₂/DME.

How Hydrogen and Oxygen Vapor Affect the Tribochemistry of Silicon- and Oxygen-Containing Hydrogenated Amorphous Carbon under Low-Friction Conditions: A Study Combining X-ray Absorption Spectromicroscopy and Data Science Methods

The incorporation of silicon and oxygen into hydrogenated amorphous carbon (a-C:H) is an effective approach to decrease the dependence of the tribological properties of a-C:H on the environment. Here, we evaluate the effect of hydrogen and oxygen partial pressures in vacuum on the tribological response of steel pins sliding against films consisting of silicon- and oxygen-containing a-C:H (a-C:H:Si:O). Experiments are conducted in the low-friction/low-wear regime, where sufficient gas pressure prevents steel from adhering to the a-C:H:Si:O, with the velocity accommodation mode being interfacial sliding between the tribotrack formed in the a-C:H:Si:O film and the carbonaceous tribofilm that is formed on the countersurface. The experiments indicated a decrease (increase) in friction and wear with the hydrogen (oxygen) pressure (hydrogen pressures between 50 and 2000 mbar; oxygen pressures between 10 and 1000 mbar). Characterization by X-ray photoelectron and absorption spectroscopies indicated the occurrence of tribologically induced rehybridization of carbon-carbon bonds from sp³ to sp². This mechanically induced structural transformation coincided with the dissociative surface reaction between hydrogen (oxygen) gas molecules and sp² carbon-carbon bonds that are highly strained, which results in the formation of carbon-hydrogen groups (carbonyl or ether groups together with silicon atoms having higher oxidation states). On the basis of variations of the fraction of these surface functional groups with gas pressure, a phenomenological model is proposed for the gas pressure dependence of friction for steel when sliding on a-C:H:Si:O films: while the decrease in friction with hydrogen pressure is induced by an increase in the percentage of carbon-hydrogen groups, the increase in friction with oxygen pressure is caused by a progressive increase in the relative fraction of silicon atoms having higher oxidation states and an increase in surface oxygen concentration.

New details of assembling bioactive films from dispersions of amphiphilic molecules on titania surfaces

Tailoring the surface properties of materials for biomedical applications is important to avoid clinical complications. Forming thin layers of amphiphilic molecules with apolar regions that facilitate attractive intermolecular interactions, can be a suitable and versatile approach to achieve hydrophobic surface modification and provide functional antibacterial properties. Aiming to correlate layer structure and properties starting from film formation, octadecylphosphonic acid (ODPA) and dimethyloctadecyl (3-trimethoxysilylpropyl) ammonium chloride (DMOAP) layers were adsorbed onto smooth titania surfaces. Then the films were studied by atomic force microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS), and their interactions with aqueous environments were characterized by contact angle and zeta potential measurements. In addition, antibacterial assays were performed using E. coli and S. mutants to reveal the antibacterial properties effected by the surface modification. Immediately after sputter deposition, titania was hydrophilic; however, after air storage and adsorption of DMOAP or ODPA, an increase in the water contact angle was observed. XPS investigations after layer formation and after antibacterial tests revealed that the attachment of layers assembled from ODPA on titania substrates is considerably stronger and more stable than that observed for DMOAP films. Heat treatment strongly affects DMOAP layers. Furthermore, DMOAP layers are not stable under biological conditions.

Structure–property relationship of amphiphilic molecules on smooth substrates was explored through a multi-step approach and its influence on biological activity.

Carbon doping switching on the hydrogen adsorption activity of NiO for hydrogen evolution reaction

Hydrogen evolution reaction (HER) is more sluggish in alkaline than in acidic media because of the additional energy required for water dissociation. Numerous catalysts, including NiO, that offer active sites for water dissociation have been extensively investigated. Yet, the overall HER performance of NiO is still limited by lacking favorable H adsorption sites. Here we show a strategy to activate NiO through carbon doping, which creates under-coordinated Ni sites favorable for H adsorption. DFT calculations reveal that carbon dopant decreases the energy barrier of Heyrovsky step from 1.17 eV to 0.81 eV, suggesting the carbon also serves as a hot-spot for the dissociation of water molecules in water-alkali HER. As a result, the carbon doped NiO catalyst achieves an ultralow overpotential of 27 mV at 10 mA cm^-2, and a low Tafel slope of 36 mV dec^-1, representing the best performance among the state-of-the-art NiO catalysts.

Diamond growth from organic compounds in hydrous fluids deep within the Earth

At subduction zones, most diamonds form by carbon saturation in hydrous fluids released from lithospheric plates on equilibration with mantle rocks. Although organic molecules are predicted among dissolved species which are the source for carbon in diamonds, their occurrence is not demonstrated in nature, and the physical model for crustal diamond formation is debated. Here, using Raman microspectroscopy, I determine the structure of carbon-based phases inside fluid inclusions in diamond-bearing rocks from the Alps. The results provide direct evidence that diamond surfaces are coated by sp²-, and sp³-bonded amorphous carbon and functional groups of carboxylic acids (e.g., carboxyl, carboxylate, methyl, and methylene), indicating the geosynthesis of organic compounds in deep hydrous fluids. Moreover, this study suggests diamond nucleation via metastable molecular precursors. As a possible scenario, with carbon saturation by reduction of carboxylate groups, I consider tetrahedral H-terminated C groups as templates for the growth of sp³-structured carbon.

Diamonds can give us clues to the processes regulating deep carbon transport within the Earth. Here, the author discovers evidence from diamond coatings that organic compounds exist at great depth in Earth’s interior, and furthermore, that organic molecules may provide scaffolds for diamond nucleation and growth.

Adlayer-Free Large-Area Single Crystal Graphene Grown on a Cu(111) Foil

To date, thousands of publications have reported chemical vapor deposition growth of "single layer" graphene, but none of them has described truly single layer graphene over large area because a fraction of the area has adlayers. It is found that the amount of subsurface carbon (leading to additional nuclei) in Cu foils directly correlates with the extent of adlayer growth. Annealing in hydrogen gas atmosphere depletes the subsurface carbon in the Cu foil. Adlayer-free single crystal and polycrystalline single layer graphene films are grown on Cu(111) and polycrystalline Cu foils containing no subsurface carbon, respectively. This single crystal graphene contains parallel, centimeter-long ≈100 nm wide "folds," separated by 20 to 50 µm, while folds (and wrinkles) are distributed quasi-randomly in the polycrystalline graphene film. High-performance field-effect transistors are readily fabricated in the large regions between adjacent parallel folds in the adlayer-free single crystal graphene film.

Thermally Induced Structural Evolution of Silicon- and Oxygen-Containing Hydrogenated Amorphous Carbon: A Combined Spectroscopic and Molecular Dynamics Simulation Investigation

Silicon- and oxygen-containing hydrogenated amorphous carbon (a-C:H:Si:O) coatings are amorphous thin-film materials composed of hydrogenated amorphous carbon (a-C:H), doped with silicon and oxygen. Compared to a-C:H, a-C:H:Si:O exhibits much lower susceptibility to oxidative degradation and higher thermal stability, making a-C:H:Si:O attractive for many applications. However, the physical mechanisms for this improved behavior are not understood. Here, the thermally induced structural evolution of a-C:H:Si:O was investigated in situ by X-ray photoelectron and absorption spectroscopy, as well as molecular dynamics (MD) simulations. The spectroscopy results indicate that upon high vacuum annealing, two thermally activated processes with a Gaussian distribution of activation energies with mean value E and standard deviation σ take place in a-C:H:Si:O: (a) ordering and clustering of sp² carbon ( E ± σ = 0.22 ± 0.08 eV) and (b) conversion of sp³- to sp²-bonded carbon ( E ± σ = 3.0 ± 1.1 eV). The experimental results are in qualitative agreement with the outcomes of MD simulations performed using a ReaxFF potential. The MD simulations also indicate that the higher thermal stability of a-C:H:Si:O compared to a-C:H (with similar fraction of sp²-bonded carbon and hydrogen content) derives from the significantly lower fraction of strained carbon-carbon sp³ bonds in a-C:H:Si:O compared to a-C:H, which are more likely to break at elevated temperatures.

Superior wear resistance and low friction in hybrid ultrathin silicon nitride/carbon films: synergy of the interfacial chemistry and carbon microstructure

Amorphous carbon-based films are commonly investigated as protective nanocoatings in macro- to nano-scale devices due to their exceptional tribological and mechanical properties. However, with further device miniaturization where even thinner coatings are required, the wear durability of the nanocoating rapidly degrades at the expense of lower thickness. Here we discover that for sub-10 nm coating thicknesses, a hybrid bi-layer film structure, comprising a high sp³-bonded amorphous carbon top layer and a silicon nitride (SiN_x) bottom layer, consistently outperforms its single-layer amorphous carbon counterpart in terms of wear durability on a commercial tape drive head, while exhibiting low, stable friction and excellent wear resistance on a flat ceramic substrate. The superior performance of the hybrid film is attributed to the constructive synergy of the sp³-rich carbon microstructure and an enhanced interfacial chemistry arising from additional interfacial bonding. Moreover, a high energy C⁺ ion treatment step, introduced either directly to the substrate or to the SiN_x layer before carbon deposition, also aids in increasing atomic mixing that contributes to further improvement in the wear resistance. This study highlights the importance of both the carbon microstructure and interfacial chemistry in the design of wear-durable nanocoatings at few-nanometer thicknesses, particularly for aggressive wear conditions.

Characterization of the Intrinsic Water Wettability of Graphite Using Contact Angle Measurements: Effect of Defects on Static and Dynamic Contact Angles

Elucidating the intrinsic water wettability of the graphitic surface has increasingly attracted research interests, triggered by the recent finding that the well-established hydrophobicity of graphitic surfaces actually results from airborne hydrocarbon contamination. Currently, static water contact angle (WCA) is often used to characterize the intrinsic water wettability of graphitic surfaces. In the current paper, we show that because of the existence of defects, static WCA does not necessarily characterize the intrinsic water wettability. Freshly exfoliated graphite of varying qualities, characterized using atomic force microscopy and Raman spectroscopy, was studied using static, advancing, and receding WCA measurements. The results showed that graphite of different qualities (i.e., defect density) always has a similar advancing WCA, but it could have very different static and receding WCAs. This finding indicates that defects play an important role in contact angle measurements, and the static contact angle does not always represent the intrinsic water wettability of pristine graphite. On the basis of the experimental results, a qualitative model is proposed to explain the effect of defects on static, advancing, and receding contact angles. The model suggests that the advancing WCA reflects the intrinsic water wettability of pristine (defect-free) graphite. Our results showed that the advancing WCA for pristine graphite is 68.6°, which indicates that graphitic carbon is intrinsically mildly hydrophilic.

Fluorinated Graphene Enables the Growth of Inorganic Thin Films by Chemical Bath Deposition on Otherwise Inert Substrates

Chemically modified graphenes (CMGs) offer a means to tune a wide variety of graphene's exceptional properties. Critically, CMGs can be transferred onto a variety of substrates, thereby imparting functionalities to those substrates that would not be obtainable through conventional functionalization. One such application of CMGs is enabling and controlling the subsequent growth of inorganic thin films. In the current study, we demonstrated that CMGs enhance the growth of inorganic films on inert surfaces with poor growth properties. Fluorinated graphene transferred onto polyethylene enabled the dense and homogeneous deposition of a cadmium sulfide (CdS) film grown via chemical bath deposition. We showed that the coverage of the CdS film can be controlled by the degree of fluorination from less than 20% to complete coverage of the film. The approach can also be applied to other technologically important materials such as ZnO. Finally, we demonstrated that electron beam-generated plasma in a SF₆-containing background could pattern fluorine onto a graphene/PE sample to selectively grow CdS films on the fluorinated region. Therefore, CMG coatings can tailor the surface properties of polymers and control the growth of inorganic thin films on polymers for the development of flexible electronics.

Influence of O2, H2O and airborne hydrocarbons on the properties of selected 2D materials

Adsorption of molecules from the ambient environment significantly changes the optical, electrical, electrochemical, and tribological properties of 2D materials.

Atomic Scale Interface Manipulation, Structural Engineering, and Their Impact on Ultrathin Carbon Films in Controlling Wear, Friction, and Corrosion

Reducing friction, wear, and corrosion of diverse materials/devices using <2 nm thick protective carbon films remains challenging, which limits the developments of many technologies, such as magnetic data storage systems. Here, we present a novel approach based on atomic scale interface manipulation to engineer and control the friction, wear, corrosion, and structural characteristics of 0.7-1.7 nm carbon-based films on CoCrPt:oxide-based magnetic media. We demonstrate that when an atomically thin (∼0.5 nm) chromium nitride (CrNx) layer is sandwiched between the magnetic media and an ultrathin carbon overlayer (1.2 nm), it modifies the film-substrate interface, creates various types of interfacial bonding, increases the interfacial adhesion, and tunes the structure of carbon in terms of its sp(3) bonding. These contribute to its remarkable functional properties, such as stable and lowest coefficient of friction (∼0.15-0.2), highest wear resistance and better corrosion resistance despite being only ∼1.7 nm thick, surpassing those of ∼2.7 nm thick current commercial carbon overcoat (COC) and other overcoats in this work. While this approach has direct implications for advancing current magnetic storage technology with its ultralow thickness, it can also be applied to advance the protective and barrier capabilities of other ultrathin materials for associated technologies.

Superlubrication properties of ultra-nanocrystalline diamond film sliding against a zirconia ball

The friction and wear behavior of ultra-nanocrystalline diamond (UNCD) films are sensitive to the phase composition, mainly graphite and amorphous carbon (a-C), occupying the grain boundaries of sp³ hybridized diamond nanocrystals.